how to use power supply tester

[@noloferratus]

That was very helpful thanks! I found out my power supply was fine and instead a cat peed inside and shorted out my motherboard.

[@tunkunrunk]

my story is different , I accidentally dropped my fork inside my computer , it shorted my motherboard

[@mofo78536]

Sounds like your cat is defective, get it replaced under warranty

[@johnnnnnnnnnn17]

is there a reason you didnt connect the pcie connectors?

[@1776_Reasons]

My P.G. shows 100 but it's blinking/beeping and everything else is in normal range. Does that still mean my PSU is bad?

[@Bou89]

What about the PCI-e cable? can should it be connected with the 8-pin CPU?

[@seollenda]

Everything is fine except the PG.. The value its reading is 120ms and its flashing. What does this mean?

[@dabbzgaming]

Did you ever find out? My PC won't boot and my PSU is giving 130ms on pg and flashing like yours

[@seollenda]

@@dabbzgaming I just bought the same one off Amazon then returned it with the faulty unit lol

[@1partgeek]

@@dabbzgaming Same here, all stats are good except for PG showing 130ms and flashing and beeping! :(

[@bobbrock4221]

Nice video. Be better without the music, it's distracting.

[@user-px4lf4mx7c]

Very helpful

[@kanyeeastlolz]

what if the PG value is in range and the tester constantly beeps showing the PG value turning off and on? What's the issue then?

[@DarkFusion]

My -12V is showing 11.7 V is that normal ?

[@patelshome806]

Same question

[@windfire5380]

For Thermaltake 1200W ATX3 I plug in 24 pin and 8 pin and I get constant beeping / flashing of PG value at 120ms. What does that mean? I wonder if the 1200 uses the second 8pin (it has 2) and my tester only has 4/6/8 not two 8s???

[@brodanate]

You can test the 8s one at a time

[@sham1234567891]

Great stuff!
I checked a psu and all voltages are shown as on your screen. But only 2 leds are on and the 3.3volt les is off. Could you please give me an opinion? Thanks and regards.

[@KaleemNoonari]

3.3v only lights up on sata cable not molex or any other as he have said that in video.

[@johnluiegonzaga1501]

useful video.. thank you for sharing your knowledge

[@ahsansazib]

*How I check PSU watt?*

[@westmantooth6846]

killowattmeter

[@YeahClickClack]

The power tester doesn’t seem to work if there is no 20-24 pin connector. My power supply only has a 4 and a 6 pin connector.

[@xbgpisonetpartsandcomputer9179]

Hi. This power supply tester is for 20 pin and 24 pin.

[@YeahClickClack]

@@xbgpisonetpartsandcomputer9179
Darn! Wish I knew what kind of power supply I had before purchasing the tester. I’m sure I’ll be using this on other ones,haha.

[@uzkniso88]

I've checked a psu and everything pass, but when PSU connected to any PC it does not work. PSU spins for a second and turns off. Seems like this tester is not 100%
accurate

[@user-eu2me9xr9x]

Motherboard is dead

[@PierreRees]

Or maybe graphics card. I had a gtx970 that was tripping my PSU. Soon as I took the card out. It worked fine

[@sankarkripakaran3239]

Purchase link... Power supply

[@joemarapuan2783]

Saan po nakakabili ng PSU TESTER?
Pwede po makahingi ng link.
Thanks!

[@allan-liam9331]

Vengo del estado de Plaza Celular

[@jakkamadhu4335]

Wow

[@georgepanganiban6421]

LL = Low Level Voltage.

[@Medieva1]

Hi, When I only connect my 24 pin connector to the tester, I get the LL. But once I also plug in the cpu or vga cable it goes away. what does that mean??

[@CougarCat21]

What about H-H? What does it mean? My 5VSB has H-H.