Intercom installation onto dirtbike helmet. MX helmet speakers.
ฝัง
- เผยแพร่เมื่อ 29 ส.ค. 2024
- Here is a run down on how to install a speaker assy from headset into your none audio setup helmet, whether it be a MX helmet or a basic street helmet if there is no channel for cutout for speakers to be inserted then this becomes very uncomfortable to wear and also down right annoying because the speakers tend to fall out and displace easily.
Here with this tutorial you will see that its not rocket science and with a little patience it can be done perfectly. what a great way to make your headset fit better !
Special thanks to:
www.Shadusa.com
www.fxrracing.com/
www.brightsidecustoms.com/
www.connecthearing.ca/
www.filmora.wondershare.com/
www.cooperators.ca/
www.sena.com/
Dont forget to check out my gear and good section!
Sena 30k headset: amzn.to/39OHBQO
Sena 20S-Evo headset: amzn.to/3qKoIW5
Sena S10 Headset: amzn.to/3ivkOgA
Sena SMH10-11 headset: amzn.to/38ZPYtx
Quadlock handlebar mount: amzn.to/31CkwN2
Quadlock mirror mount: amzn.to/3gPb679
Rotopax fuel caddy: amzn.to/31H1xRw
Fuel bottle 30oz: amzn.to/2DC2cMa
Slim fitting handguards: amzn.to/3gOwh9j
Phat wide handguards: amzn.to/2CmA4fi
Ténéré 700 Screen protector: amzn.to/33OHS4F
Ténéré 700side protector: amzn.to/33SUDv4
Ténéré 700lowering kit: amzn.to/31HjWh1
Ténéré 700 Dominator exhaust: amzn.to/2XRjtYw
Ténéré 700 skid plate: amzn.to/2Fflwzc
Sena 30k Single: amzn.to/3ky0qfr
Gopro hero 7 black: amzn.to/31FPAeJ
Gopro audio pack: amzn.to/2DAR4PH
Padded bike shorts: amzn.to/3kxiuX8
Hydration pack: amzn.to/3iqeNAC
Disclaimer:
This channel is strictly entertainment purpose only.
Please note that It’s a Dyer thing Channel is not affiliated with Yamaha Motor companies-service/sales/support/marketing in any way.
All that is published on It’s a Dyer thing channel is presented to you from a personal experience for means of entertainment only.
None of the products shown on Its Dyer thing channel is endorsed by the manufactures or suppliers.
Please be safe, act properly and ride responsibly.
Should you have any questions or need to seek professional advice, please consult the manufacture or representative of the product(s) in question.
Dealerships and manufactures will always know what is best and are protected by law.
This channel is strictly entertainment purpose only.
I'd think you could do it without a dremel. At least with other foam like in equipment cases and such you can put cross hatch cuts creating a bunch of little squares that are easily pulled out.
I did similar by hand on my Bell MX9 MIPs. I used a tea spoon and lots of force. Wasn't the best job. Ive got a Dremel but I don't have the Flexi shaft so not sure it'll fit in my helmet easily.
Looks like a nice clean job. 👍
Hey. What ever works my man. Thanks for the feedback and chat. Have yourself an amazing season
i’m trying to put a intercom in a bell mx9, did you find the ear speakers stick out too far? i don’t wanna do any pushing in of the foam
Without having this helmet I’d say I’m 99% you don’t have to use a dremel.. just remove the three nuts around the speaker space
They would be pressing too much against the ears. So very little tolerance between the side. But that could also be me having big ears hahahah
Cheers and thank for the feedback which. Also makes a good point and option too !
Rob