Very nice, I'm glad I was able to give you ideas for your build! Thanks for the shout out. I love the slanted rear tubes.. they're going to really mesh with the shock mounts.
😩I'm falling so far behind! 😅...Really nice work, it's looking great. Between you and the Binder Builder I'm getting lot's of ideas for my cage, excited for more progress!
Lookin' great Miah!!! The Binder Builder fella is a pretty smart dude!! Lol!!! Keep it going!! (Where did you get your tubing notcher and the profile tool? ( Black plastic with the rods).....
The tube notcher is from Vevor and the profile tool is from Centurial. I try not to buy top brand tools for things that will have limited use. Thanks Tim for your support sir!
All right I appreciate the absolute precision and hard work you're doing but are you purposely making it so you can roll it that is extreme Overkill unless you know for a fact you're going to roll it that's a lot are you putting like 1,000 horsepower motor in it it's just so much work and Overkill extreme Overkill but it's awesome as hell to watch and I'll continue watching every time you post because it's a badass build I'm just curious
I will be pushing the car hard. Not planning to roll the car whatsoever but as most people in the off-road industry know, roll overs happen often. I put a lot of value on my life. This is actually a standard roll cage for cars less than 2500 lbs. Over that is 1-3/4” tube. With my 240HP engine, speeds will commonly 80-100mph. Thanks for watching!
I love that you dont have long videos but are showing a TON of info/content
I’m glad you like them that way. I will be going more this direction in the future! They are easier to make too!
Badass video!!! Love how you showed everything but it wasn’t 30 min long🤙🏼
It’s hard to find a balance. A lot of people want to just see it built, others want to know how to use the measuring tape 🤣 thanks man
@ delicate dance!
Very nice, I'm glad I was able to give you ideas for your build! Thanks for the shout out.
I love the slanted rear tubes.. they're going to really mesh with the shock mounts.
Thanks Dom. Yeah, I decided it wasn’t worth the buy for a roller bender for a few tubes. This method worked fine.
Love these bugs. Wish I had the know how to confidently tackle a project like this.
You could always start small and build confidence! Thanks for watching!
Tight work dude!!
Thanks Gary!
Great work
Thank you!
😩I'm falling so far behind! 😅...Really nice work, it's looking great. Between you and the Binder Builder I'm getting lot's of ideas for my cage, excited for more progress!
It’s really picking up speed now. I can’t wait to get the engine hung!
Looking good 👍
Do you prefer notching by hand or the hole saw notche?
I only use the hole saw notcher if it’s a single straight notch. Otherwise I found it’s faster (for me) to just use a grinder. Thanks Matt
Lookin' great Miah!!! The Binder Builder fella is a pretty smart dude!! Lol!!! Keep it going!! (Where did you get your tubing notcher and the profile tool? ( Black plastic with the rods).....
The tube notcher is from Vevor and the profile tool is from Centurial. I try not to buy top brand tools for things that will have limited use. Thanks Tim for your support sir!
@MiahsBug Watch that sir stuff mister!! 🤣🤣
@@timswitzer792 😂 all the cool kids say “sir” now. Apparently being respectful is retro now
@MiahsBug Lol!!
All right I appreciate the absolute precision and hard work you're doing but are you purposely making it so you can roll it that is extreme Overkill unless you know for a fact you're going to roll it that's a lot are you putting like 1,000 horsepower motor in it it's just so much work and Overkill extreme Overkill but it's awesome as hell to watch and I'll continue watching every time you post because it's a badass build I'm just curious
I will be pushing the car hard. Not planning to roll the car whatsoever but as most people in the off-road industry know, roll overs happen often. I put a lot of value on my life. This is actually a standard roll cage for cars less than 2500 lbs. Over that is 1-3/4” tube. With my 240HP engine, speeds will commonly 80-100mph. Thanks for watching!