I also have this drill, but I was not able to remove the chuck. I tried the same method with an Allen key but without any luck. I was afraid I might destroy it completely, so in the end, I just removed all the screws, split the plastic case as much as possible, and removed the control board. Then I desoldered the wires from the motor and repaired the board. I replaced all the MOSFETs (just to be sure). I bought them from TME, and they look different than yours... After the repair, I soldered the board back to the motor wires, covered it with silicon, and put it all together. The drill now works without any problems. A review from "AllHandmade" shows how to take it apart.
Incredible fix, great job! I hate this design where you have to take the chuck out, to take apart the drill. Einhell also does this on some of their drill and it is really a terrible design
Unbelievable!?! Only yesterday I spent an hour+ searching for any information how to take apart this exact model. Great job. Do you think we can find those bldc driver/controller boards from China?
I also searched a lot but couldn't find how to disassemble it. And I thought the chuck had to be removed first. I don't think you'll find the same controller, except for some poor quality controller
This qas probably still under warranty, but good to see you fix it. Also you might want to look into alternative for mosfets becausr alpha&omega semiconductor ones are kinda crap.
@@ErCanEverythingtodo muy bien y otras reparaciones también, a ver para cuando una reparación de sierra circular de esta marca que cortó bien unos 20 metros de tablero de aglomerado de 10mm y ya no sale ningún corte bien, sierra nueva, disco de sierra nuevo, no se a golpeado ni se a caído, probé a apretar y o aflojar tornillos y sigue igual 😢, saludos desde iberia
Finaly a solution for my problem . I would like to know what are those little chips and where can i buy them. And my drill chuck is holding on so tight i cant get it off but i will try
I also left links to the transistors in the description. It is very difficult to remove the chuck, I have one that I did not manage to remove. There is a possibility that you will damage the gearbox. Otherwise, if it worked, it would be easier and always try in first gear.
Allen anahtarla açtığın mandreni öyle çekiç darbesiyle açmak zarar verebilir mandreni içindeki sola doğru açılan ters paso civatayı nasıl torklu somun sökme ile açtıysanız manrenide araya cıvata sökme uçla iki matkabı birleştirip çok rahat sökebilirsiniz Allen ve çekiç sağlıklı değil
@@ErCanEverything I admire your repair skills. Of course I always make every repair attempt. But with parts being so overpriced there is almost no repair business anymore .
I also have this drill, but I was not able to remove the chuck. I tried the same method with an Allen key but without any luck. I was afraid I might destroy it completely, so in the end, I just removed all the screws, split the plastic case as much as possible, and removed the control board. Then I desoldered the wires from the motor and repaired the board. I replaced all the MOSFETs (just to be sure). I bought them from TME, and they look different than yours...
After the repair, I soldered the board back to the motor wires, covered it with silicon, and put it all together. The drill now works without any problems. A review from "AllHandmade" shows how to take it apart.
Complimenti amico mio, un lavoro eccezionale di elettronica e meccanica, usando semplicemente la continuità è un paio di pinzette. Bravissimo
I really like these tweezers.❤️
I’ve had this drill for a while, and the stall issue is so frustrating! Excited to see the solution to this problem.
Greetings, my friend. I don't understand how you soldered all the pins together like that in the mosfet?
Incredible fix, great job! I hate this design where you have to take the chuck out, to take apart the drill. Einhell also does this on some of their drill and it is really a terrible design
Thank you my Friend🙂🤝
It's really a very bad design.🤦
well done the problem is tipe mosfet transistor!
Unbelievable!?! Only yesterday I spent an hour+ searching for any information how to take apart this exact model. Great job. Do you think we can find those bldc driver/controller boards from China?
I also searched a lot but couldn't find how to disassemble it. And I thought the chuck had to be removed first. I don't think you'll find the same controller, except for some poor quality controller
This qas probably still under warranty, but good to see you fix it. Also you might want to look into alternative for mosfets becausr alpha&omega semiconductor ones are kinda crap.
Toujours au top l ami !
If I could put 1000 thumbs up I would most certainly do.
Thank you my Friend 🙏🙂🤝❤️
Professional repair! 👏
Thank you Brother🙏🙂🤝❤️
@@ErCanEverythingtodo muy bien y otras reparaciones también, a ver para cuando una reparación de sierra circular de esta marca que cortó bien unos 20 metros de tablero de aglomerado de 10mm y ya no sale ningún corte bien, sierra nueva, disco de sierra nuevo, no se a golpeado ni se a caído, probé a apretar y o aflojar tornillos y sigue igual 😢, saludos desde iberia
Simply PRO 👌🏼
Well done my friend!
Finaly a solution for my problem . I would like to know what are those little chips and where can i buy them. And my drill chuck is holding on so tight i cant get it off but i will try
I also left links to the transistors in the description. It is very difficult to remove the chuck, I have one that I did not manage to remove. There is a possibility that you will damage the gearbox. Otherwise, if it worked, it would be easier and always try in first gear.
addressing this drill issue clearly
WAO VERY GOOD 👍❤️🤪
Thanks for useful video sharing
I was wondering if you know why most of the problems with Parkside brushless lineup are mosfets?
Poor quality MosFET or wrong calculation🤷
Cześć zrobiłem tak samo jak Ty ale moja wkrętarka nie działa dalej mruga niebieska dioda co może być jeszcze przyczyną
Wonderful!
Allen anahtarla açtığın mandreni öyle çekiç darbesiyle açmak zarar verebilir mandreni içindeki sola doğru açılan ters paso civatayı nasıl torklu somun sökme ile açtıysanız manrenide araya cıvata sökme uçla iki matkabı birleştirip çok rahat sökebilirsiniz Allen ve çekiç sağlıklı değil
Pro so thanks fo this video ❤
Saludos y muchas bendiciones para todos ❤❤😊😊😮😮
Thank you my Friend🙂🤝
Toujours et toujours ce panneaux de commande de mauvaise qualité 😢
🤦🤷
❤❤❤
This is my first time i see PARKSIDE using sensored BLDC motor. I thought they alway using sensorless motor for all purpose.
They are available in several models and most impacts also have sensors.
Quel galère a démonter 😱
🤦🤦🤦
@@ErCanEverythingc'est impressionnant faut la démonter entièrement
There is no other option but I wanted to clean the gearbox too❤️
👋👋❤️❤️👋👋
👋👋👋🙂🤝
Супер
Would have bought a new one, swapped controllers and returned for money refund!
I can't do this💔
@@ErCanEverything I admire your repair skills. Of course I always make every repair attempt. But with parts being so overpriced there is almost no repair business anymore .
Eh!!😅