I got a v6 pico chip that looks like this v6 instinct chip (cable goes over the ram, under the cpu shield and bends over to install). Should work the same right? Flash chip, solder components, install chip, cut shield, reassemble, install sd card with cfw? Thanks for the videos and work you do they have been very helpful so far.
My Switch Lite shows the Instinct NX screen but it is unable to go through the OFW. Whenever I try I always get a blue screen. I also get a black screen while I try to boot the console with the sdcard inside.
I have no power to chip and system after installing the ribbon cables. Any idea as to what could be happening? It boots up normally if the chip is disconnected.
it depends on your thoughts. my thoughts say the chip is pressing the cpu shield when the metal shield is not cut. when you say nothing happens doesn't mean it is safe. you can think logically
Hi, I accidentally updated my switch to the latest firmware and now when I boot my switch the screen stays black, my emunand is working fine with the latest ams and hekate but sysnand is not!
@sthetix I completed the mod and it boot fine into OFW and Hekate. However, when I tried to back up EMMC the unit would froze and locked up. Any pointer on what to do next? thank you.
@@sthetixofficial I got it fixed. I found one loose connection on the flex cable connector and maybe the cut off part on the heat shield is touching the usb port that might cause a short. Everything were corrected and now working like it should.
Mr Sthetix, I installed a modchip following this tutorial and everything worked until the last step.. I extract the HATS pack into microSD card but when I put it back in the switch, it either fails to boot (modchip glows purple then green then shuts off with nothing displaying) or displays a message saying failed to boot init. Do you know anything about this? I tried formatting my microSD, I did this via Macbook, idk if that's an issue, any help would be appreciated.
Hello sthetix I would like to install this mod kit on my lite, however I have absolutely no experience in soldering as a whole, let alone micro-soldering. Before I start doing anything to consoles I would first like to practice and learn soldering and micro-soldering, is there anything in particular that you recommend for this type of thing? Many thanks.
You'll need to practice soldering for small repairs before installing the modchip. For example, repair the Xbox or the PS3 analog stick. You will be confident later.
You’re an artist! Amazing skills.
Thank you! Cheers!
T12-BC1 tip is what I used as well. It’s really good!!!
That is a mad microsoldering skills. you made it look easy! That is insane! Susbsribed!
amazing video! gonna download this incase it gets taken down again! keep up the good work!
Much appreciated!
My man, the gift that keeps on giving!
Where can i find that ribbon cable for the lite?
Cant seem to find it anywhere
Love the vids cheers
you can find it on ali
Hi! Thanks for the content. I was on your store an wondering if you would be able to do the Dialga and Palkia edition?
It is out of stock BUT you can do the same mod for the Dialga Palkia
what type of soldering tip did you use at 5:15 to solder the cpu capacitors
it is t12 bc1 tip
Bro, did you watch the video on mute? they even stated which tip they are using
I got a v6 pico chip that looks like this v6 instinct chip (cable goes over the ram, under the cpu shield and bends over to install). Should work the same right? Flash chip, solder components, install chip, cut shield, reassemble, install sd card with cfw?
Thanks for the videos and work you do they have been very helpful so far.
yes they are the same
🔝
My Switch Lite shows the Instinct NX screen but it is unable to go through the OFW. Whenever I try I always get a blue screen. I also get a black screen while I try to boot the console with the sdcard inside.
Try to repair the nand withthe level1 guide.
Looks like the ninjas were at it again! Great video otherwise, here giving it its view from the previous one!
Thanks for the visit
The mod kit and fpc kits are nowhere to be found 😢. Any recommendations or if they will be in stock again?
I have no power to chip and system after installing the ribbon cables. Any idea as to what could be happening? It boots up normally if the chip is disconnected.
maybe the ribbon cables is damaged? please check the soldering points for short.
What about the sp caps anchor gnd points 😮
we dont need it, as it is included on the sp caps.
there it's some reason to cut the main metal shield? I never cut it, and never put kapton on chip, my console is working fine for a year
it depends on your thoughts.
my thoughts say the chip is pressing the cpu shield when the metal shield is not cut.
when you say nothing happens doesn't mean it is safe.
you can think logically
@@sthetixofficial ok I check that, thanks!
Untuk nyolder dat0 hanya di versi oled ya gan?
iya
@@sthetixofficial satu lagi gan, kenapa harus memilih methode kamikaze daripada menggunakan dat0 adapter?
Hi, I accidentally updated my switch to the latest firmware and now when I boot my switch the screen stays black, my emunand is working fine with the latest ams and hekate but sysnand is not!
try using my latest hats pack, 1.6.2, run sysmmc, it should work.
@sthetix I completed the mod and it boot fine into OFW and Hekate. However, when I tried to back up EMMC the unit would froze and locked up. Any pointer on what to do next? thank you.
try to replace the sdcard
@@sthetixofficial I got it fixed. I found one loose connection on the flex cable connector and maybe the cut off part on the heat shield is touching the usb port that might cause a short. Everything were corrected and now working like it should.
Mr Sthetix, I installed a modchip following this tutorial and everything worked until the last step.. I extract the HATS pack into microSD card but when I put it back in the switch, it either fails to boot (modchip glows purple then green then shuts off with nothing displaying) or displays a message saying failed to boot init.
Do you know anything about this? I tried formatting my microSD, I did this via Macbook, idk if that's an issue, any help would be appreciated.
try using other sd card brands.
how come the soldering iron doesnt damage the cable? sorry for the stupid question, i am a noob when it comes to soldering
because it is heat proof.
Hello sthetix
I would like to install this mod kit on my lite, however I have absolutely no experience in soldering as a whole, let alone micro-soldering. Before I start doing anything to consoles I would first like to practice and learn soldering and micro-soldering, is there anything in particular that you recommend for this type of thing?
Many thanks.
You'll need to practice soldering for small repairs before installing the modchip. For example, repair the Xbox or the PS3 analog stick. You will be confident later.
@@sthetixofficialI'll be sure to give those a try, thanks for the suggestion!
is the process for the v6s on switch lite similar to this?
yes it is the same.
well done :)
Can follow the same instructions for consoles v1 patched abd v2 ?
the concept is still the same.
Where can I get the kit ? I tried looking for it but all I can find is the v1,v2 and v3
you can dm me on X or twitter
What would you more recommend, the new v6 Instinct NX or Picofly?
v6
Is it the same process for picofly?
Hello after soldering I got blinking pattern 🔵…🟡🟡…🟡🟡…🟡🟡 what could be the issue pls
My switch never boots to hekate anymore after updating to 17! It only blinks Purple for a bit Then WHITE! Then straight to OFW Heelp! 😢😢😢
there is something wrong with the installation.
oh. okay. that happened to me before .. i just waited then its fixed again. Then this happend again. 😭
Hi, i need Contact to you, i have some problem with my nintendo switch lite after updating the instint v6 mod
Yes?
🎉
Why hide the battery info? And the switch logo?
ninjas
Your discord invite link doesn’t work anymore on your about page
you can contact me directly.
Can you make a tutorial of modding new nintendo 3ds systems?
it is there in my channel
Thank you sir
I can't find any V6 any source/links?
it is on ali.
Did you miss a logo in the original upload?
the logo is exposed in the original upload.
Beli chip nya di mana ya bang?
Di aliexpress atau di tempat laen.
Yoooooooo 🕺🕺🕺🕺🕺
An easier way doesn’t exist?
it is the easiest way
It does but you need a first gen switch to do it
Too ez