Ford Focus MANUAL SWAP! Pt. 5 | Wiring Harness Work!

แชร์
ฝัง
  • เผยแพร่เมื่อ 23 ธ.ค. 2024

ความคิดเห็น • 18

  • @vidaiautomation
    @vidaiautomation 14 วันที่ผ่านมา +2

    Dude.... that's quite the step out of the kitchen there! Awesome series!

    • @BigBensCarsAndCycles
      @BigBensCarsAndCycles  14 วันที่ผ่านมา

      @vidaiautomation thanks! Been a while, you been doing ok?

  • @nicksimadis2086
    @nicksimadis2086 14 วันที่ผ่านมา

    I can't wait for the programming side of this! Great series, Ben!

    • @BigBensCarsAndCycles
      @BigBensCarsAndCycles  14 วันที่ผ่านมา

      @@nicksimadis2086 thanks! We have a programming guide in the discord!

    • @nicksimadis2086
      @nicksimadis2086 14 วันที่ผ่านมา

      @BigBensCarsAndCycles now does all this keep everything stock with functioning cruise control and getting the engine to not think it's in park/neutral? Last guide I looked as was PS on TH-cam, and he was having those difficulties. But he was like one of the first to do this and publish his results. Again, thank you for making this!

    • @wcvp
      @wcvp 14 วันที่ผ่านมา

      @@nicksimadis2086 Yup, everything works as if it came manual from the factory (including cruise control and the IPC telling you when it thinks you should up/down shift). You don't even need a new PCM, it's just a matter of finding the correct firmware image to flash to it.

  • @rewiredhusky9907
    @rewiredhusky9907 14 วันที่ผ่านมา

    Def coming back to this because the DSP6 sucks lol thank you!

  • @MG-fk1qb
    @MG-fk1qb 14 วันที่ผ่านมา +2

    thanks for this video its very helpful , i just finished my car and its 100% like stock

  • @tkmad7470
    @tkmad7470 14 วันที่ผ่านมา

    Good stuff! Have you thought about putting together a swap kit?

  • @GREGHOLUB
    @GREGHOLUB 14 วันที่ผ่านมา

    I guess I’m not understanding you need to cut your connector off of the wire harness then re solder every wire you cut ?

    • @BigBensCarsAndCycles
      @BigBensCarsAndCycles  14 วันที่ผ่านมา +1

      @GREGHOLUB after removing the tcm connector, all the unused left over wires got heat shrink to seal them. That's it. No solder or splicing

    • @GREGHOLUB
      @GREGHOLUB 14 วันที่ผ่านมา

      @@BigBensCarsAndCyclesI gotcha I totally forgot that the tcm will be removed because it’s now a manual and you will not need the connector because the tcm is gone totally makes sense now thanks!!

  • @charlescarignan186
    @charlescarignan186 14 วันที่ผ่านมา

    What can block my ignition to go on??my car crank but wont start what can it be?

  • @wcvp
    @wcvp 14 วันที่ผ่านมา

    Oh interesting, I didn't realize ford uses different connectors sometimes, they look basically the same lol

    • @BigBensCarsAndCycles
      @BigBensCarsAndCycles  14 วันที่ผ่านมา +1

      It was almost impossible to see with the naked eye. Only when I zoomed in with my camera. The pins are a snugger fit on the ones that came on my car