At first the robot voice was a bit irritating, but after a few seconds I quickly realized this is the most outstanding instructional video I've seen on TH-cam. Great Job!
Thank you for the video. It worked, though when I was checking the Cartridge for leaks without inserting the shaft and gear, the toner powder started to drip off the hole where the shaft and gear are placed. So, I had to insert the shaft/gear and then everything went smoothly. For those who also use starting cartridge and hl-l2395dw. In order to remove the replace toner message, open the Cover (where the cartridge is placed), press X, then wrench/screwdriver, all settings, general setups, scroll down to "replace toner", select "continue" instead of "stop". Hope it helps.
Why are there so few sellers of toner powder to refill these cartridges? Is it the 3rd party market for cartridges are cheap enough not to go through the refill process vs the raw cost of toner?
You left out a step in the re-asssembly in this video. After the roller is reinserted and BEFORE the c-ring is popped in, there is an important piece that needs to be put in, that the c-ring holds in.
Holy smokes, this is an incredibly involved process. Buying new toner powder looking possible until I saw this process. I'd feel better off selling off the empty cartridge and getting a new replacement one that is full. I know that means $$$ but I don't want to risk the refileld cartridge exploding and contaminating my printer.
I think BROTHER hired him to make this video so people don't bother doing this and just go buy the damn toner LOLOL which i will be doing. i dont have an air compressor nor the time to do this. i thought it was gonna be a lot easier. I found new toner for $11 on amazon ill test that out first. It's good for people who have the time to do this or may even enjoy doing diy stuff like this.
Where it says "remember the starter cartridge has no reset gear." can you still use the starter cartridge as seen at 05:04 or do you have to get a replacement for that end of the cartridge that has a reset gear?
@@viandant5 Thank you for that info. One more question please, when air blowing the cartridge to get any remaining old toner off, do you have to blow the air into the fill hole to get any excess toner out of there or will tapping the cartridge into a plastic bag be enough before refilling the fill hole with new toner?
@@simonbpuk2949 It would ne better to blow the cartridge. Tapping the cartridge should work but there is the risk of grey background on the page if too much toner remains into the cartridge
Thanks for a nice video! Some questions about the chip: (1) Does the starter cartridge also have a chip? (2) I don't understand what you mean by "remove the old cartridge chip" and "replace the chip in the new cartridge" since you're just refilling the old cartridge.
can not use the menu button, can not get past the replaced tone cart message, nothing else is allowed, so how do you get to the ignore cart when menu is not selectable with error message??
Great video! But I was wondering, instead if compressed air can't we just use a vacuum cleaner? Compressed air is not easily available and more importantly wouldn't it make a mess anywhere it was used?
I'm using this video and your other video, 'colour toner in black laser printer' as a reference for something I want to try. I want to empty a cartridge and fill it with white coloured toner from Aliexpress. However, they don't list my printer/cartridge model as 'compatible'. Do you think If i use a brand new drum+cartridge (clean of black toner) it will still be fine?
Let's say I don't have the starter cartridge anymore, will it work if I don't replace the chip with the chip that comes with the starter cartridge ? Is there another way to make it work ?
@@viandant5 Thanks! It's good to know. Also, is there a way to know what quantity of toner (in g) I have to put in it ? I have a TN-760 brother cartridge. Does it makes any difference if I put too much ?
@@Nicolasgtix 90 grams of toner. It's useless to put too much toner, you'll have the error message after a numbber of copies, not important how much toner is left into the cartridge
@@viandant5 So for the tn2420 brother toner i need its specific refiller. I've search it on Amazon buy i didn't find it: do you know where i can find it? before buying the printer (mfc-l2710dw) I want to be established :).
At first the robot voice was a bit irritating, but after a few seconds I quickly realized this is the most outstanding instructional video I've seen on TH-cam. Great Job!
my voice is far worst
Thank you for the video. It worked, though when I was checking the Cartridge for leaks without inserting the shaft and gear, the toner powder started to drip off the hole where the shaft and gear are placed. So, I had to insert the shaft/gear and then everything went smoothly.
For those who also use starting cartridge and hl-l2395dw. In order to remove the replace toner message, open the Cover (where the cartridge is placed), press X, then wrench/screwdriver, all settings, general setups, scroll down to "replace toner", select "continue" instead of "stop". Hope it helps.
nice to see bruher make it simple to refill..
Thanks for detailed video! You are the best!👍👍👍
Why are there so few sellers of toner powder to refill these cartridges? Is it the 3rd party market for cartridges are cheap enough not to go through the refill process vs the raw cost of toner?
You can use almost all black toner powders for Brother machines
You left out a step in the re-asssembly in this video. After the roller is reinserted and BEFORE the c-ring is popped in, there is an important piece that needs to be put in, that the c-ring holds in.
Which one is that? I'm having trouble with my printer that I just refilled the toner in
GRACIAS, MUY BUEN VIDEO ,MUY CLARO ,Y FACIL,PARA GENTE QUE SEA TRANQUILA Y LE GUSTE PONER ATENCION Y AHORRAR DINERO ,GOOD JOB
Awesome video! thanks so much.
Holy smokes, this is an incredibly involved process. Buying new toner powder looking possible until I saw this process. I'd feel better off selling off the empty cartridge and getting a new replacement one that is full. I know that means $$$ but I don't want to risk the refileld cartridge exploding and contaminating my printer.
What??? This isn't involved or hard at all lol. Just give it a shot, honest it's easy and VERY difficult to mess up lol.
Hes just makung it seem harder than it is. Just open the lid. Fill it back up and put it bacj in
I think BROTHER hired him to make this video so people don't bother doing this and just go buy the damn toner LOLOL which i will be doing. i dont have an air compressor nor the time to do this. i thought it was gonna be a lot easier. I found new toner for $11 on amazon ill test that out first. It's good for people who have the time to do this or may even enjoy doing diy stuff like this.
Can't you just add toner to the cartridge without going through the complete tear-down and cleaning?
The reset gear? yes, you can
Where it says "remember the starter cartridge has no reset gear." can you still use the starter cartridge as seen at 05:04 or do you have to get a replacement for that end of the cartridge that has a reset gear?
you can add a reset gear, or reset the printer using the control panel
@@viandant5 Thank you for that info. One more question please, when air blowing the cartridge to get any remaining old toner off, do you have to blow the air into the fill hole to get any excess toner out of there or will tapping the cartridge into a plastic bag be enough before refilling the fill hole with new toner?
@@simonbpuk2949 It would ne better to blow the cartridge. Tapping the cartridge should work but there is the risk of grey background on the page if too much toner remains into the cartridge
Thanks for a nice video! Some questions about the chip:
(1) Does the starter cartridge also have a chip?
(2) I don't understand what you mean by "remove the old cartridge chip" and
"replace the chip in the new cartridge" since you're just refilling the old cartridge.
Start cartridge has ho chip. Remove the old chip and reistall it only if you are installing a new cartridge without chip. If not, let the old chip
@@viandant5 thanks!
@@viandant5 ok so it will work without the chip too kk
@@radekw708 It needs a chip, new or used
@@viandant5 I thought starter cartridge has no chip?
Can I use this method in tn 2465
can not use the menu button, can not get past the replaced tone cart message, nothing else is allowed, so how do you get to the ignore cart when menu is not selectable with error message??
If you set the gear in the right position the error message should disappears when you insert the cartridge
Great video! But I was wondering, instead if compressed air can't we just use a vacuum cleaner?
Compressed air is not easily available and more importantly wouldn't it make a mess anywhere it was used?
Sure, a toner vacuum cleaner is perfect. A normal vacuum could not become a problem, often their filters cannot hold the tiny toner particles
I'm using this video and your other video, 'colour toner in black laser printer' as a reference for something I want to try. I want to empty a cartridge and fill it with white coloured toner from Aliexpress. However, they don't list my printer/cartridge model as 'compatible'. Do you think If i use a brand new drum+cartridge (clean of black toner) it will still be fine?
Which white toner? For this printer?
Hi. Excellent and clear instructions.
I have done the same but now I m getting toner ended msg and can't get rid of it.
At the end of the video there are reset instructions, if you have no reset gear
excellent video, thank you
Let's say I don't have the starter cartridge anymore, will it work if I don't replace the chip with the chip that comes with the starter cartridge ? Is there another way to make it work ?
The chip from another cartridge will work the same
@@viandant5 Thanks! It's good to know. Also, is there a way to know what quantity of toner (in g) I have to put in it ? I have a TN-760 brother cartridge. Does it makes any difference if I put too much ?
@@Nicolasgtix 90 grams of toner. It's useless to put too much toner, you'll have the error message after a numbber of copies, not important how much toner is left into the cartridge
@@viandant5 Good ! Thanks a lot for your help. :)
Hello, thanks a lot very good video. Do you know wher i can buy the toner for a brotner tn241 ? Thanks a lot, stephan
I think you could use Amazon, they sell good compatible toners or search with Google avoiding ebay
I guess TN-2411 is similar? Do you know how much toner i must fill in 2411?
Yes, it's similar. It takes 90 grams of toner
How come you have to replace the chip on the cartridge and with what? Why can't you reset the cartridge with existing chip?
If not present in the new cartridge you have to use the chip of the old cartridge
@@viandant5 I want to just use the starter cartridge and refill every time, so dont need chip right?
@@radekw708 Yes, you need a chip
@@viandant5 can you explain though, how does the starter cartridge work without a chip?
@@radekw708 The printer has a software that tell it to accept the installed cartridge
The refill cap broke and then got lost inside the unit. After I filled it with toner I had to throw everything out.
Pour the toner in a bottle and remove the cap with pliers. Glue it if necessary
Excellent video and finely explained.
Tocayo hahaha
there is no other information about printers toners and cartridges in this this TH-cam channel .
Where does one get the bottle of toner?
Try uninet imaging, or search with google
Is it possible to refill the tn730 starter kit cartridge for the 2370dw brother
yes, but there is no reset gear
Hi! Does any refilling toner works well for any tipe of cardige or evrey one needs a specific one?
no, there is not an universal toner
@@viandant5 So for the tn2420 brother toner i need its specific refiller.
I've search it on Amazon buy i didn't find it: do you know where i can find it? before buying the printer (mfc-l2710dw) I want to be established :).
@@usk8130 You can use almost every black toner specific fot Brother pritners
Ese modelo usa revelador?
no
Thanks for your video. I think it gives me a lot of tricks solutions. #compatibletoner
i cannot open the screw
Try a different screwdriver.
can you just refill without pulling front off & cleaning? how many grams will the TN-2430 cartridge take?
The risk you have copies with an heavy grey background. This cartridge takes 80-90 grams of toner
thx
Thanks
It's tedious than what I thought.. I'll just buy a new one
The gear it's not same with TN 3608. Please give tutorial the real TN 3608 .
this video is related to TN730 series toner cartridge. I wil make that video when I'll have a toner TN36900 in office
@@viandant5 thank you ☺️
Ridiculous how companies don't make this more reusable what a waste, sick capitalism
this is so damn stupid, I can get 2 toners that yield 6000 pages at supplies outlet, who the heck would do this
You can, someone else not