1. Original is alluminium disc. 2. This disc have electrostatic charge (negativ or positiv) 3. Central disc is connected to tesla coil. 4. On the top you must put piezo...
5. a cockcroft walton multiplier as to be connect to both rotativ disc with brushs 6. 3 differents frequency are involved,witche means 3 pots ajustments has to be use... incresing speed of the 2 disc is absolutly not the point: speed rotation has strictly nothing to see into that,only count the synchronisation of thoses 3 frequency, in order to find out resonnance of the entire set up,brushless motor are definitly useless here,alexey chekurkov used only 12VDC fan to run the 2 disc in rotation,discs are sticked on thoses fan,no more....
1.) Too much distance between the disc and aluminum sheet. 2.) Aluminum sheet is too thin. You need atleast 2 inch thick for stronger effect. 3.) Install Ultrasonic Emitter Drive up top facing downwards to prevent the magnetic field from going outwards. The UED will help control the EMF to make an upward force. 4.) Atleast 10,000 RPM is enough. 5.) Disc setup should spin in opposite directions.
So Proud Of You, Buddy🤕 You're doing something Extraordinary in your life🤍❤ Great inventions are always a result of experimentation mindset. KEEP IT UP
A theory I have is that in between the magnets the plates one needs to be positively charged in the other one negatively charged. As the magnetic fields are spinning this may create lift, I don't know, but I've seen a couple other experiments regarding this setup and I've seen that a person has one plate up on top that is positively charged and one in between that is probably negatively charged but I'm not sure.
Several years ago, a video was shut down after 1 month. It was dealing with demonstration of thermocouple / thermopile that slightly loses weight when activated, and also on sensitive digital weigh scale. Heat must be released away from mass so as not expanding air pressure under unit in test pushing upward . (upside down) The word "correlation" describes other experimenters who successfully aborted gravity with their specialized set ups using matched metals according to ratios of properties. See 1800's work of John W. Keely with his "transmitters" as in series junctions of silver, gold, and platinum thermopiles as tested for gravity control with his array of tuning forks vibrators. The nodes junctions multiplied the frequencies even higher causing dissonance to normal orderly gravity waves. A french scientist also lifted an open frame dirigible with sandwich plates at either end hooked to frequency transmitter. (translated from french) It seems there are other ways to disrupt gravity waves affecting mass..
@@waterfuel E=(a+b+c=x) T/M M=(a+b+c=x) -TM Face noising is what makes this hard and difficult. a,b,c =alpha, beta gamma. T=time, M=matter. Back to words. The three radiation emission packets of alpha, beta and gamma are the a,b,c, values, the "decay bundle" is the x value. The Lyman Alpha Line Split is the reverse POV value of the X-ray radiation spectrum, and the .003 angstrom difference is our EYES, and it is also Euler's Constant in the brain. Integrated Information Theory uses three brain wave angles to identify the Phi value of a subject as conscious. It ALSO applies the the Earth in the math model PERFECTLY.
Of course you know that Philadelphia machinist and musician John Keely did several antigravity demonstrations in the late 1800's. He used what we now call thermocouples and thermopiles sending high frequency vibrations of certain inharmonic ratios down the transmitter wires to mass. The nodes create upper harmonic multiple frequencies.A different set up of his used 3 spinning air pressure forced sirens at differing ratio tones that levitated, then set back down, - about 1 ton. He also lifted his 2 ton steel sphere high pressure tank with tuning forks array and the special AG, Au, and PT wires. Signed affidavits were made of those present at the time. Keely And His Discoveries. The Mass is still there. The gravity waves are interfered with. Keely got his Earth frequency/harmonic from Tesla. Tesla didn't like Keely since Keely received more investors money than he did. A French scientist did similar set up with open frame dirigible with sandwitched differing metal plates at both ends. The high frequemncy oscillators hooked by wires to the plates. Whole unit lifted. Propulsion forward was done with mounted engine and large fan moving the weightless machine. See also Russian Grebenikof data on his cavity resonators of microwave frequencies made into stand plartform that he flew around, and photo was in local newspapers. He mounted handle bar controlled cables 4 gimbols on board 4 corners with high voltage electrostatic field in vicinity of the beetle wings on the 4 unfolding vanes. ( like 4 chinese fans) The main switch turned on a car coil and hooked to aluminum sheet array.(Think about the actual pores on a cd disc,- Beetle wings somewhat similar but hexagonal pores.) Certain beetles fly with gravity control, except when air is damp wet,- no electrostatics on their wings.
The problem with that method is if used for any significant amount of time at forces high enough to achieve lift then that aluminum disc eventually gonna glow red hot and then yellow and then melt into lava.
Your heading in the right direction; the spinning field must be slamming against the magnetic field in opposite directions ; i.e North | North or South | South ; your rotors ripped apart more so by Centrifugal forces; the Tesla coil that Alex C. used pushed an expansion of the static field outward to engulf the model; the piezo pulser created the downward undulation of the ethers that moved the model upwards. He had to find a timing resonance that could undulate with the gravity negating field to create a downward pressure with the field that was undulating from the Tesla modified counter berry that the opposing magnetic fields were producing. With only magnets alone you would effect stationary weight reduction to a particular degree. . You can test this by putting similar volume / sized magnets N/S south together and another pair as a N/N or S/S in your other hand, you would notice a slight weight reduction. If you created a new model and attached a Tesla 'Hairpin' / Stout Bar lead / cold Radiant Charge to the central deflector and had sufficient capacitance developing in the surrounding air coupled to a piezo electric ultra sonic emitter. You should with enough tuning of the system get the craft to hover. You do not need to cycle the magnets at 13000RPM to produce the effect. Control your variables and you should be able to create low altitude lift this way. 'Let us hear the conclusion of the whole matter; Fear [Yahwah] God and keep the commandments: for this is the whole duty of man.' Ecc. 12:13
Dude you forgot to apply super high voltage in the middle plate, and to mention he added two of those with a gap between, try playing around with the polarity, for instance try negative on the top plate and positive on the bottom one..
i did not expect that, but then i thought the bldc motors are too powerfull for this device, simple dc brushed 6-12 volts should do and the middle disc needs to be charged to create electrostatic field. the device also requires a high voltage source, perhaps a MOT or step up transformer and a tesla coil, however im not sure the tesla coil is required, according to Alexey Cherkikov the spinning discs must be a specific gradient nickle nano coated alluminum if im not mistaken, there might be a couple of other items im unsure of, but the experiment will go alot smoother after those items..still and all awesome experiment i got a real kick out of it, pun intended..keep it up! Good luck..cheers
The alexey chekurkov device has two counter-rotating aluminum discs. Cannot be steel. Must be diamagnetic. Aluminum only. Counter-rotating with high voltage positive on the top plate and high voltage negative on the bottom plate as well as magnets on the bottom plate only. Also, high voltage AC on the central plate between the positive and negative plate, not moving, stationary. And your magnets Must ALL point in the same direction. You must try North up and if not, try South up.
I tried using cone shape aluminum using a router, 28,000 RPM, with fixed neodymium circling aluminum cone hoping an imbalance shaped field would provide some forward motion. Nothing I could see before it broke up.
Keep at it, it took a 1000 tries to make a light bulb. I had this same idea. But the reason I never made it yet is because I believe you need carbon fiber - at the very least - to build something with the strength to weight radio. I actually have a design for something a little better than just carbon fiber too, bad sadly there are NO 3D printers that use it as it doesn't exist yet in reality, so I'm trying to build a 3D printer to do it if you wanted to collaborate?
this type of video regarding anti gravity has been obscured til recently and I've noticed conspiracy and future tech vids from 10 yrs or so ago around 70-% am unable to locate. convenient
I have been doing this but using multiple axis which are spinning, all weigh the same and rotate in sync. you also need a means then to shift the weight in order for the device to off balance, move and then recenter itself. Nice work on a linear plane notion for sure, I like this development :D
He used to many magnets we which were all creating multiple streams of Utrons that blew the thing apart. 2 solid magnets (1 on top one on the bottom) should do the trick. Have an apparatus that can tilt it and you can steer it
Nobody understands math. What are you defining with the magnets in space? A current sheet, in a linear harmonic series, on a disc. This is a counterspatial centrifuge. Look at Euler's coin. Nobody knows what sinusoidal in math means either. Tesla's been dead for a while now.
Thanks! I hope so too. It would be a bummer if it's an altered video and fake... but I will keep posting my findings and experiments. Hopefully I can get something working based on Alexey's experiments.
@@Guineapixel-page It is real. Building it myself. 85% complete. Have all generators and testing equipment. Try this source, been using for over 30 years: www.amazing1.com
I searched this on youtube after listening to Whitley Strieber's book Communion. Something in there about people trying to make antigravity devices with counterrotating magnets.
This is definitely a worthwhile build puzzle. My digital scale displayed - 0.20oz repeatedly . No Tesla coil or ultrasonic circuit on my replication yet.
Think about Earths magnetic field. It's 0.00003 Tesla. Think about force on a wire and think about Faradays Law of induction. F=BIL F= 0.00003 x 1amp (e.g.) x 2m (e.g.) F = 0.00006N - Not alot. Until you add velocity or change of flux; Faradays law. Might be a good direction for you :)
You designed it wrong. 1) Put the aluminum disc on the very bottom and make it half the size it is now. 2) Get rid of the spinning magnets and replace them with a high voltage, low current pulsed DC power supply and apply that power to the aluminum plate. 3) Replace the conductive metal screws holding the frame with 3D printed carbon fiber rods. 4) Add a saucer shaped copper top plate on top that is 2X the size of the aluminum bottom plate and sandwich them together. 5) Connect the top copper plate as the positive anode to the bottom aluminum plate cathode and use high voltage and pulse it to get it to lift off the table. 6) Don’t shock yourself and be careful.
Looks like there is a reason for specific rotational speeds (2500/3600rpm) after all. It's not antigravity as such and there's more to it than just magnetic fields.
Once you designed it a little bit more sturdily have you tried placing these desks much closer together? Have you tried them in repulsion facing each other at close range?
There is an interesting design of aircraft, but they rarely talk about it, because this thing is secret. The topic of pulsed plasma thrusters has been developed since the early 60s (see PPT - Pulsed plasma thruster) - they are usually designed for spacecraft. But we will talk about a little-known design - these are plasma propulsion panels for aircraft, where the same Pulsed plasma thruster, but reduced to the size of a pencil and stacked in the form of cells in the panel. The design resembles a conventional plasma TV screen, where there are also discharge cells that activate the glow of pixels on the screen. And plasma propulsion panels have long discharge cells, the arrester has a railgun architecture (just rail contacts or coaxial), and the ionized discharge air is accelerated there by the Lorentz force to enormous speeds - a kind of ramjet engine is obtained. Just imagine! - tens of thousands of small ramjet engines assembled in a panel and firing plasma synchronously with a huge frequency (hundreds of kilohertz). Thus, plasma propulsion panels create lift by pulsed emission of plasma jets from railgun cells. There are tens of thousands of cells in the panel, they shoot at a frequency of hundreds of kilohertz, a huge pulse is obtained, and the plasma swirls the air into toroidal rings - the aircraft is held on this air cushion. Horizontal acceleration is created by the same plasma panels on the sides of the device (they glow, from the side they look like "portholes"). Such devices like "triangle" or "disk" have been observed for a long time, they are mistaken for alien ones - but these are terrestrial devices. They are classified and used for espionage and secret actions. Pulsed electromagnetic technology generates microwave radiation, therefore it is harmful to health. They rarely fly - only military missions. Therefore, they are not suitable for a citizen. This maintained the secrecy. Now they are already declassifying - many people know about this secret technique. When declassified, they will be used for cargo airships. But there is a danger that they are now going to be adapted to deliver small nuclear charges to decision-making centers - such means of delivery are not specified anywhere, are not conventional. This lowers the threshold for starting a war. It would be necessary to declassify them as soon as possible. That's why I'm writing about it. However, I have written before - starting with the book "The Elimination of UFOs" and many articles. There are also videos on my TH-cam channel - "Declassified UFO" and "UFO Anatomy".
Drives are not balanced. Therefore, there was a vibration due to the resulting precession. You need a good balance. The discs must rotate at the same speed synchronously. In order for the material of the disks not to be destroyed by centrifugal force, it must be covered with a shell of steel and carbon fiber.
The rotating discs are too far apart from the non-rotating metal disc in between them, and thus not inducing the Eddy currents. I'm thinking the spinning magnets (top disc spins in opposite direction of bottom disc) are inducing Eddy currents in the non-rotating disc, and somehow the combination of Eddy currents from both magnetic discs is causing lift.
You are right they are rotating on the same direction and the aluminum sheet is the wrong material also the metal sheet have to have a frequency apply to it at 500khz the speed of the turning plates is only 300 to 800 rpm to lift off .1500 rpm to travel in straight line .by changing the frequency on the center metal plate the lift increase or decrease. To move forward or back you push electrons over a coil .
If you want to go faster you will need a stronger motor like the supernova 2207 by AOSRC and you will need a metal disk in order for it not to explode. The center sheet metal circle is to far from the magnets because magnets are subject to the inverse square law. Fall Foreward Research uses a ultrasonic emitter drive on top and connects the center stationary disk to a tesla coil.
Make the plates holding the magnets into an inch tube made of superdunductive material made inthe neodymium magnet bearing ball that would go in tubes in with tight clearance. Add exciters at 4 points on the tube so the magnet spins. Then slowly spin plates against each other. The hardest part is keeping the magnets at a supercooled temp.
Top motor and bottom motor must spin in opposite directions. You should connect the device to a Tesla coil to create an electrostatic charge. You must generate high voltage an connect the positive to the top and negative to the bottom. You must generate microwave on the to with piezoelectric device. All this create an antigravity structure or device that can levitate...
UFO's are circular for a reason. The magnets inside the hull are laid out in circular fashion. They are static... they don't spin. The key is in the polarization. In the Bermuda Triangle, they would break compasses (in the sailing vessels) fearing that we would use more than one bar magnet and fly like they do. You have to do something to get the magnets attention... high voltage. Lightning will work.
You could try replacing the Tesla coil with a HV tazer, then match the atmospheric resonance using a feedback loop using mics and speakers, you don't need so many revs I believe if you do this and it will all fit on board, plus you could implement a portable function generator to define exactly which frequencies you want, you could do all this with a 12v battery, just increase the scale of your model and try this.. let me know your thoughts please.
Instead of a metal plane in the center, I think you need to have 2 metal domes, so you have 2 opposing asymmetric magnetic pulsing fields hitting each other. See the principle behind Dr Salvatore Pais; "Pais Effect"
It was such a huge magnetic field created that the holding structure doesn't hold it in its place. Maybe the ideia is right, but the means doesn't. Did you already think that if you realize how the magnetic field was, you can handle the position proper invertion in order to direct the field to the right direction, which is above the structure. Also, you might wanna to considered that small magnetic fields doesn't work well is you don't apply some higher amperage voltage in order to have some ruptures in the field structure as it is formed usually.
This was a successful test as we learned it produced force strong enough to rip the craft apart, if you manage to control this force correctly, Good chance it will fly
I had successfully tested in 2011..please understand one thing..gravity waves has constant waves and your prototype must be light weight than apply electro static charge and gap must be 6 inch between ground (earth) and prototype. ..
Apparently the graviflyer uses some kind of special metal for the middle large plate. What metal did you use? Apparently it’s a type of aluminium called “stucco metal”
you need to charge center disk with 12kv and both rotating disks with 400v via copper sheet/brush. the magnets don't do much except push the EMF field to the center creating an earth like electrostatic field. the original creator actually didn't even put magnets on the top disk in his successful build reaching 10 feet in the air when powered on. good try though.
instead of motors. maybe a better approach is to use two Tesla "Columbus Egg" coils spinning on opposite directions. No moving parts that fly off that way, It would just be magnetic fields spinning. If this does bend space-time or flatten it, then it might lift or be very easy to lift. I am a little worried that sticking your hand into such fields might be a mistake. Poke a stick in first. Also, would light be influenced by this. You also want the coils to be given the exact resonance frequency they take. "Tuned".
Next time, use 1 disk, magnets on the bottom. Put the motor above it and put a high mu metal between the disk and the motor and across the whole top to keep the B field concentrated below the disk. You will see it literally fly if you put a copper plate on the table below it! You will need to tie it off to the walls so the chassis doesn't rotate once it lifts off. If you do this with the B field concentrated on one side, I expect you will see some significant weight loss or propulsion. This design of yours had too much symmetry to lift.
I call it a failed success although the concept could be applicable but the dimensions of the materials used in the experiment were not planned and the magnets were not arranged in an hallbach array, plus the fixed aluminum sheet fluttered like paper in air so the eddy current pattern was out of phase causing it to vibrate more thus to eventual doom.. Anyways it was a great effort
try adding voltage to shield around object and aluminum plate. also make aluminum surface rough or uneven with small dimples plate must have voltage added try this and less speed
Welp, Looks like you really took your time measuring everything out and centering it etc, probably with enthusiastic energy just to watch all your work explode from centrifugal forces, lol. Gonna make another one? I can imagine Stewy on Family guy going “have a little explosion there? Hm? A little, a little explosion? Hm? Explosion? Next time at least embed the magnets into sunken holes, with North Pole outwards and south poles inwards with an outer rotor, counter rotation is optional with a much small gap between.
Guinea Pixel just wanted you to know we were only being facetious in the previous comment. We have been known to take on human humor. We fully support your intentions to achieve vertical acceleration without an upwards force as well as the human condition. Will try to help in certain aspects. Good luck.
Nice surf guitar. OK, not so fast next time. Don't go for full levitation, just put the whole works on a large, sensitive scale and see if the the weight drop.
Why not a sphere spinning forward instead on sideways Dyson sipping all sides with intense fusion such as Mercury element thermal magnetic conductivity
You did it wrong. You’ve setup 2 magnetica wheel that where pushing force opposite each other, so it didn’t levitated. You should try to don’t instal the bottom wheel and leave just the only one on the top, then the magnets who’ll push force down and make your spaceship levitating
you have used derlin/PTFE material for magnets, It wont work. Well you miss high voltage supply for the center disc, and ultrasonic sound on top and bottom side. Probable you know it wont work.
Gravity does not push or pull... it merely instructs/commands matter. Matter is self propelled. comprehend that and you are on the right track; and you will know how the reptilians moved the earth from the 5th orbit down to the 3rd orbit.
Chekurkov setup and looks nice just need more of tesla hv ,Van de graf and piezoelectric or ultrasound on top where is wave of piezo same diameter as device goodluck..Thanks for nice setup
your rpm is way to high. i dont believe the rpm needs to be so high. count how many times a single magnet passes another. what is the freq of the passing? increse the amount of magnets for higher interactions... rather then increase the speed. the effect can be slid past as it does not have time to have an effect. i suspect it to be around no less then 150 and no higher then 2500... increasing speed breaks down the symatics to a finer pattern... many different approaches and speeds can be used .. i hope this helps :)
I'm no expert but why do you need two spinning discs? It seemed to me almost like the device was producing thrust on both sides and may have been the reason why it broke apart because it was literally pulling itself apart. I tried to slow down the moment of failure to see what happened but it was too fast. The only failure is the one you don't learn anything from.
I'm thinking that your machine had maybe a mm of lift, but much more torque effect. Unless you want everyone to see your explosive mishap, you might consider editing first.
Во первых диски вращались в одну сторону, а необходимо разностороннее вращение с определённой скоростью, Во вторых импульсы высокого напряжения и малых токов необходимо так же регулировать до оптимальных, В третьих, ультразвуковые частоты разнонаправленные и в резонанс отсутствуют...Вы просто угробили аппарат бесконтрольным ускорением вращения до центробежных сил, которые разрушили конструкцию...это не эксперимент, а халтура!
Alexey built an electronics packet, which he graciously revealed in one of his log entries. The electronic packet may have been under the chrome top. He spoke it all in cyrillic, or something. I wish that I could offer more help. Where is your tesla coil?
![ร้อยพ่อพันแม่ - WanMai [Official MV]](http://i.ytimg.com/vi/XY2pNYASEbg/mqdefault.jpg)
¿You're still alive?
1. Original is alluminium disc.
2. This disc have electrostatic charge (negativ or positiv)
3. Central disc is connected to tesla coil.
4. On the top you must put piezo...
5. a cockcroft walton multiplier as to be connect to both rotativ disc with brushs
6. 3 differents frequency are involved,witche means 3 pots ajustments has to be use...
incresing speed of the 2 disc is absolutly not the point: speed rotation has strictly nothing to see into that,only count the synchronisation of thoses 3 frequency, in order to find out resonnance of the entire set up,brushless motor are definitly useless here,alexey chekurkov used only 12VDC fan to run the 2 disc in rotation,discs are sticked on thoses fan,no more....
1.) Too much distance between the disc and aluminum sheet.
2.) Aluminum sheet is too thin. You need atleast 2 inch thick for stronger effect.
3.) Install Ultrasonic Emitter Drive up top facing downwards to prevent the magnetic field from going outwards. The UED will help control the EMF to make an upward force.
4.) Atleast 10,000 RPM is enough.
5.) Disc setup should spin in opposite directions.
@@par4tech have any referenfeces? I would like to know
@@dogodogo5891 elon musk
I see the magnets were attracted. I would like to see this experiment with them opposing.
Alexey Chekurkov's videos can all be auto translated into english by the way if you really want to understand how it works
So Proud Of You, Buddy🤕 You're doing something Extraordinary in your life🤍❤ Great inventions are always a result of experimentation mindset. KEEP IT UP
A theory I have is that in between the magnets the plates one needs to be positively charged in the other one negatively charged. As the magnetic fields are spinning this may create lift, I don't know, but I've seen a couple other experiments regarding this setup and I've seen that a person has one plate up on top that is positively charged and one in between that is probably negatively charged but I'm not sure.
iThinkItCanBeHighVoltageAc,InsteadOfDc.
Several years ago, a video was shut down after 1 month. It was dealing
with demonstration of thermocouple / thermopile that slightly loses
weight when activated, and also on sensitive digital weigh scale. Heat
must be released away from mass so as not expanding air pressure under
unit in test pushing upward . (upside down) The word "correlation"
describes other experimenters who successfully aborted gravity with
their specialized set ups using matched metals according to ratios of
properties. See 1800's work of John W. Keely with his "transmitters" as
in series junctions of silver, gold, and platinum thermopiles as
tested for gravity control with his array of tuning forks vibrators.
The nodes junctions multiplied the frequencies even higher causing
dissonance to normal orderly gravity waves. A french scientist also
lifted an open frame dirigible with sandwich plates at either end hooked
to frequency transmitter. (translated from french) It seems there are
other ways to disrupt gravity waves affecting mass..
Mass reduction. I think backwards.
Not mass reduction . Gravity pulling waves nullified with high frequency vibrations applied.
@@waterfuel
E=(a+b+c=x) T/M
M=(a+b+c=x) -TM
Face noising is what makes this hard and difficult. a,b,c =alpha, beta gamma. T=time, M=matter.
Back to words. The three radiation emission packets of alpha, beta and gamma are the a,b,c, values, the "decay bundle" is the x value. The Lyman Alpha Line Split is the reverse POV value of the X-ray radiation spectrum, and the .003 angstrom difference is our EYES, and it is also Euler's Constant in the brain. Integrated Information Theory uses three brain wave angles to identify the Phi value of a subject as conscious. It ALSO applies the the Earth in the math model PERFECTLY.
Of course you know that Philadelphia machinist and musician John Keely did several antigravity demonstrations in the late 1800's. He used what we now call thermocouples and thermopiles sending high frequency vibrations of certain inharmonic ratios down the transmitter wires to mass. The nodes create upper harmonic multiple frequencies.A different set up of his used 3 spinning air pressure forced sirens at differing ratio tones that levitated, then set back down, - about 1 ton. He also lifted his 2 ton steel sphere high pressure tank with tuning forks array and the special AG, Au, and PT wires. Signed affidavits were made of those present at the time. Keely And His Discoveries. The Mass is still there. The gravity waves are interfered with. Keely got his Earth frequency/harmonic from Tesla. Tesla didn't like Keely since Keely received more investors money than he did.
A French scientist did similar set up with open frame dirigible with sandwitched differing metal plates at both ends. The high frequemncy oscillators hooked by wires to the plates. Whole unit lifted. Propulsion forward was done with mounted engine and large fan moving the weightless machine.
See also Russian Grebenikof data on his cavity resonators of microwave frequencies made into stand plartform that he flew around, and photo was in local newspapers. He mounted handle bar controlled cables 4 gimbols on board 4 corners with high voltage electrostatic field in vicinity of the beetle wings on the 4 unfolding vanes. ( like 4 chinese fans) The main switch turned on a car coil and hooked to aluminum sheet array.(Think about the actual pores on a cd disc,- Beetle wings somewhat similar but hexagonal pores.) Certain beetles fly with gravity control, except when air is damp wet,- no electrostatics on their wings.
@@waterfuel Tl;DR. I saw the word "inharmonic" and I know the rest is right.
Nice experiments! 1:25 looks like those photos of the Roswell "weather balloon" lol
I love your out of the box thinking. Keep that up.
The problem with that method is if used for any significant amount of time at forces high enough to achieve lift then that aluminum disc eventually gonna glow red hot and then yellow and then melt into lava.
Your heading in the right direction; the spinning field must be slamming against the magnetic field in opposite directions ; i.e North | North or South | South ; your rotors ripped apart more so by Centrifugal forces; the Tesla coil that Alex C. used pushed an expansion of the static field outward to engulf the model; the piezo pulser created the downward undulation of the ethers that moved the model upwards. He had to find a timing resonance that could undulate with the gravity negating field to create a downward pressure with the field that was undulating from the Tesla modified counter berry that the opposing magnetic fields were producing. With only magnets alone you would effect stationary weight reduction to a particular degree. . You can test this by putting similar volume / sized magnets N/S south together and another pair as a N/N or S/S in your other hand, you would notice a slight weight reduction. If you created a new model and attached a Tesla 'Hairpin' / Stout Bar lead / cold Radiant Charge to the central deflector and had sufficient capacitance developing in the surrounding air coupled to a piezo electric ultra sonic emitter. You should with enough tuning of the system get the craft to hover. You do not need to cycle the magnets at 13000RPM to produce the effect. Control your variables and you should be able to create low altitude lift this way. 'Let us hear the conclusion of the whole matter; Fear [Yahwah] God and keep the commandments: for this is the whole duty of man.' Ecc. 12:13
EXCELENTE EXPLICACION , DISCULPA PODRIAS COMPARTIR TUS PLANOS AMIGO
You know so much bro and you have any experience fabricated by you.
That was great other than the Yahweh part
Dude you forgot to apply super high voltage in the middle plate, and to mention he added two of those with a gap between, try playing around with the polarity, for instance try negative on the top plate and positive on the bottom one..
i did not expect that, but then i thought the bldc motors are too powerfull for this device, simple dc brushed 6-12 volts should do and the middle disc needs to be charged to create electrostatic field. the device also requires a high voltage source, perhaps a MOT or step up transformer and a tesla coil, however im not sure the tesla coil is required, according to Alexey Cherkikov the spinning discs must be a specific gradient nickle nano coated alluminum if im not mistaken, there might be a couple of other items im unsure of, but the experiment will go alot smoother after those items..still and all awesome experiment i got a real kick out of it, pun intended..keep it up! Good luck..cheers
The alexey chekurkov device has two counter-rotating aluminum discs. Cannot be steel. Must be diamagnetic. Aluminum only. Counter-rotating with high voltage positive on the top plate and high voltage negative on the bottom plate as well as magnets on the bottom plate only. Also, high voltage AC on the central plate between the positive and negative plate, not moving, stationary. And your magnets Must ALL point in the same direction. You must try North up and if not, try South up.
I tried using cone shape aluminum using a router, 28,000 RPM, with fixed neodymium circling aluminum cone hoping an imbalance shaped field would provide some forward motion. Nothing I could see before it broke up.
All a hovering propeller needs for forward motion is gyroscopic tilt.
Yes....Super AntiGravity...Build another...you must be at 36,543rpm
Lmfao the metal plates were too far apart from eachother. Do it again with more power
Keep at it, it took a 1000 tries to make a light bulb. I had this same idea. But the reason I never made it yet is because I believe you need carbon fiber - at the very least - to build something with the strength to weight radio. I actually have a design for something a little better than just carbon fiber too, bad sadly there are NO 3D printers that use it as it doesn't exist yet in reality, so I'm trying to build a 3D printer to do it if you wanted to collaborate?
Thanks Peter, please email me at info@guinea-pixel.com
@@Guineapixel-page Are tired of being stuck on this planet? Should I email you?
this type of video regarding anti gravity has been obscured til recently and I've noticed conspiracy and future tech vids from 10 yrs or so ago around 70-% am unable to locate. convenient
I have been doing this but using multiple axis which are spinning, all weigh the same and rotate in sync. you also need a means then to shift the weight in order for the device to off balance, move and then recenter itself. Nice work on a linear plane notion for sure, I like this development :D
He used to many magnets we which were all creating multiple streams of Utrons that blew the thing apart. 2 solid magnets (1 on top one on the bottom) should do the trick. Have an apparatus that can tilt it and you can steer it
Nobody understands math. What are you defining with the magnets in space? A current sheet, in a linear harmonic series, on a disc. This is a counterspatial centrifuge. Look at Euler's coin. Nobody knows what sinusoidal in math means either. Tesla's been dead for a while now.
Good luck I hope this technology is for real. If so I wouldn't mind building one myself. This could change space travel forever.
Thanks! I hope so too. It would be a bummer if it's an altered video and fake... but I will keep posting my findings and experiments. Hopefully I can get something working based on Alexey's experiments.
@@Guineapixel-page It is real. Building it myself. 85% complete. Have all generators and testing equipment. Try this source, been using for over 30 years: www.amazing1.com
@@Beamshipcaptain Hey, did it work? It's been 5 months since your comment.
@@frostimator6870 Testing now. Having high-oltage bleed issues with the RC. Fixing now.
@@Beamshipcaptain any updates, I'm also looking into replicating the original model and would enjoy collaborating.
I searched this on youtube after listening to Whitley Strieber's book Communion.
Something in there about people trying to make antigravity devices with counterrotating magnets.
This is definitely a worthwhile build puzzle. My digital scale displayed - 0.20oz repeatedly . No Tesla coil or ultrasonic circuit on my replication yet.
Think about Earths magnetic field. It's 0.00003 Tesla. Think about force on a wire and think about Faradays Law of induction.
F=BIL F= 0.00003 x 1amp (e.g.) x 2m (e.g.)
F = 0.00006N - Not alot.
Until you add velocity or change of flux; Faradays law. Might be a good direction for you :)
Alexey uses a much lower RPM.
@@Red-Eyed_Black_Cave_Hamster No, ROTATION IS KEY. Review your basic physics, and tangential known devices, like Searl, OT Carr, Podkletnov, etc.
You designed it wrong. 1) Put the aluminum disc on the very bottom and make it half the size it is now. 2) Get rid of the spinning magnets and replace them with a high voltage, low current pulsed DC power supply and apply that power to the aluminum plate. 3) Replace the conductive metal screws holding the frame with 3D printed carbon fiber rods. 4) Add a saucer shaped copper top plate on top that is 2X the size of the aluminum bottom plate and sandwich them together. 5) Connect the top copper plate as the positive anode to the bottom aluminum plate cathode and use high voltage and pulse it to get it to lift off the table. 6) Don’t shock yourself and be careful.
the magnet would certainly repelled each other if they were counter rotating, especially if you increase velocity counter rotative spin.
Add a liquid mercury core
I think i saw the Swamp Gas escape just before the Rapid Unscheduled Deconstruction. There's your answer.
50 000 rpm...minimum brother...well done...keep it up.
Looks like there is a reason for specific rotational speeds (2500/3600rpm) after all. It's not antigravity as such and there's more to it than just magnetic fields.
Nothing like Alexey's machine
Once you designed it a little bit more sturdily have you tried placing these desks much closer together?
Have you tried them in repulsion facing each other at close range?
teleporting has been succsesfully.
There is an interesting design of aircraft, but they rarely talk about it, because this thing is secret. The topic of pulsed plasma thrusters has been developed since the early 60s (see PPT - Pulsed plasma thruster) - they are usually designed for spacecraft. But we will talk about a little-known design - these are plasma propulsion panels for aircraft, where the same Pulsed plasma thruster, but reduced to the size of a pencil and stacked in the form of cells in the panel. The design resembles a conventional plasma TV screen, where there are also discharge cells that activate the glow of pixels on the screen. And plasma propulsion panels have long discharge cells, the arrester has a railgun architecture (just rail contacts or coaxial), and the ionized discharge air is accelerated there by the Lorentz force to enormous speeds - a kind of ramjet engine is obtained. Just imagine! - tens of thousands of small ramjet engines assembled in a panel and firing plasma synchronously with a huge frequency (hundreds of kilohertz). Thus, plasma propulsion panels create lift by pulsed emission of plasma jets from railgun cells. There are tens of thousands of cells in the panel, they shoot at a frequency of hundreds of kilohertz, a huge pulse is obtained, and the plasma swirls the air into toroidal rings - the aircraft is held on this air cushion. Horizontal acceleration is created by the same plasma panels on the sides of the device (they glow, from the side they look like "portholes"). Such devices like "triangle" or "disk" have been observed for a long time, they are mistaken for alien ones - but these are terrestrial devices. They are classified and used for espionage and secret actions. Pulsed electromagnetic technology generates microwave radiation, therefore it is harmful to health. They rarely fly - only military missions. Therefore, they are not suitable for a citizen. This maintained the secrecy. Now they are already declassifying - many people know about this secret technique. When declassified, they will be used for cargo airships. But there is a danger that they are now going to be adapted to deliver small nuclear charges to decision-making centers - such means of delivery are not specified anywhere, are not conventional. This lowers the threshold for starting a war. It would be necessary to declassify them as soon as possible. That's why I'm writing about it. However, I have written before - starting with the book "The Elimination of UFOs" and many articles. There are also videos on my TH-cam channel - "Declassified UFO" and "UFO Anatomy".
Drives are not balanced. Therefore, there was a vibration due to the resulting precession. You need a good balance. The discs must rotate at the same speed synchronously. In order for the material of the disks not to be destroyed by centrifugal force, it must be covered with a shell of steel and carbon fiber.
The rotating discs are too far apart from the non-rotating metal disc in between them, and thus not inducing the Eddy currents. I'm thinking the spinning magnets (top disc spins in opposite direction of bottom disc) are inducing Eddy currents in the non-rotating disc, and somehow the combination of Eddy currents from both magnetic discs is causing lift.
2 disk should rotate opposite to each other
that’s really what made it explode
You are right they are rotating on the same direction and the aluminum sheet is the wrong material also the metal sheet have to have a frequency apply to it at 500khz the speed of the turning plates is only 300 to 800 rpm to lift off .1500 rpm to travel in straight line .by changing the frequency on the center metal plate the lift increase or decrease. To move forward or back you push electrons over a coil .
@@1miltondCan you please build one of these correctly yourself and document it?
Try using all aluminum plates and no neodymium mag on the upper metal. The stationary plate needs to be wider with a lip angling down.
If you want to go faster you will need a stronger motor like the supernova 2207 by AOSRC and you will need a metal disk in order for it not to explode. The center sheet metal circle is to far from the magnets because magnets are subject to the inverse square law. Fall Foreward Research uses a ultrasonic emitter drive on top and connects the center stationary disk to a tesla coil.
Make the plates holding the magnets into an inch tube made of superdunductive material made inthe neodymium magnet bearing ball that would go in tubes in with tight clearance. Add exciters at 4 points on the tube so the magnet spins. Then slowly spin plates against each other. The hardest part is keeping the magnets at a supercooled temp.
Top motor and bottom motor must spin in opposite directions.
You should connect the device to a Tesla coil to create an electrostatic charge.
You must generate high voltage an connect the positive to the top and negative to the bottom.
You must generate microwave on the to with piezoelectric device.
All this create an antigravity structure or device that can levitate...
UFO's are circular for a reason. The magnets inside the hull are laid out in circular fashion. They are static... they don't spin. The key is in the polarization. In the Bermuda Triangle, they would break compasses (in the sailing vessels) fearing that we would use more than one bar magnet and fly like they do. You have to do something to get the magnets attention... high voltage. Lightning will work.
You did well but the disks shoulf be made from expoxy and the magnets must be closer and oppose each other! Please try again.
And the alu disk should not be in between because this cancels the whole antigrav effect.
I have a dumb question instead using aluminum plate will a bismuth plate have any effects and to my understanding it’s diamagnetic to so ?
I can't really answer that, best is to probably do an experiment with a bismuth plate and see what happens.
You could try replacing the Tesla coil with a HV tazer, then match the atmospheric resonance using a feedback loop using mics and speakers, you don't need so many revs I believe if you do this and it will all fit on board, plus you could implement a portable function generator to define exactly which frequencies you want, you could do all this with a 12v battery, just increase the scale of your model and try this.. let me know your thoughts please.
Bro, with that many RPMs, you should have gotten to the ionosphere.
Instead of a metal plane in the center, I think you need to have 2 metal domes, so you have 2 opposing asymmetric magnetic pulsing fields hitting each other. See the principle behind Dr Salvatore Pais; "Pais Effect"
Good observation.
It was such a huge magnetic field created that the holding structure doesn't hold it in its place. Maybe the ideia is right, but the means doesn't. Did you already think that if you realize how the magnetic field was, you can handle the position proper invertion in order to direct the field to the right direction, which is above the structure.
Also, you might wanna to considered that small magnetic fields doesn't work well is you don't apply some higher amperage voltage in order to have some ruptures in the field structure as it is formed usually.
This was a successful test as we learned it produced force strong enough to rip the craft apart, if you manage to control this force correctly,
Good chance it will fly
Centrifugal force destroyed it. Nothing to do with it flying or attempting to.
I had successfully tested in 2011..please understand one thing..gravity waves has constant waves and your prototype must be light weight than apply electro static charge and gap must be 6 inch between ground (earth) and prototype. ..
You can't make an omelette without breaking some eggs.
Apparently the graviflyer uses some kind of special metal for the middle large plate. What metal did you use? Apparently it’s a type of aluminium called “stucco metal”
you need to charge center disk with 12kv and both rotating disks with 400v via copper sheet/brush. the magnets don't do much except push the EMF field to the center creating an earth like electrostatic field. the original creator actually didn't even put magnets on the top disk in his successful build reaching 10 feet in the air when powered on. good try though.
youll need a standard power source, a medium high voltage power source and a high voltage output tesla coil for center disk.
Can anybody explain me the reason of the aluminium sheet between two rotating structures?
I still can't understand how exactly is this working. I have looked these videos for 2 years now. Please explain.
instead of motors. maybe a better approach is to use two Tesla "Columbus Egg" coils spinning on opposite directions. No moving parts that fly off that way, It would just be magnetic fields spinning. If this does bend space-time or flatten it, then it might lift or be very easy to lift. I am a little worried that sticking your hand into such fields might be a mistake. Poke a stick in first. Also, would light be influenced by this. You also want the coils to be given the exact resonance frequency they take. "Tuned".
This happened at Roswell! We’ll get there!
Back to the drawing board!
Next time, use 1 disk, magnets on the bottom. Put the motor above it and put a high mu metal between the disk and the motor and across the whole top to keep the B field concentrated below the disk. You will see it literally fly if you put a copper plate on the table below it! You will need to tie it off to the walls so the chassis doesn't rotate once it lifts off. If you do this with the B field concentrated on one side, I expect you will see some significant weight loss or propulsion. This design of yours had too much symmetry to lift.
Nothing wrong with symmetry as long as you polarize the magnets correctly. Polarization is the key!
Maybe it is really working, this is why you plastic discs couldn't afford the sheer force and got broken
This video will look like the first model T video to our grandchildren 100 years from now😂
A little balancing never hurt anyone.
I call it a failed success although the concept could be applicable but the dimensions of the materials used in the experiment were not planned and the magnets were not arranged in an hallbach array, plus the fixed aluminum sheet fluttered like paper in air so the eddy current pattern was out of phase causing it to vibrate more thus to eventual doom.. Anyways it was a great effort
try adding voltage to shield around object and aluminum plate. also make aluminum surface rough or uneven with small dimples plate must have voltage added try this and less speed
Welp, Looks like you really took your time measuring everything out and centering it etc, probably with enthusiastic energy just to watch all your work explode from centrifugal forces, lol. Gonna make another one?
I can imagine Stewy on Family guy going “have a little explosion there? Hm? A little, a little explosion? Hm? Explosion?
Next time at least embed the magnets into sunken holes, with North Pole outwards and south poles inwards with an outer rotor, counter rotation is optional with a much small gap between.
Lol your Stewie comment :D yeah, will definitely do another one. Busy building a 5 axis CNC to create one with proper materials, avoiding PLA prints.
Guinea Pixel just wanted you to know we were only being facetious in the previous comment. We have been known to take on human humor.
We fully support your intentions to achieve vertical acceleration without an upwards force as well as the human condition. Will try to help in certain aspects. Good luck.
Great successful! Finally all parts was flying !....1:12....
Haha funny :)
@@Guineapixel-page If you need, is flying anything....always.....😂
Nice surf guitar. OK, not so fast next time. Don't go for full levitation, just put the whole works on a large, sensitive scale and see if the the weight drop.
Hello, can you share the design drawing?
Why not a sphere spinning forward instead on sideways Dyson sipping all sides with intense fusion such as Mercury element thermal magnetic conductivity
Do the magnets sit in the corect Position? North / South ? Do the Discs spin in the right direction ?
You did it wrong. You’ve setup 2 magnetica wheel that where pushing force opposite each other, so it didn’t levitated. You should try to don’t instal the bottom wheel and leave just the only one on the top, then the magnets who’ll push force down and make your spaceship levitating
you have used derlin/PTFE material for magnets, It wont work. Well you miss high voltage supply for the center disc, and ultrasonic sound on top and bottom side. Probable you know it wont work.
Would have been good. But you need to apply an HV to top and bottom plates to achieve electrogravitics..
Increasing velocity adds weight. Not subtract it.
Please try spinning each plate in the opposite direction to create a counter force.
Gravity does not push or pull... it merely instructs/commands matter. Matter is self propelled. comprehend that and you are on the right track; and you will know how the reptilians moved the earth from the 5th orbit down to the 3rd orbit.
@@TheBlueScarecrow hahahaha
Chekurkov setup and looks nice just need more of tesla hv ,Van de graf and piezoelectric or ultrasound on top where is wave of piezo same diameter as device goodluck..Thanks for nice setup
please post a new video
That explosion gave me a heart attack
hey u still there?
your rpm is way to high. i dont believe the rpm needs to be so high. count how many times a single magnet passes another. what is the freq of the passing? increse the amount of magnets for higher interactions... rather then increase the speed. the effect can be slid past as it does not have time to have an effect. i suspect it to be around no less then 150 and no higher then 2500... increasing speed breaks down the symatics to a finer pattern... many different approaches and speeds can be used .. i hope this helps :)
Pls Try again with Igor Staszak recepie!!!
You just invented a antigravy bombb. 😂😂😂
It's okay keep trying! Failure is actually the key to success
Right maybe he should replace all them materials that broke or got bent for stronger materials and maybe we'll see a lift. Lol
👍 experiment is a success. Gordon Freeman would be proud of you. Resonance cascade shows up from time to time.
Awesome design! I really think you are going in the right direction.
Hey chief could you post the 3D file for your design, I just bought a printer but I am unversed in model design, my printer is voxelab aquila thanks
The magnets should repel with north sides facing each other for the graviflyer model by that russian guy.
You forgot to put minute dents in the central plate
hello friend, you have perfect device, but you dont have high frecuency in the center disc, this its most important for gravity
That's not anti gravity. It rumbling around because of vibration and it just exploded because of high rpms
I'm no expert but why do you need two spinning discs? It seemed to me almost like the device was producing thrust on both sides and may have been the reason why it broke apart because it was literally pulling itself apart. I tried to slow down the moment of failure to see what happened but it was too fast. The only failure is the one you don't learn anything from.
Try another one my friend... im still wacthing you...
This is a nice machine. It is not Antigravity it is Antiproductivity. Put anying in it and it will break it. That is what it is.
these circles should turn counter-rotating
I'm thinking that your machine had maybe a mm of lift, but much more torque effect. Unless you want everyone to see your explosive mishap, you might consider editing first.
brushless rc motors..curious..how many amps are the esc's?
Во первых диски вращались в одну сторону, а необходимо разностороннее вращение с определённой скоростью,
Во вторых импульсы высокого напряжения и малых токов необходимо так же регулировать до оптимальных,
В третьих, ультразвуковые частоты разнонаправленные и в резонанс отсутствуют...Вы просто угробили аппарат бесконтрольным ускорением вращения до центробежных сил, которые разрушили конструкцию...это не эксперимент, а халтура!
Alexey built an electronics packet, which he graciously revealed in one of his log entries. The electronic packet may have been under the chrome top. He spoke it all in cyrillic, or something. I wish that I could offer more help. Where is your tesla coil?
What idea is behind of thi stuff?
Did the weight change? Were you able to neutralize it’s weight?
Matter has no weight except by virtue of the "Field".
When will be the expriment 2
Nice experiment, maybe try to remove the aluminium disc.