E-Moto Chain Tension How To // E-Ride Pro, Surron, Talaria
ฝัง
- เผยแพร่เมื่อ 8 ก.พ. 2025
- Thanks for watching!
Please consider subscribing!
CHECK OUT OUR WEBSITE FOR ANY UPGRADES YOU ARE LOOKING FOR ⬇️⬇️
tbelectricmoto...
Best 19in Upgraded Tires: tbelectricmoto...
Talaria Pedal Kit, Talaria Sting R MX4 vs E-Ride Pro SS, Best Sur Ron Controller, Talaria X3 Street Legal, Talaria X3 Controller Upgrade, Best Electric Dirt Bike, Talaria Direct Mount Stem, Surron Ultra Bee Upgrades, Talaria Sting R Unboxing, Talaria Sting R Battery Upgrade, Most Powerful Electric Bike, How to Change Talaria Brake Pads, Talaria, Surron, EBike, Utah, Trending, Talariasting, Dirtbike, Emoto, ForYou, TalariaXXX, Talariax3, Talariamx4, Talariamx3, Surronx, ForYouPage, TalariaStingR, Talariar, StingR, FYP, Shorts, ForYou, Utah, Moab, ElectricMotorcycle, SurronX, Luna Cycle, Review, Ebike Review, Sting R, Super Moto, Faster Than Surron, Best Electric Bike, Under $3000, XXX Unboxing, XXX Review, Sting R Review, Talaria Review, Surron Review.
10-15mm is chain slack is all that’s needed. Just tightening the axle nut will give you inconsistent chain tension. Put a towel in the chain and roll wheel forward. Will set axle blocks against tension bolts. Tighten axle nut and then roll wheel back and remove towel. Chain tension will always be the same
The eride pro is a beast in the snow.
thank you very much, greetings from germany ;)
Excellent video thank you very much.
Thank you for providing valuable content. Gonna check the tension on my Talarias using your tutorial
Thanks!
Please make a video going over proper front and rear suspension settings. I have an E Ride Pro SS 2.0. I am new to the whole scene and feel like my suspension is probably not correct and I cant find any info on how to set it properly. I also want to know in case I have a bad rear shock like you guys had on your 2.0.
Will do
Some suggestions : More details on the chain play (50mm up and down when measured in the middle?) and how tight to tighten the centre bolt when done.. 🙏
Did this process today and had to repeat like 5 times, what a pita, must be an easier way or better system to adjust it property isn't it?
Thank you sir
Because of the flex in the swingarm I have to run mine a bit loose. When hitting big jumps and scrubbing it will bent the sprocket as you land.
Good to know
@@TBElectric yeah, I bent 3 sprockets before I switched to the titanium axle and started running my chain with a bit of play
On a Talaria?
just got my sting friday, haven’t cut the wire, chain seemed tight when I got it, rode 8-10 miles, noticed it had worn in and would move about an inch and a half up between the sprocket and gearbox.
got it tightened up, only thing is I was unsure of wether or not it’s too tight, I saw people saying 10-15mm of play in the middle, seems like it’s close to that but i’m also guessing it may wear in a little more?
any videos on belt tension?
We will make one
@@TBElectric I'd appreciate that a lot. I'm sure others will as well. There seems to be very little Indepth and updated videos. I know you guys will be thorough with it :)
I would like to see the brake pads replaced
Video coming soon
The brake side for me doesn’t move no matter how much I turn it, i assume it’s broken?
Ya that’s not good
@@TBElectric what do u think I should do?
Same here neither side will move at all
@@vladimirp8470 I emailed luna n created a ticket, if they get back to me I’ll relay the information to u if you’d like.
@@vladimirp8470 I’m not sure on how to fix it rn, but I’ve emailed Luna n created a ticket asking for advice. I’m gonna go on Reddit later today and see if anyone has had a similar problem.