For anyone that runs into the problem of that green clip attached to the one cable behind the resonator box when you go to remove it that isn’t shown in this video or many others. To get it off I used a flat head screw driver to get underneath the little clip and lifted it off, with some effort it came off just be careful not to puncture the cable it’s connected too or unplug it! I searched high and low for an answer on this a scrolled through 30 forms to find an answer for it, so I figured I’d share it here! good luck everyone :)
Awesome vid, just bought an identical one and I'm glad I found this video. I didnt even buy it for extra power, even if it could manage that, I mostly bought it to clean up the engine bay and make it sound a bit better. And by the looks of this video, it does great in all categories. Thanks for giving a detailed vid 💯
May I ask what the purpose of this intake is? I'm actually thinking of doing this because the bolts are stripped on my case set and can't change my filter.
Dude, it's damned cold and I knew that the moment I saw the snow on the windshield in the beginning. Great job trying to be as detailed as possible while being cold!
i have the exact same intake for my 02 civic ex coupe and the thing with this cold air intake is that it's actually suppose to sit under the battery and thats the reason many people don't think it fits properly.
Man I just bought a fairly mint 03 Civic LX that was unmarked I'm glad I found your channel it looks like the same exact setup, I'm really new to this hobby and was looking for suggestions for bringing it more up to Civic standards? thanks man and keep up the awesome work!
Have one of these civics, did the same thing and the improved sound suggested speed until a pal of mine with the identical car smoked me with the original set up. Only a cold air set up routing the intake hose or pipe through the hole on the right apron of the car increases torque a little.
cause you got a short ram intake. Not a cold air intake. Short ram intake purely cosmetic and is actually worst then stock intake. Cold air intake on the other hand is just slightly better then stock in take and looks nice cosmetically but pay a lot more for the small added amount of metal.
Can someone tell me where and how I can get that mounting bracket for my d17a??? My engine doesn’t have the resonator mounting bracket... should I hit up a junk yard?
I just bought a short ram for my 02 civic, but there is only 1 hole for the rubber tube, there's no second hole for the ma sensor. Do I need to plug this back in or can I run it without the sensor? Anyone have any suggestions?? I'd really appreciate it! 🙏🏻🙏🏻💯
I did a cold air intake on my civic just like yours too and there's is no need to take out the battery that's just more work and you don't have to open up the air box to take out senser you can just t pull it right out.
I saw thew thumbnail and it almost scared me I replaced my air intake with an identical intake as you did and the picture you used for the thumbnail looked exactly like the one I took after I finished
When you shut it off does it have that long flight air draw at the end that sounds like a jet engine cooling down or something. I always loved how the Honda Accords sound with pod filters.
Yo Beastie what up? do you remember the link of the page where you buy the intake?, im a real follower man, i have a 2002 civic sedan, same engine than yours :D
For some reason the intake I am unable to remove from the car it's as if there is a cable/sensor attached any ideas on how/what this is as you was able just to pull it out?
Joey Reina it depends on the intake and the strut bar , I’ve herd DC sports carbon steel on fits with K and N but it’s a gamble if u are ordering it from online
If the intake pipe doesn't clear the strut tower bar, just take off the pipe off and trim it off at the end where it meets the factory throttle body. A saw should do the trick, just remember to sand and smooth out the area of the pipe (as well as clean it) before you install it in order to avoid any metal from entering your throttle body and cause damage to the engine. Good luck to you.
Hello friend I live in México City , I have one Civic EX MT 02 Put Tenzo R Bar but whit K&N replace , with the same air box of Factory , was the best option for me and for you with out problems , The air is cold , in this case the air its hot for the metal tube ... 👍🏻
I have a 1999 crv. I want to move my oil filter up into the engine bay but I need to do a mod like this to make room for the relocation hardware for the oil filter. Where did you buy your short ram intake from? that engine compartment is dam tight, i hope this works. what are your views? great video by the way!
THATS BEAUTIFUL. I ASKED A FEW PEOPLE THAT I WANT TO INSTALL A COKD AIR INTAKE MY FRIENDS ARE LIKE ITS WAY TO MUCH WORK.....AFTWR WATCHING THIS VIDEO IM BUYING OHE ASAP
Im putting back my stock air box cuss in the summer the short ram sucks in too much hot air. then the rubber tube that connects to the engine got bent from the heat. Car ran hottter. A cold air intake would be a better option but you still have to get it on a dyno to config the computer. thats expensive. not worth the 5 extra HP.
For anyone that runs into the problem of that green clip attached to the one cable behind the resonator box when you go to remove it that isn’t shown in this video or many others. To get it off I used a flat head screw driver to get underneath the little clip and lifted it off, with some effort it came off just be careful not to puncture the cable it’s connected too or unplug it! I searched high and low for an answer on this a scrolled through 30 forms to find an answer for it, so I figured I’d share it here! good luck everyone :)
This will be relevant for ages 💯
Just bought an intake because this is out there thanks man 💯💯
Thanks for the great, detailed installation video. Will make my install so much easier tomorrow morning!
Lol weird, 4 years apart but same thing happening tomorrow morning
Nice video.The installation and the before and after sounds from the engine, drivers seat, and exhaust. That was exactly what i was looking for.
Love this video, its complete with videos of things curious people look for and listen to. Keep it up!
Awesome vid, just bought an identical one and I'm glad I found this video. I didnt even buy it for extra power, even if it could manage that, I mostly bought it to clean up the engine bay and make it sound a bit better. And by the looks of this video, it does great in all categories. Thanks for giving a detailed vid 💯
May I ask what the purpose of this intake is? I'm actually thinking of doing this because the bolts are stripped on my case set and can't change my filter.
I bought a small hand saw from Home Depot and sawed in the middle of the screw. I then used a flathead screwdriver to take them out.
More sound and at high revs a liitle less slower.
Just installed my short ram today. I live in colder climates as well so it's perfect.
Dude, it's damned cold and I knew that the moment I saw the snow on the windshield in the beginning. Great job trying to be as detailed as possible while being cold!
i have the exact same intake for my 02 civic ex coupe and the thing with this cold air intake is that it's actually suppose to sit under the battery and thats the reason many people don't think it fits properly.
interesting. thx
He got the same one I got ... and the bracket doesn't line up to mount with anything...
Exactly video I was looking for thanks bro subbed
Saw the rasta colors an welcome to jamrock starting playin in my head
Do you have the link to where you bought this pipe. Can't get one with two holes at that angle anywhere
Ebay 69$
Man I just bought a fairly mint 03 Civic LX that was unmarked I'm glad I found your channel it looks like the same exact setup, I'm really new to this hobby and was looking for suggestions for bringing it more up to Civic standards? thanks man and keep up the awesome work!
POOLBOY Willis catback exhaust , air intake , wheels , and lower it that’s it !
@@bored2323 hey thanks alot man!
THANK YOU SO MUCH FOR THIS KIK ASS INSTALATION VIDEO
It's amazing how none of your screws are rusted! Dam near all of mine are Rusted on, i bought a cai so I'm gonna pry open the top to get the sensor
Have one of these civics, did the same thing and the improved sound suggested speed until a pal of mine with the identical car smoked me with the original set up. Only a cold air set up routing the intake hose or pipe through the hole on the right apron of the car increases torque a little.
cause you got a short ram intake. Not a cold air intake. Short ram intake purely cosmetic and is actually worst then stock intake. Cold air intake on the other hand is just slightly better then stock in take and looks nice cosmetically but pay a lot more for the small added amount of metal.
Did the check engine light ever go on for this?
did not with mine
Can someone tell me where and how I can get that mounting bracket for my d17a??? My engine doesn’t have the resonator mounting bracket... should I hit up a junk yard?
I just bought a short ram for my 02 civic, but there is only 1 hole for the rubber tube, there's no second hole for the ma sensor. Do I need to plug this back in or can I run it without the sensor? Anyone have any suggestions?? I'd really appreciate it! 🙏🏻🙏🏻💯
You need to
Run it with the sensor
EXCELLENT VIDEO THIS ENGINE IS IDENTICAL TO MY 2002 CIVIC SI VELOS
yo where would I get that rubber piece thats on the pipe already for the IAT sensor? I can't find it online :/
I dipped my head irl tryna get a better angle 😂
I did a cold air intake on my civic just like yours too and there's is no need to take out the battery that's just more work and you don't have to open up the air box to take out senser you can just t pull it right out.
It's not cold air it's a short ram, and the improvement is only at the top end from my experience.
Should have done the D16Y8 manifold swap!
You mean B16Y8?
Shijn / Siouxer there’s no such thing as b16y8😂 it’s d16
I saw thew thumbnail and it almost scared me I replaced my air intake with an identical intake as you did and the picture you used for the thumbnail looked exactly like the one I took after I finished
When you shut it off does it have that long flight air draw at the end that sounds like a jet engine cooling down or something. I always loved how the Honda Accords sound with pod filters.
Thanks for the video good sir, I purchased the exact same one but they forgot to include instructions, so super easy to install, thanks again. 👍
Was looking for this specific video because not all intake manifolds are sideways like this one , I was a little confused looking at my hood
Nice video I am going to be installing a Cold Air Intake on my 2005 Civic with my dad and im sure this video is gonna help us :)
Just in case yall were wonder my car is a 5 speed manual
Lets take off a factory COLD air intake and put our own HOT air intake. Yeah !!
Hahahaha
its sucking in hotter air now...
That sounds beautiful, you gotta love hondas man. The underdog!
@@DieselDog1982 you sir are a galit
This is going to be a stupid question. But what does this do for the vehicle?
I hope this civic has had a valve adjustment by now.... can hear all the intake valves clacking, can't say much for the burned up exhaust valves. lol
Did this to my car and it won’t start. Turning over, but no starting! Anyone know what might cause this?
Awesome video. So helpful and explains everything we need to know when installing a cold feed kit.
Yo Beastie what up? do you remember the link of the page where you buy the intake?, im a real follower man, i have a 2002 civic sedan, same engine than yours :D
I just threw that dna header on mine do you recommend the intake swap as well Beastie?
Just got a 2005 ep2 😊 yoop yoop. Subscribed to your channel.. keep the vids coming mate. 🤗
Good shit on the sound before/after. huge for video which is usually forgotten.
I'm thinking of buying it but would it work on an auto transmission civic too?
also want to knownrhis
bro,what size red hose form manifold intake?
What is the diameter of the air intake pipe
Did u get a check engine light?
Why you did not put the 2 pipes. What's the difference? Is it better?
Beast boy, I need this kit. Where did you but it and what's the name of it? Can anyone help with that
It sounds great man!! do you have a driving test with the new short ram on it? You Should if you don't yet.
I was wondering were you able to close your hood? I have the same car and wanted to put the same intake on?
what is the internal diameter of the silicone tubing (the big one)
This video was one of the best and most helpful video hand down thank you very
JUST A THOUGHT.....IS THIS SETUP LEGAL FOR CALIF. SMOG LAWS..??
did you ever figure out the rest of the intake
Your installing a cold air intake but the video says SHORT RAM INTAKE... check it
been searching for this vid...! thx brother
Bought the same exact CAI and I have the same problem. It wouldn't even sit under the battery.
Same here
For some reason the intake I am unable to remove from the car it's as if there is a cable/sensor attached any ideas on how/what this is as you was able just to pull it out?
TheDrillMixtape i had a cable wich was clamped to the second airbox
@@tanium275 any idea what that cable was? I just snapped it off, I'm going to have to re-route it haha
@@asdfjkl74able engine wireing
lol coolant filled up to the cap?? theres a max line way at the bottom of ur car
Where is the EGR valve on this model?
can a strut bar fit with this intake? I tried calling K&N and they didn't have an answer for me
Joey Reina it depends on the intake and the strut bar , I’ve herd DC sports carbon steel on fits with K and N but it’s a gamble if u are ordering it from online
If the intake pipe doesn't clear the strut tower bar, just take off the pipe off and trim it off at the end where it meets the factory throttle body.
A saw should do the trick, just remember to sand and smooth out the area of the pipe (as well as clean it) before you install it in order to avoid any metal from entering your throttle body and cause damage to the engine.
Good luck to you.
Hello friend I live in México City , I have one Civic EX MT 02 Put Tenzo R Bar but whit K&N replace , with the same air box of Factory , was the best option for me and for you with out problems , The air is cold , in this case the air its hot for the metal tube ... 👍🏻
I have a 1999 crv. I want to move my oil filter up into the engine bay but I need to do a mod like this to make room for the relocation hardware for the oil filter. Where did you buy your short ram intake from? that engine compartment is dam tight, i hope this works. what are your views? great video by the way!
Yo when I was taking the bolts out of the air filter housing 2 of them snapped off. Any idea how I can fix this?
Hi just wondering where did u get the pod kit from
lol only good thats doing for your car is it's warming up faster in winter cuz of all that hot air it's sucking in
did your check engine light ever come on after installing the intake?
No. This would only happen if you failed to reconnect the maf sensor
Can you post the link where you got your pipes and filter? Thanks
Thanks just found this vid... Think i'll do my honda, seems easy
where did you buy this kit from I want one for my car
on Ebay, really easy to find
Brady Holmberg I bought an identical one on 1a auto
I NOTICE YOU DONT HAVE AN EGR VALVE ON YOUR HONDA DID IT COME WITH ONE?
egr is a diesel part?
Ummm they didn't make a diesel engine for this year.. EGR valves are installed on the ULEV D17A1 1.7L L4 CARB compliant models.
No they come on the d16v1
Will the car pass smog with it
Where did you purchase the intake pipe with filter?
how often after you install it does it need a replacement filter?
filter can be cleaned w/simple green.
Not even a heat shield?
Great work. Helped me out a lot
Thanks my friend; the video was very helpful...good job.
bro your idle RPM is 1300??
where are you this buy ?
Will this make the stututu sound?
Good job man.🔧🔩
Love this video.. your engine is D15b is your transmission cvt?
Great video bro, subbed and liked
THATS BEAUTIFUL. I ASKED A FEW PEOPLE THAT I WANT TO INSTALL A COKD AIR INTAKE MY FRIENDS ARE LIKE ITS WAY TO MUCH WORK.....AFTWR WATCHING THIS VIDEO IM BUYING OHE ASAP
good video buddy well explained 👏👏👏👍
What muffler do you have on this car ?
Do you put oil to the filter?
Does this mod require a tune?
Yo bro just used this vid!!! Thanks for the help!!!!
What type intake is it
where can I buy an cold air intake for my 2002 Honda civic lx auto transmission ???
Bryan Pineda eBay
is it advisable for stock auto engine? civic 02 1.7 exi. thanks.
lambert Muriel hot air intakes are never recommend
Anyone know where I can buy a replacement filter for this
Marty Annunziata eBay or ur local auto parts store, just bring in the original
is your car standard or auto transmission ??
Where did you buy the intake?
Im putting back my stock air box cuss in the summer the short ram sucks in too much hot air. then the rubber tube that connects to the engine got bent from the heat. Car ran hottter. A cold air intake would be a better option but you still have to get it on a dyno to config the computer. thats expensive. not worth the 5 extra HP.
my iat sensor bugging
I have an 04 civic how much hp I herd it's 15 hp more but i don't know for sure
No way it's 15. Maybe a 5 gain. Mpg' should go up a few.
15 bro I'm a mechanic
lmao so we should trust you, huh? lol
doubt it
How to lnstall cold alr lntake to 2009 civic
I'm a drummer to great to see another one thanks
>revving the engine cold
REEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEEE
No prob. Ask my x
How does he rev it while being on the engine bay?
The throttle body