I have just replaced a stolen Samebike lo26 500W with the same model and am noticing some real differences in performance. The main problem is that the throttle gives me LESS power than the PAS. On my old bike I could happily ride along on the flat on PAS1 then hit the throttle if I came to a small hill and get more than enough of a boost to get up the hill without having to increase the PAS level. On my new bike I actually lose speed if I use the throttle. Thinking this had to be something that I could sort out by changing one or more of the settings, I was shocked to find that the only settings I can change are P01, P02, P08 AND P16. The others just refuse to change. Is there anything that I can do to change this or is it a faulty unit? Also, the new bike has 12 positions on the left gear shifter. Surely there should only be 3 on a 21 gear bike? My chain comes off a lot more than I have ever experienced with any bike!
its all about the controller. I just had to replace mine as well as the screen ,its just not the same anymore. I'm just happy it works again after an E10 ERROR.
I recently got a bike with the same controls and display but I cannot change the settings like you show it in the video, I can only change the display brightness and the speed limit, is there a reason for that? Is there a way to be able to change the settings?
all i have is throttle no pedal assist on my xdt valk bike can some how help? im pretty sure its something in the menu so if some one knows how to completely reset it back to stock that would be so helpful
I will try to clarify it a little bit. In this bike there is no advantage to use 9 levels PAS since there is actually only 5 different levels. 0&1=off, 1&2 same as 1, 3&4 same as 2, 5&6 same as 3, 7&8 same as 4, 9 same as 5. And the difference between these 5 levels are the assisting max speed limit. In PAS 1 the limit is ~16kmh, 2 is ~22kmh, 3 ~25kmh, 4 ~ 29kmh, 5 ~32kmh. This varies a little bit and depends on the battery voltage. When the battery voltage is lower, also the speed limit is lower.
The best i have seen so far. Thankyou. Will now set PO7 to 1 to get speedo reading which I have never had. How can you get a total factory reset to start from scratch?
From the manual: P00: it is Reset all parameter Function: Change the value as 10, then short press the “M” key, the screen will Display all segment, then all parameter will reset to the original value
i recently bought an electric bike with the LCD S830 installed. I have been trying to change some settings in the configuration menu according to your video, but they seem to be locked and cannot be changed (for example P04, P05, P09 etc.). Do you know how i can unlock these settings and make them customisable? That would be of great help!
I've heard some manufacturers lock their settings- I do not know if it can be unlocked without replacing the controller unit. I'm sure you can find the information from electric bike forums, try keywork Lectric XP
Hello David, you can use the S830 as a charger for your phone. I'm not sure if it is possible the change the firmware via USB. The S830 has several functions which aren't mentioned in this video.
Can you explain to me why I cannot change some parameters on my bike? I want to change the P10 parameter but it's locked on 2. I have a Bezior M26 that I think is the same components as the Sam Ebike.
Thanks for this my s830 LCD was messed up, but p15 has no use on mine. P7 should it always be at 1 because on the manual is says 47 for direct drive and 86 for geared hub. So just to clarify its definitely 1?. By the way my magnet sensor has 7 should I put it to 8.
P7 depends on the controller and the motor. You should use the value instructed on your manual. P13 should be approximately the same value as the amount of magnets, in your case 7 is the closest.
I have a cmacewheel y20 which has a 750w motor. On some off road rides I find it too powerful... can I reduce the power say to the equivalent of 400-500 W ? The display is similar , not the same as the s 830 ... which I have on a ‘samebike’
you should be able to lower the strength of motor kick in. If it has same parameters then set the P12 and P14 to lower values. More info in this video.
I'm just not getitng this at all mine is all over the place, I don't have a clue what I'm supposed to do, or if it's even faulty. Whty is the battery display flashing and showing empty? it's literally fully charged. Why doesn't it show my speed? Seriously this is impossible without clear instruction.
@@andrewhutchinson3071 Seems to be that some S830 models have also clock, though I didn't find any info how to to set the clock time. My best guess is to press up and down at the same time or you could also try pressing UP+M or DOWN+M
@@mysteriouschinapackets1728 I was kinda wrong, is a timer for current session not a clock, so nothing to set as it goes back to 0 when the trip does... Evertime I saw it was at the end of a ride and it didnt click it was a timer not a clock.
@@andrewhutchinson3071 Yes, it has a trip meter (time and distance of the current run) which I find very useful. It automatically resets it every time the LCD turns off. I didn't cover the basic functions in this video. Please comment if you need one.
When you reach your desire speed with the throttle press the down arrow for a few seconds...this activates cruise control...if you do it at walking pace it activates walk mode 6kmh
Very detailed, clear and instructive. Thanks a lot !
Best video on the subject around. Very clear explanations and images. Thanks an awfull lot!
Glad you enjoyed it!
@@mysteriouschinapackets1728Spidometr clear yes ?
Amazing video! Finally someone informative and smart.
Finally someone translates the S830 manual!!! Thanks.
Спасибо большое брат! Это лучший урок! Ты мне очень помог разобраться с этим дисплеем!
Great job mate. You solved my sons problem with his bike.
Solid Piece of Equipment
It's clear like this. My l026 needs to use right brake and M button 5 sec. to save certain settings. Like max speed. Great bike!
Good to know. i’ll test that.
@@mysteriouschinapackets1728 Hi can you please tell me if you can cap the voltage to 250w on this display? To make it legal
This is the best explanation. Thank you.
I have just replaced a stolen Samebike lo26 500W with the same model and am noticing some real differences in performance. The main problem is that the throttle gives me LESS power than the PAS. On my old bike I could happily ride along on the flat on PAS1 then hit the throttle if I came to a small hill and get more than enough of a boost to get up the hill without having to increase the PAS level. On my new bike I actually lose speed if I use the throttle. Thinking this had to be something that I could sort out by changing one or more of the settings, I was shocked to find that the only settings I can change are P01, P02, P08 AND P16. The others just refuse to change. Is there anything that I can do to change this or is it a faulty unit?
Also, the new bike has 12 positions on the left gear shifter. Surely there should only be 3 on a 21 gear bike? My chain comes off a lot more than I have ever experienced with any bike!
its all about the controller. I just had to replace mine as well as the screen ,its just not the same anymore. I'm just happy it works again after an E10 ERROR.
thsnks for the video gr8 help just wat the dr ordered cheers
BEST VIDEO EVER!!
I recently got a bike with the same controls and display but I cannot change the settings like you show it in the video, I can only change the display brightness and the speed limit, is there a reason for that? Is there a way to be able to change the settings?
Same Problem
same problem
I have a Gotrax EBE 2
The throttle is not working
E 08 code on the display
I don't know what to do
Can you able to help me out
I only have po 1,2,8 and 6. Is there something I can do to find the other settings
For P05 - what do you mean by - First number sets the start level (0 or 1)? So, what does 0 do? And what does 1 do?
How come when I press my up and down button the PO 12345... doesn't come up. I just get 5 0's at bottom the rest of the screen is blank?
Really helped me
Set P18 to 150 and P5 to 2 increases PAS levels from 5 to 9. This will increase your speed to over 35 mph
I only have up to p16
Very clear. Thank you.
Do you measure and include the tyre in the wheel size settings or just the rim size please?
Default is rim size which probably includes some kind of outer diameter. You can use this paramter to calibrate the speed when comparing to GPS speed.
Whats max speed?
all i have is throttle no pedal assist on my xdt valk bike can some how help? im pretty sure its something in the menu so if some one knows how to completely reset it back to stock that would be so helpful
If I caught it correctly, there was no difference in power from PAS level 5 to 9! Is that correct? Ever get it resolved? Thank you
I will try to clarify it a little bit. In this bike there is no advantage to use 9 levels PAS since there is actually only 5 different levels. 0&1=off, 1&2 same as 1, 3&4 same as 2, 5&6 same as 3, 7&8 same as 4, 9 same as 5.
And the difference between these 5 levels are the assisting max speed limit. In PAS 1 the limit is ~16kmh, 2 is ~22kmh, 3 ~25kmh, 4 ~ 29kmh, 5 ~32kmh. This varies a little bit and depends on the battery voltage. When the battery voltage is lower, also the speed limit is lower.
Got it, thanks for taking the time to reply.
The best i have seen so far. Thankyou. Will now set PO7 to 1 to get speedo reading which I have never had. How can you get a total factory reset to start from scratch?
Thank you! Unfortunately I have not found how to factory reset the LCD.
From the manual: P00: it is Reset all parameter Function:
Change the value as 10, then short press the “M” key, the screen will
Display all segment, then all parameter will reset to the original value
Hi! I am only able to adjust P01,P02 and P08, the rest doesnt move… do you know why?
same
Any way to Increase the canadian version past p0 2? It doesn't go higher than that due to regulations. Something In the controller I can do?
What is the default value for P14, P15 and P16? thank you
This depends on the bike. The default values for this bike are shown in the video.
Большое спасибо 🙏😇
Great video mate!
Can you tell me whats the settings for P13 for this bike?
You mean amount of magnets at 5:23? You can count them. It's 5.
What to do when the screen is not starting after you press M???
Hi I know this is 2 years ago am having a promblem my battery percent always says 100 percent
HI , Just got my s830 display switched off on the spot though bikes battery is charged 50%, anyone know why and how to fix this problem? thanks
i recently bought an electric bike with the LCD S830 installed.
I have been trying to change some settings in the configuration menu according to your video, but they seem to be locked and cannot be changed (for example P04, P05, P09 etc.).
Do you know how i can unlock these settings and make them customisable? That would be of great help!
I've heard some manufacturers lock their settings- I do not know if it can be unlocked without replacing the controller unit. I'm sure you can find the information from electric bike forums, try keywork Lectric XP
Same and i got a Samebike lo26
Same problem
my voltage always reads double. no matter what i set the voltage (p3) at, 48v battery reads 96v, when fully charged. can i fix this?
Cant change my setings, why?
Some LCD’s have locked parameters. You might need to change the controller to unlock it.
Meine gesagt km werden nicht gespeichert, können sie mir da helfen ? Habe Parameter umgestellt weiß nicht wie die original waren .
What is the top speed of the bike when you leave the speed limit to 100? does it actually go 100km/h?
The top speed depends on the battery voltage, controller output and the motor power. In this bike the maximum speed is about 32kmh (16mph).
When i set p07 to 1 it goes to 13km/h but it can go to 35 km/h
Same question
Thanks for the video what is the USB at the bottom of the unit for? programming or maybe charge like your phone?
Hello David, you can use the S830 as a charger for your phone. I'm not sure if it is possible the change the firmware via USB.
The S830 has several functions which aren't mentioned in this video.
Sir whats that circle adjuster beside the handle bar for?
Does anybody know if it is possible to limit the throttle to 6 kmh in non zero start and PAS up to 25 kmh?
How do you turn on the front light I don’t know if it is broken or what
Press and hold up button
I dont ubderstand how to count the magnets. I have euy f6.
Is closed captions enough or should it also have a voice over?
Озвучьте
Can you explain to me why I cannot change some parameters on my bike? I want to change the P10 parameter but it's locked on 2. I have a Bezior M26 that I think is the same components as the Sam Ebike.
Some bikes have the parameters locked. There might be some way to unlock them though.
@@mysteriouschinapackets1728 thx, I'll try to find some way.
Thanks for this my s830 LCD was messed up, but p15 has no use on mine. P7 should it always be at 1 because on the manual is says 47 for direct drive and 86 for geared hub. So just to clarify its definitely 1?. By the way my magnet sensor has 7 should I put it to 8.
P7 depends on the controller and the motor. You should use the value instructed on your manual. P13 should be approximately the same value as the amount of magnets, in your case 7 is the closest.
@@mysteriouschinapackets1728 thanks, I ended up phoning the shop my bike is from they told me 1.
@@BertAndSmokey Good to know! There's no harm to try other values. Usually only one value will work and 1 is the most common working value.
is it possible to set the walking mode for 15 - 13 km on the display s 830
Nie
I have S700 and every time my Trip and Odo are reset when turn off. Can you help me? Thank you in advance. BTW, good movie. THX
I have a cmacewheel y20 which has a 750w motor.
On some off road rides I find it too powerful... can I reduce the power say to the equivalent of 400-500 W ?
The display is similar , not the same as the s 830 ... which I have on a ‘samebike’
you should be able to lower the strength of motor kick in. If it has same parameters then set the P12 and P14 to lower values. More info in this video.
My Speed indicator is not changing. Whats wrong with my set up?
Did you try to set P07 to 1?
I'm just not getitng this at all
mine is all over the place, I don't have a clue what I'm supposed to do, or if it's even faulty.
Whty is the battery display flashing and showing empty? it's literally fully charged. Why doesn't it show my speed? Seriously this is impossible without clear instruction.
What do p11?
Can the speed and distance be changed to mph and miles instead of km?
Yes, it's the P02 setting in the video.
Can someone tell me what the USB port is for?
It’s a 5v charging port, for phones etc.
Can I get 25mph on this bike like I can with my kristall e5 bike 🚴💨💨💨💨💨💨🤔
how to get max speed,it goes like about 20km/h now
If you need to unlock the speed limit, change the P08 setting to 100.
What do i press on the bike to activate throttle ?
Did you figure it out?
Why no sound
Max Pas get to 9 But Italien was 5 what can i do?
The most convenient setting is 5
Very good instruction but wish you were speaking. How do we reset the S830 to factory settings? Thanks again.
I don't think you can factory reset.
Почему без звука
I need the basic instruction to turn on the light . So where have they hidden this freaking button for lights ??
Up button for few seconds.
Thanks, that worked :)
I meant dp168
Whats is the Beat voltage?
I am sorry, I don't understand
like speed wise?
Anyone know how to set the clock ?
This model does not have a clock feature.
@@mysteriouschinapackets1728 mine does. Cycle though pressing M and it the last one. Buggered if so can figure out how to set the time.
@@andrewhutchinson3071 Seems to be that some S830 models have also clock, though I didn't find any info how to to set the clock time. My best guess is to press up and down at the same time or you could also try pressing UP+M or DOWN+M
@@mysteriouschinapackets1728 I was kinda wrong, is a timer for current session not a clock, so nothing to set as it goes back to 0 when the trip does... Evertime I saw it was at the end of a ride and it didnt click it was a timer not a clock.
@@andrewhutchinson3071 Yes, it has a trip meter (time and distance of the current run) which I find very useful. It automatically resets it every time the LCD turns off.
I didn't cover the basic functions in this video. Please comment if you need one.
What is Pas 11 please ?
P11 PAS sensitivity. 3:46 Higher value means you have to peddle longer before the motor activates.
3 months old, mileage 250 km, but where to turn, where to complain, bangood does not cover the warranty and I do not have a dealer address
Hi I have a problem with Samebike LO26 please contact the dealer in Poland so I can complain thank you
hmm no volume
good
I'm glad that you liked it
Mine just stays at 19mph regardless
Is it possible to change it to a color screen?
What bike are you using?
Hi, SAMEBIKE MY-SM26. You can find more info from my other videos
I have a dp+68
You're handlebar is a bit off though...
If you mean it's not perfectly centered, the camera perspective might make it look a bit off centered.
You were right. It was actually few millimeters off-centered.
How to make your bike run at a steady continuous spped
If you mean cruise control without pedaling or pressing throttle it's not possible without hardware modifications
When you reach your desire speed with the throttle press the down arrow for a few seconds...this activates cruise control...if you do it at walking pace it activates walk mode 6kmh
not sturdy at all. made very cheap. avoid this product.
Useless.
I want to change P12, but it does not let me change the values. Is there an unlock sequence to do this. Multiple parameters are locked though
Some models may have parameters locked. You probably have to change the controller to unlock parameters.
good