LQ4s are awesome. Loved my 1999 2500 with the 6.0l vortec. The 99-00 had the cast iron cylinder heads and certainly a great motor. Sold it to my buddy with 275k on the motor and he is still using the truck as a landscape work truck...probably close to 400k on the truck now.
I do the home made stifinners but also use them to route lines. Call them weight reduction holes, like in aircraft, Drop in grommets and you might not need to bolt any clamps/lines down. Clean look too and as you go you can make "panels" to cover the inner rails to help keep nature from damaging your vitals. Great video by the way.
I'm in the process of restomodding my 92 Suburban. Just yanked the 6.0 Vortec from a 2009 3500 van. Thanks for the video. I wanted to see how someone did an LS swap on a lifted squarebody. o7
Only made for 2-1/2yrs with the electronic speed sensor 89-1/2-91, NP241C passenger drop transfer cases are not easy to come by, it took me 15yrs to get hold of one for my truck unless you want to pay a small fortune for one! Advanced adapters has a great kit for adding the electronic speed sensor on the transmission then you could use a less expensive easier to come by transfer case.
@@trashbandit2449 It will have a round tag on it that says NP241C & it will also have the electronic speed sensor in the tail shaft with a passenger side drop.
don't be so sure. I come across them fairly often. Look at Craigslist for a part out... Ive sold several over the years for around $400-$600. but, that said, there are other TC's that could be easier, cheaper and more plentiful.
My 89 K5 Jimmy must be an earlier one cause it has the mechanical speedo in the NP241. I live in the rust belt were it's nearly impossible to find any K5's sitting rotted out. Most people sold that stuff off around here in recent years for scrap money.
K5LFE... 73's from K5MWA ! Nice K5. Mine's an 88. 14bsf govloc, 10b front w/tru-trac, 700r4 built with Monster Tr. parts, tan/blk raptor paint... etc...
Sounds like a cool setup! I wanted to convert my 10b to 8 lug and go 14 bolt, but found a Dana 60 in Colorado when there at a steal, so down the rabbit hole I went…….
@@carlsandvik2893 Oddly, I retained the 6 lug pattern, using axle shafts for the 14sf out of a 2000ish Express Van (with bigger lugs). That also let me do a brake conversion up front to H3 Hummer 4 piston calipers. No more seized floating calipers and stops like a cat on carpet 🙂. To fit the brakes I went to 17" Black Rhino Arsenal alloy wheels. 18" would have been better, but 17's have worked out ok.
Really looking forward to this series. I have an 89 K5 and my brother has a 91 we are looking to do some swaps on. Have either of y’all ever looked into using the Tejas motor mounts? Supposedly let you keep your factory transmission location, low mount AC, and stock oil pan. Seem to be used mainly in the 2wds but have heard of some success stories with 4wd as well.
Hey there. I already have the ORD cross member and motor mounts, so staying with those. Also, I want to keep as much up travel due to having high steer and a ram assist setup, so I went with the Holley 302-2 pan vs an ORD big block engine cross member (or other) to keep the stock pan. I already limited (bump stopped) my up travel due to my ram contacting the cross member at full stuff.
I've watched this video a dozen times. Finally ready to pull the trigger but maybe I missed it here but what do you use for a Transmission crossmember? I'll be going 5.3/4l60e/Np241c in a half ton K10 (1983).
curious what did he do with the ac/ heat system? like he went from factory to what? I notice the blue and yellow caps and was curious because I'd like to get the big box out of the engine bay on mine.
FYI....In AZ, it is almost impossible to find a NP241 with a passenger side drop. Craigslist, junk yards, Facebook market....no one has a unit. Now, you can get them off eBay but for $3800.00 which I refuse to do. Does anyone reading this thread know a good source or anyone wanting to sell one without me having to mortgage my home? 1978 Chevy Scottsdale is what I have running a 4L60e. Thanks!!!
Thanks! I don’t have a video, sorry. 2x3x0.25 wall tube with 1.75x0.180 round tube. Just a small angle up on the round tube. 2x2 runners to the frame and then I tied them to my a and b pillars for the cage. They’ve been working great.
On the 241c to LS LQ 4/9 will the older non 5 hole 241c tranny fit up to the LS, or is there an adapter needed for like the flex plate or another part for the geometry to work out? I have a 241c in my 1991 Burb I would like to use instead of sourcing another tranny. Appreciate the video, excited for this series as I am underway on the same build.
I have a 1975 and want to do a LS swap with a 6.0 engine and 4L65 trans with a NP241C case but, how do you deal with having the old transfer case axel on the left hand side to install this the NP241C on the right hand side? no one has mention that, thanks for your answer on advance.
Question. Will the LQ9 from a Hummer H2 work as a swap for a 72 Jimmy? Do you prefer the LQ4 or LQ9? For this vehicle? Is it possible to use the stock transfer case in the 72 with the LQ 4\9 if it comes with the transmission?
to be honest, these are super simple already. I mean you only really have like 7 sensors you need to run (MAP, TPS, Crank, Cam, O2, H2O, Oil).... you can hide the coil packs if you want clean and you have a super simple reliable system
Isn't that a driver's side drop with the independent front suspension? You would have to switch out your front axle at the minimum, maybe install a slip yoke eliminator driveshaft. Not sure. It would be more work than its worth.
Always wanted the 205 and front dig abilities along with rear lo only. Still have the electronic 261 from my burb, someone is going to want that 32 spline unit.
Hey what fuel sending unit did you use on your k5 LS builds? I’m trying to run my lines up drivers side and looking at videos and sites spectrum # Fg17b has come up. I ordered one but nothing lines up great…
1. I want the stock motor. I live in SoCal so I gotta pass smog. I am hoping to find a rebuildable core that might get me 250hp and still keep the stock computer happy. 2. I am looking for stock rear spring hangers (at the rear bumper). I swapped to ORD shackle flip hangers but I am going a different direction now and bringin it back down. If anybody has stock spring hangers, Let me know!
The old tbi 350 pulled so good at low rpm. Not fast, but a good truck engine. Im curious as to why you replace the crossmember, I've done a ton of these swaps, and never had a issue with this.
Me thinks that ORD might be a sponsor so he plugs their stuff when he can. Or he just does everything to the max. I take his suggestions as the best way to do things. I substitute when I can't afford the high end parts.
Did this guy say that you will alright in a chain driven transfer case ????😂😂😂😂😂 for what ? Going to the grocery store? Or pulling your boat from the boat ramp ? Must not be going too far off road .
Been waiting for this type of video my man! Thank you
79 k10 4x4 Short Bed 350 //700R4 // NP241
LQ4s are awesome. Loved my 1999 2500 with the 6.0l vortec. The 99-00 had the cast iron cylinder heads and certainly a great motor. Sold it to my buddy with 275k on the motor and he is still using the truck as a landscape work truck...probably close to 400k on the truck now.
I can't wait to see more videos of this project soon
My
I do the home made stifinners but also use them to route lines. Call them weight reduction holes, like in aircraft, Drop in grommets and you might not need to bolt any clamps/lines down. Clean look too and as you go you can make "panels" to cover the inner rails to help keep nature from damaging your vitals. Great video by the way.
Thanks for sharing and doing this series. I'm working on my 87 K5 and your videos are really helping!
Great to hear!
I’m planning on doing this to my 91 KV2500 Suburban ..but I’m an total rookie when it comes to what to do-where to start -so here I am
I'm in the process of restomodding my 92 Suburban. Just yanked the 6.0 Vortec from a 2009 3500 van. Thanks for the video. I wanted to see how someone did an LS swap on a lifted squarebody. o7
Only made for 2-1/2yrs with the electronic speed sensor 89-1/2-91, NP241C passenger drop transfer cases are not easy to come by, it took me 15yrs to get hold of one for my truck unless you want to pay a small fortune for one! Advanced adapters has a great kit for adding the electronic speed sensor on the transmission then you could use a less expensive easier to come by transfer case.
How can you tell its a 241c?
@@trashbandit2449 It will have a round tag on it that says NP241C & it will also have the electronic speed sensor in the tail shaft with a passenger side drop.
@@fastjp72 suppose that was fairly obvious but thank you. From the sounds of it I doubt I'll find one anyway haha
don't be so sure. I come across them fairly often. Look at Craigslist for a part out... Ive sold several over the years for around $400-$600.
but, that said, there are other TC's that could be easier, cheaper and more plentiful.
My 89 K5 Jimmy must be an earlier one cause it has the mechanical speedo in the NP241. I live in the rust belt were it's nearly impossible to find any K5's sitting rotted out. Most people sold that stuff off around here in recent years for scrap money.
We have a cabin in big bear. We go often and see you around.
K5LFE... 73's from K5MWA !
Nice K5. Mine's an 88. 14bsf govloc, 10b front w/tru-trac, 700r4 built with Monster Tr. parts, tan/blk raptor paint... etc...
Sounds like a cool setup! I wanted to convert my 10b to 8 lug and go 14 bolt, but found a Dana 60 in Colorado when there at a steal, so down the rabbit hole I went…….
@@carlsandvik2893 Oddly, I retained the 6 lug pattern, using axle shafts for the 14sf out of a 2000ish Express Van (with bigger lugs). That also let me do a brake conversion up front to H3 Hummer 4 piston calipers. No more seized floating calipers and stops like a cat on carpet 🙂. To fit the brakes I went to 17" Black Rhino Arsenal alloy wheels. 18" would have been better, but 17's have worked out ok.
Nice work!! Can’t wait to follow along
Really looking forward to this series. I have an 89 K5 and my brother has a 91 we are looking to do some swaps on. Have either of y’all ever looked into using the Tejas motor mounts? Supposedly let you keep your factory transmission location, low mount AC, and stock oil pan. Seem to be used mainly in the 2wds but have heard of some success stories with 4wd as well.
Hey there. I already have the ORD cross member and motor mounts, so staying with those. Also, I want to keep as much up travel due to having high steer and a ram assist setup, so I went with the Holley 302-2 pan vs an ORD big block engine cross member (or other) to keep the stock pan. I already limited (bump stopped) my up travel due to my ram contacting the cross member at full stuff.
I am definitely itching to get our swaps done!
Looking fwd to this series!
I'm hoping to get my LQ4 blazer on the road soon.
you are going to love it
Any updated videos since this one? Doing the same exact swap and would love to have a step by step guide!!!
I've watched this video a dozen times. Finally ready to pull the trigger but maybe I missed it here but what do you use for a Transmission crossmember? I'll be going 5.3/4l60e/Np241c in a half ton K10 (1983).
I want a manual transmission what are your recommendations? This question is for everyone
curious what did he do with the ac/ heat system? like he went from factory to what? I notice the blue and yellow caps and was curious because I'd like to get the big box out of the engine bay on mine.
I went vintage air. The old system never worked.
@@carlsandvik2893 let us know what you think of that system.
I’ve heard both good and bad reviews and I run a soft too 100%, so not expecting it to be like my daily, but better than nothing , for sure.
stumbled on this, promises to be a great series, don't see anymore vidoes however...is there a plan to complete the series or am i missing the videos?
FYI....In AZ, it is almost impossible to find a NP241 with a passenger side drop. Craigslist, junk yards, Facebook market....no one has a unit. Now, you can get them off eBay but for $3800.00 which I refuse to do. Does anyone reading this thread know a good source or anyone wanting to sell one without me having to mortgage my home? 1978 Chevy Scottsdale is what I have running a 4L60e. Thanks!!!
0:34 not suburban- only escalades came with the lq9 (or silverado SS's), unless it's an LQ4 then yukon denali or 3/4 ton?
Edit- he addressed it. Oops
He incorrectly called an LQ9 a 6.2L though, which is a completely different generation of engine.
Basically a 10:1 on LQ4/LQ9 prevalence
@@Scottross93 yeah he corrected it later. I think
Those sliders look perfect... you gotta vid on how you made them??
Thanks! I don’t have a video, sorry. 2x3x0.25 wall tube with 1.75x0.180 round tube. Just a small angle up on the round tube. 2x2 runners to the frame and then I tied them to my a and b pillars for the cage. They’ve been working great.
I have a sm465 4 speed manual and NP 205 in my 84’ k5 . Would I be able to use this setup with an ls engine?
On the 241c to LS LQ 4/9 will the older non 5 hole 241c tranny fit up to the LS, or is there an adapter needed for like the flex plate or another part for the geometry to work out? I have a 241c in my 1991 Burb I would like to use instead of sourcing another tranny. Appreciate the video, excited for this series as I am underway on the same build.
I am pretty sure there is an adapter. Look into a slip yoke eliminator on that TC before you install though.
I have a 1975 and want to do a LS swap with a 6.0 engine and 4L65 trans with a NP241C case but, how do you deal with having the old transfer case axel on the left hand side to install this the NP241C on the right hand side? no one has mention that, thanks for your answer on advance.
You have to be a great mechanic to work on an LS
You have to be a great mechanics to work on a ford 😂
What did Carl paint the firewall with? Looking for something good for mine.
I used the ceramic Lizard Skin, it went on super nice.
Question. Will the LQ9 from a Hummer H2 work as a swap for a 72 Jimmy? Do you prefer the LQ4 or LQ9? For this vehicle? Is it possible to use the stock transfer case in the 72 with the LQ 4\9 if it comes with the transmission?
Thank you again for your videos they are awesome and inspiring. I have one question what body bushings do you recommend for a k5
I have had good luck with the Energy Suspension bushings.
@@MerricksGarage thank you sir will do
What do you think about changing one of those LS's to a naturally aspirated block? I am thinking about it for a super simple build. Worth it?
It is cheaper to go with the factory fuel injection and computer. You won't gain any power with a carb. But it does make it more simple.
Waste of time, these MPFI systems are so basic.
to be honest, these are super simple already. I mean you only really have like 7 sensors you need to run (MAP, TPS, Crank, Cam, O2, H2O, Oil).... you can hide the coil packs if you want clean and you have a super simple reliable system
@@MerricksGarage thanks sir, I have had a 5.3 for a year now and it has been doing very well in my Brovalanch (avalanche).
What motor mounts, headers, oil pan, trans crossmember do you have to run, thinking about doing a square body k10 with 6.0 and 4l80e thanks
Great video, you have a new sub! How can you make this conversion smog legal in CA.? Any help would be much appreciated.
You need to start with a smog exempt vehicle or swap everything from the donor vehicle
What do you think about the L8T 6.6 Liter gas engine?
With the holley term x dose it change the shift maps for low range like the oem computer?
The LQ9 is a LQ4 with flat top pistons.
What mileage do you get in yours?
I have an NP205, would it be a straight connect up to a 4L80. Or do I need adapters ?
I’m pretty sure no adapter is needed, not sure to be honest. I’m using an ORD doubler, so that serves as an adapter and clocking method.
There’s a guy on TH-cam who has a video on it. You can bolt the 4l80e up to it, theres an adapter for it on Amazon. It’s what I’m gonna do!
Why not use a manual 261 transfer case?I have one in my K20
Isn't that a driver's side drop with the independent front suspension? You would have to switch out your front axle at the minimum, maybe install a slip yoke eliminator driveshaft. Not sure. It would be more work than its worth.
Always wanted the 205 and front dig abilities along with rear lo only. Still have the electronic 261 from my burb, someone is going to want that 32 spline unit.
Hey what fuel sending unit did you use on your k5 LS builds?
I’m trying to run my lines up drivers side and looking at videos and sites spectrum # Fg17b has come up. I ordered one but nothing lines up great…
Hello yall. Would you know if a NP 241c out of a 94 yukon will work ? Thanks yall
1. I want the stock motor. I live in SoCal so I gotta pass smog. I am hoping to find a rebuildable core that might get me 250hp and still keep the stock computer happy.
2. I am looking for stock rear spring hangers (at the rear bumper). I swapped to ORD shackle flip hangers but I am going a different direction now and bringin it back down. If anybody has stock spring hangers, Let me know!
Hey Scott, look me up on Facebook or instagram and message me. I have it posted in Santa Barbara Facebook Marketplace and Offer Up (but chino hills).
Do you really need a different crossmember? Feel like most builds don't even mention a cross member jjst buy mounts and it drops in.
Lq9's were 06 and up
😂😂😂
Hi James. Where did Carol get those rear quarter panel armor?
Woods’ Off-road in San Marcos.
Thank you 👍
1st 😄 Nice content James.
Legend!
Can u guide us to a hands on video
It’s probably better getting the Holley EFI kit. It has instructions which makes it easier.
the Terminator X Max does make it pretty easy
The old tbi 350 pulled so good at low rpm. Not fast, but a good truck engine. Im curious as to why you replace the crossmember, I've done a ton of these swaps, and never had a issue with this.
Me thinks that ORD might be a sponsor so he plugs their stuff when he can. Or he just does everything to the max. I take his suggestions as the best way to do things. I substitute when I can't afford the high end parts.
i like this
cool
LQ9 is also a 6.0 not a 6.2
What is 'l.s."?
LS is the Gen IV engine family from GM. The umbrella term for any GM V8 with a few exceptions
@@MerricksGarage savvy. Thank you
Sixth 👊🏻💪🏻
Did this guy say that you will alright in a chain driven transfer case ????😂😂😂😂😂 for what ? Going to the grocery store? Or pulling your boat from the boat ramp ? Must not be going too far off road .
I ran a chain drive 241 for years. Must not know what you are talking about.
Tooooo much talking
Blah blah let's get wrenching. Leave the acting to the professionals. 😂😅
All the sheep asked for it. Its just another overrated LS swap. Nothing exciting..
Yet here you are. Watching and commenting. Oh wait, but you are different.