Great video. Give us more videos same. When make videos more closer please. Because we can't see which component you checked with multimeter. Thanks for sharing your experience to others. Valuable videos.that you posting.
Sir kindly share the dts IC number and HDMI selection ic number, I have one same model, without the ICS please share the details very helpful. Thank you sir
Shorted semiconductor normally will have less than 10 ohm, at most times, total dead short. Since your short is around 40 ohm, it may be caused by leaking MLCC cap.
Fyi, It's not always 40ohms short. Controller ic short causes multiple ic short so on circuit we can't measure the ohms correctly. But if we remove the controller ic we can detect the fault easily. But without a controller ic no use to fixing other things .so I dropped it
I have all size stencil. It's not about reballing bro. That ic is dead short so no use in reballing the IC. And if I removed it that I have to spend solder balls and time. Waste for everything. And customers do not pay for reballing the IC
Kenwood A65. When volume increases upto half above it's automatic muted. After when we push the mute button it's not unmute. On this situation we restart the amplifier then it's running. But still this problem when we max the volume. Please give me solution for this.
@@fixavreceiver I encountered an issue with my old F&D T60X speaker. The f&d t60x own amplifier seems to be dead, so I purchased a Kenwood A65 amplifier to power the speaker directly. However, when I increase the volume to halfway or above, the sound gets muted. I suspect this could be due to the speaker being low-powered for this amplifier, making it incompatible. What are your thoughts or recommendations on this?
Hi Brother You have to charge a minimum of 500 for attempting fees otherwise you have a struggle also If not people send it to the very worst piece also
@@fixavreceiver முடியாத பட்சத்தில் customer ta கேட்டு வாங்கி போட்டால் set முடிந்தது போலவும் உங்களுக்கும் ஒரு happy customer திருப்தி அடைந்து யிருப்பாரல்லவா
அப்படி இல்லை sir, new board is very costly and all other service centres doing the board replacement. நானும் அதையே செய்தால் அப்புறம் எண்ணுக்கு என்று தனித்துவம் இருக்காது
Use full and knowledge gain videos real great thank u.Not fixing video want.
ramba use fulla eruku sir ramba than Qu sir
முதல் முறையாக உங்களாலேயே சரி செய்ய முடியாத வீடியோ
You try your level best sir nice work we will always support you sir same time it will happen anyway you try your best always fan of your work
So nice of you
Great video. Give us more videos same. When make videos more closer please. Because we can't see which component you checked with multimeter. Thanks for sharing your experience to others. Valuable videos.that you posting.
A sincere attempt but revival challenges remain.
Hard luck bro.never loose heart❤
Sir, please upload all videos daily basis.... we r eagering to watch ur videos...
But Good Attempt ji...Many time Iam also facing this type of Problem, Most of the Customer not understand this Situation......
We accept your situation of hard work. Tuff to accept the electronic is fails after a big handwork
I want to watch every video sir because I want to be like you
Good work and expected your rectification but unluck. Super bro. Ivalo amount spend panni vangitu waste ah pochi la
Yes bro
Your very honest brother
Good work
God bless you sir
Use full video bro ,
Great effort sir👌👌
Good effort bro ❤
Thanks ✌️
Sir kindly share the dts IC number and HDMI selection ic number,
I have one same model, without the ICS please share the details very helpful.
Thank you sir
please ping me on whatsapp
சூப்பர்
Good 👍
Super ❤
இது மாதிரி சர்வீஸ்ல நான் நிறைய லாசா இருக்கேன்
Tirippi fit pannumbodh athe maari tag ellam pottu kudupingla ??
Yes
Shorted semiconductor normally will have less than 10 ohm, at most times, total dead short.
Since your short is around 40 ohm, it may be caused by leaking MLCC cap.
Fyi, It's not always 40ohms short. Controller ic short causes multiple ic short so on circuit we can't measure the ohms correctly. But if we remove the controller ic we can detect the fault easily. But without a controller ic no use to fixing other things .so I dropped it
@@fixavreceiver We cannot buy the controller IC?
No bro, but we can get it from the old unit of the same model for some other fault condition.
Reballing stencil mobile repair shop la irrukum bro
I have all size stencil. It's not about reballing bro. That ic is dead short so no use in reballing the IC. And if I removed it that I have to spend solder balls and time. Waste for everything. And customers do not pay for reballing the IC
I have model denon avr-1912, and from its center channel and subwoofer there is this disturbing noises that comes at intervals.
How to solve this?
Need to check it in dac and DSP signal area and then opamp and volume ic area. If all ok then check it at AMP section area
@@fixavreceiver thank u sir for reply
Good
யமஹா hdmi பிராப்ளம்.கண்டாக்ட் நோம்பர் sir
9943124215 -please whatsapp me sir.
Kenwood A65.
When volume increases upto half above it's automatic muted. After when we push the mute button it's not unmute. On this situation we restart the amplifier then it's running. But still this problem when we max the volume. Please give me solution for this.
It may be a volume ic problem. And for this fault we need to check it at signal level
@@fixavreceiver I encountered an issue with my old F&D T60X speaker. The f&d t60x own amplifier seems to be dead, so I purchased a Kenwood A65 amplifier to power the speaker directly. However, when I increase the volume to halfway or above, the sound gets muted. I suspect this could be due to the speaker being low-powered for this amplifier, making it incompatible. What are your thoughts or recommendations on this?
Upload not fixed video also❤
Iam also waiting for my amp same to same model 😅
❤❤❤🎉
Marantz sr 5600 problem pow5 ?
Commen fault indication in this model. Fault anywhere in the AMP. We need to check it all one by one
Onkyo 626 hdmi board irukka
no sales only service
Anna f9234 ic iruuka
available
Which place
Vellore
Address please
Contact and address details are in every video description
reball processor...if not okay change processor
Changing the processor does not work ***pre-programmed IC**.
Oh okay brother
😊
Hi Brother You have to charge a minimum of 500 for attempting fees otherwise you have a struggle also
If not people send it to the very worst piece also
Yes bro
Bro not fixed videos vanum bro pls
ok
புது board வாங்கி போடலாம்ல bro
It's not my job bro, my job is fixing a faulty board..
I never do that kind of replacement work.
@@fixavreceiver முடியாத பட்சத்தில் customer ta கேட்டு வாங்கி போட்டால் set முடிந்தது போலவும் உங்களுக்கும் ஒரு happy customer திருப்தி அடைந்து யிருப்பாரல்லவா
அப்படி இல்லை sir, new board is very costly and all other service centres doing the board replacement. நானும் அதையே செய்தால் அப்புறம் எண்ணுக்கு என்று தனித்துவம் இருக்காது
நான் என் பயனியர் 5.1 a/v receiver ப்ராப்ளமா இருக்கு , உங்களை எப்படி காண்டாக்ட் பண்றது போன் நம்பர் ப்ளீஸ் !!! ...
9943124215- please whatsapp me sir ☺️
Not fixing video want
ஏன் சார் HDMI போர்ட் வாங்கி பொருத்தி தந்திருக்கலாமே
Board changing is not my job sir. I work as much as I can to fix the faulty board.
@@fixavreceiver New HDMI boards are not suitable for this receiver.
No sir , suitable but very costly. 18k 6-month warranty. In Bangalore service Onkyo centre
Very costly.sir.i think your suggestion is very good.appriciate your Job.
எவ்வளவு கஷ்ட போட்டோ அது வொர்க் ஆகவில்லை
தொல்லை பிடித்த வேலை😢
Sir phone number please
9943124215- please whatsapp chat sir.
Super