Lian Li Strimer Plus V2 installation guide (24-pin and 2 x 8 pin GPU RGB power cables)
ฝัง
- เผยแพร่เมื่อ 3 มิ.ย. 2024
- This is an unboxing and installation of @LIANLIHQ 's Strimer Plus V2 kit which is RGB extension kits that come with either 24-pin motherboard cables or dual or triple 8-pin PCIe GPU cables. This is quite possibly the easiest way to add RGB lighting to your case and in this video I'm showing you how I did just that in the Lian Li Air Mini.
Please note links listed here include affiliate links which may earn me a commission. Find out more below.*
Amazon US - amzn.to/3vZUfr1
NewEgg - newegg.io/nc131d67f0
CaseKing - tidd.ly/3M8csvE
Amazon UK - amzn.to/3kCa4io
Overclockers - tidd.ly/49ooI4V
Amazon FR - amzn.to/38NfeFv
Amazon IT - amzn.to/3MI34wq
Amazon DE - amzn.to/3MLif8a
Amazon CA - amzn.to/3F9HJtm
Features of the Lian Li Strimer Plus V2:
Brighter, thinner, and more flexible design
High-end silicon wrapped cables
Works with Lian Li L-Connect 3 for new lighting effects and controls
New side light diffuser for extra brightness
Can withstand temps upto 150 degree C
Easy setup
See the official site - lian-li.com/product/strimer-p...
Various lighting modes include:
- Fade Out
- Contest
- Cross Over
- Bullet Stack
- Twinkle
- Parallel
- Wave
- Ripple
- Voice
The Stimer PLUS V2 can be lit up in single channels (each pair of cables counts as one for a total of 6 controllable areas max).
Specs of this build:
Asus ROG Strix Z690 E Gaming WiFi motherboard • Asus ROG Strix Z690 E ...
Intel Core i7-1200K
32GB XPG Lancer RGB DDR5 5200MHz RAM amzn.to/35WDPXC
Corsair RM850X PSU - • Corsair RM850x Power S...
WD_Black SN850 NVMe SSD - • How to install WD_Blac...
Gigabyte RTX 3090 OC Vision
Lian Li Uni Fan AL120 • Lian Li Uni Fan AL120 ...
Lian Li Galahad AIO 240 • Lian Li Galahad AIO 24...
Lian Li O11 Air Mini • Lian Li O11 Air Mini w...
Note:
Existing STRIMER PLUS owners can upgrade to the LConnect 3 features by purchasing the stand-alone STRIMER PLUS V2 controller. Using the new controller unlocks the full software control experience with all the new effects to the STRIMER PLUS.
Specs
Model LIAN LI ADDRESSABLE RGB STRIMER PLUS V2 24PIN
Dimensions 247mm (L) x 56.6mm (D) x 15 mm (H)
Material Silicone/TPE
Cable 200mm
Gauge 18AWG
Number of LEDs 120
Accessories Controller
Model LIAN LI ADDRESSABLE RGB STRIMER PLUS V2 8-PIN
Dimensions 345mm (L) x 43.5mm (D) x 15 mm (H)
Material Silicone/TPE
Cable 300mm
Gauge 18AWG
Number of LEDs 108
Accessories Cable adaptor for motherboard ARGB 3-pin header
Model LIAN LI ADDRESSABLE RGB STRIMER PLUS V2 TRIPLE 8-
PIN
Dimensions 345mm (L) x 56.6mm (D) x 15 mm (H)
Material Silicone/TPE
Cable 300mm
STRIMER PLUS V2 Media Kit
Gauge 18AWG
Number of LEDs 162
Accessories Cable adaptor for motherboard ARGB 3-pin header
🏆Big thanks to my super awesome TH-cam members:
SirSpawnsALot, Meatykeyboard, Beaster Bunny, JayShank007, Rawrr483, DStarastins, McFarty, Riggsy79, Chief Hao, Aaron Yarden, Geralt of Rivia and you? 🏆
🔫Sub to my gaming channel🔫 / @theprovokedprawnpews
Come check me out on Twitch - / provokedprawn
Join my Discord to keep up to date or ask questions / discord
Follow on Reddit / theprovokedprawn
Read this far? You're awesome. Smash those sub and like buttons!
📌 Support the channel:
😍 See the benefits of being a member here - / @theprovokedprawn
Get some merch - teespring.com/stores/the-prov...
Check out my dedicated Amazon Storefront to see my current fave gear - www.amazon.com/shop/theprovok...
📸 Recorded with www.amazon.com/ideas/amzn1.ac...
Shure SM7B and GoXLR - • Shure SM7B and GoXLR M...
PLEASE NOTE
Affiliate links*:
Disclosure: Shopping links within the description of this video generate a commission at no extra cost to you. These are added for your convenience but other retailers are available. As an Amazon Associate I earn from qualifying purchases.
Products:
Products featured may also have been sent for free for review/testing purposes. Often these have to be returned by me, but not always. I endeavour to avoid bias in my videos wherever possible and try to give honest, subjective opinions. - วิทยาศาสตร์และเทคโนโลยี
Watched this video over and over until I finally understood all the connections. Thanks for taking the time to explore each of the connection options. It was a massive help.
This is the best tutorial on Strimer - hands down. Nice work.
Excellent demonstration on how to do this, thank you!
Thanks. Hope you enjoyed enough to sub
My guy broke down wvery difficult part of my buikd from the nzxt fans to these. Thank you my dude 🙏🙏
Glad I could help
Love videos like this one. You helped me with my decision to buy this product. Thanks a lot man, great tutorial!
Glad I could help!
You have a soothing voice id like to listen to an entire audiobook with your voice. Great video btw
Thanks. You can subscribe and watch a playlist instead maybe? 😂🦐
Thank you for this brother 😊 Putting together a new rig and your guide was, as some of my British mates say, BRILLIANT! It’s been a few years since I built a rig.
Glad to help David. Hope you enjoyed enough to subscribe 🦐
Watched your video in micro center only bought the 24pin version got home installed it super easy downloaded the software I’m in love I’m headed out the door to get the 8pin
Did you have to download the software to get the 24 pin to work with lighting on initial install?
@@JourdanFPS did you find out the answer to this bc mine doesnt light up when i turn the system on
@@psynomic @JourdanFPS Same
Thank you for the video! I was looking for somehow change the ugly original cables of my Asus TUF RTX 3080Ti and I found here a good explanation. I have an Asus TUF Gaming GT501 case so I guess I'll have more than enough space to hide the cables behind (this case is huge) so I'm going now to buy those beautiful Lian cables!
I was confused by the 2 connection of this new 3080 instead of 3 which I had on my ex-3090Ti Suprim X (which I returned because of extremely high temperature in my house🤣and bought this 3080 which is anyway a beast and for sure more than I need). Now after watching you everything is clearr, that option of 2 or 3 separate connectors is awesome this Lian guy makes all the things really thinking in consumers needs. Thanks again, greeting s from Spain!
@Unknown Perfect for my setup. Everything works flawless! The 3080Ti itself is also perfect for my current needs. I would have liked to keep the 3090Ti but no. Lot of heat and power consumption for just a little more fsp. For me personally it's not worth it.
I just ordered them you made me to they just look so nice
Can you customize and choose the color of your own? For example if you had the white strimer rgb
@@shadowkage6403ye u can change the color and pattern to whatever you want to
Excellent video. Thank you for making it.
Thanks for watching 👍
You just saved me, i am sure, hours of work trying to figure out how to get my 24 pin to light up properly! Cheers!
Glad to help. Hope you enjoyed enough to sub
Obrigado pelo 100% de explicação, único canal que eu conseguir intender melhor .🇧🇷
Nice and clean! I just ordered these strimers.
Enjoy
@@TheProvokedPrawn I have to plug the USB in order for the lights on the cables to show up?
@@GamerGeekNerdEh Yes for certain.
@@zo07 yes
A very aesthetic build aside, you have an excellent voice! I'm sure you could easily record awesome ASMR videos.
Thank you! 😊
If you buy both the 24 and tripple 8 pins, plus the v2 fans. Can it all be controlled via one controller box or will I need to use both?
Thank you very much for this guide!
Thanks for watching. Hope you enjoyed enough to subscribe.
Plus, I hear these also work with iCue. Neat!
Nice and honest stuff, got my sub for that, thnx
Thanks for the sub!
Great video. Thanks for the amazing explanation. If we connect 24-Pin cable using the argb header, does the Lconnect Controller still needs to be connected with USB header?
i love looking at my rgb. i gotta get this...
Hi i been looking for this answer but cant find it. In this build im almost done. Have a msi suprim x 3090 ti card. It uses a 3 in 1 cable adapter to go to card. I ran that into a liam li 3 plug strimmer for 30 series cards. Im using a be quit dark pro 1200 watt psu. I ran one psi cable that splits into 2 - connectors that go into liam li strimer cable from power supply. I then plugged in another pci cable that put in 3rd plug on stimer cable from power supply. Now theres the other part of that pci cable dangling thats not being used. Is that correct. ?
Seems like you want to do this before you build the pc. Good video thanks
I'm looking to buy a set of Lian Li infinity fans aswell as a 24 pin Lian Li strimer. These two products come with each their own controller. Can I just use one controller, say - the one from the fans to controll all of this? It'd be so much better for me if I could use one hub only.
Fantastic video. Watched it twice yet wanted to confirm, this cable is compatible with most 4090 GPUs right? 24 pin is usually the most common I find around. Thanks!
How many usb headers what you need for the fans and the streamer cables and AIO that has RGB?would you need to buy a a extra usb headers
Thank you for this video!
Thanks for watching. Hope you enjoyed enough to subscribe 🦐
@@TheProvokedPrawn@computergeek3407c an we split the dual 8 pin PCIe connector for 8+6pin GPU PCIe connector ?
My gpu is rx 6700xt 8+6 pin PCIe connector I want to know if it is compatible
Does the led start to light up as soon as you "Power On" or do you need the software before?
I ask because my rgb's aren't working on these not my fans, can't figure out why they are working?
I’m in the middle of building a new pc, I’ve ordered the MB v2, but I’m quite concerned about getting one for the 4090 having heard the power connector has been burning out on some cards, might not risk it.
No 8pin EPS? Good job Lian Li, not that I won't be adding these to my build this month, good chance I will. But them not having an EPS cable is dumb.
i was never so board watching something so exciting
Thanks
1. That makes no sense
2. It’s bored
Need help…connected AL fans 2 sets to ports 1 and 2 on controller. Stimers to their controller then to the Unihub controller. L Connect 3 updated the unihub controller and firmware. No temps showing in L connect 3. Fans not responding to set fan curves. So stressed. Please advise. Thanks
Your Lian Li Build is so Insane, that is my dream PC Build now.. I like to build by myself but I have no experience building PC, if i can im sure i can save tons of dollars. Now, I look on Building PC Company and they don’t have all the Complete Lian Li Build and also it cost so much like a double 😭.
Its okay everybody can build it...I also have zero experience but you can watch youtube how to build your own pc
Hello so I followed this tutorial , I got my 24 pin to work and everything is displaying but when I plug in the 8 pin I get no display ? Idk what the reason might be, thanks in advance
Thanks for the helpful video! Can you use the control box from the Uni fans? To control fans and the 24 pin and 3x8pcie strimer extensions? Or will you need 2 control boxes, a box for strimer and a box for fans?
No. You need both boxes
Does I have to plug the cables into this Controller or is it enough to plug the extentions into the actual cables and Controlling it then with the Software?
I just bought this Lian Li PW16-12PV2 Strimer Plus V2 - Power Extension Cable - Power 4 Pin To Power 4 Pin
For my ASUS 4090 I’m hoping they will work with it
Is it possible to connect the Strimer Plus V2 into the controller box that comes with the Galahad 2 Trinity SL-INF aio? Or would I need the seperate controller?
miss the days of being obsessed with CRSED lol i always hoped to run into you their
It's not what it used to be.
Woah thanks for the founders edition haha. Not sure if it will looks good on a vertical direction for the FE card.
Looks good!
Hello. Have a 3070ti so no official strimer available. I bought the 2x8 pins one and i hope i can just use the LED part, attach it to my current CPU cables and thats it. Do you think it will be ok ?
Not sure if this is 365 days Pc build or you are trying to get my number. Man’s voice is more relaxed than me on my bday.
Stronger than my relationship
Sub for more
I got these now I’m trying to fix the mess it made in the back
can you connect them to the NZXT RGB controller and does a SATA cable come with the NZXT RGB controller?
I have a query…my gtx 1080 has only 1 8 pin pcie connection…can i use this strimer on that, or its a compulsion to use both connectors?
Great video thanks very much, just learning that the 24 pin comes with the controller swayed me so I will get some, as cheaper options only really work if you have 2 ARGB headers on your MOBO, have you tried them with Signal RGB to see what effects can be done on there?
I have not I'm afraid
@@TheProvokedPrawn Apparently they can work in a limited fashion, or you need a DIY controller, back to looking at the Airgoo ones, which I'll only be able to use one of due to only one header on my MOBO, so probably 24 pin, worth you checking out as an alternative option.
very nice voice bro, thank you
Thanks. Hope I helped
is it possible to buy the motherboard rgb adapter separately? i cant find it anywhere
Can you still use the 2 x 2 pin strimer cable if your gpu only has one 8 pin on it ?
Thanks for the video
You're welcome. Hope you enjoyed enough to subscribe 🦐
Do i have buy it with controller or i can use the controller that come with lian lian li infinite fan
Can that PCI e be conectes to the mother boards CPU headers ?
i have both the 8pin and 24pin cord and i have it all pluged in and only 1 cord lights up and i can switch between them but only one cord lights up? any help for why thats happening
I got the lian li can connector box when I bought a triple pack of the fans set up, would these be able to connect into that or does it have to be a whole new box connector? Anyone know?
Am I right in saying that controller is the same as the SL120 V2 fan controller?
If I have the LCD Gallahad, Strimer V2 and Uni Fans, do I need all three controller boxes?
U can also just get the hard drive storage thing out of there, then you will have for more storage.
How you get both in a combo ?
Hi, I'm trying to find an answer regarding the double 8 pin cable , and i have a 4060ti gigabyte oc which only has 1 8 pin connector. Is it still possible to use the one with 2 8 pin and how do you hide the other half ?
Lian li has an 8pin
Hi there, i find your videos very useful and helpful , i have a question ?
i have just followed almost exactly as you done,
( i got them both after seeing this video )
However , i never plugged in is never plugged in the usb header , as i only have 2 and there both in use ! One is from my AL- fans and the second one is ,well , for my usb's and power on etc from my case !!
I noted the instructions saying you could use ether the cable on the GPU strimer , to connect straight to the box , or connect same cable to that strange looking extension connecter, with the 3 pin 5v MB header , again i only have two 5v headers both also being used , so i connected via the controller , leaving off both the USB and that other 4 pin connector with only one wire , as i have no idea where it goes or what its for ...?!?
Long story short, i am getting zero ARGB lights :-(
but i am thinking although i downloaded both L connect 2 and 3 my strimers are not showing up . My PC powers up and graphics RGB is all good ...so did your lights come on once powered up or do i need to activate them first ? Sorry its a bit long winded , only I'm gutted and hoping by explaining what i have and haven't done so far , you can literally shine some light on where i might have gone wrong 😑 many thanks 😊
I got a little work around maybe it will work for you, type into TH-cam ( B-Roll#16 - combining USB2 internal headers ).
You can utilize the usb header you already have on your MB.
You can use something like this for splitting usb and plugging in more than two amzn.to/3xmPFVC
The extra cable from the controller is for pwm fan control (i.e. controlling fan speed via your motherboard) so it's not essential but you at least need usb OR RGB connections for RGB control
@@TheProvokedPrawn Great cheers for getting back , i managed to get then both working , but i am not able to slow down my 3 AL 120 ‘s fans or make them less noisy , so it must be that single wire you mentioned , as it is a 4 pin header but with only one wire would i be able to plug it into one of my many 4 pin 12v header ,thanks again i have just ordered the USB Adapter9pin USB Header Male 1 to 2 Female Extension Splitter Cable 9P Connector…your a star
Hello, thank you very much for the video. Is it possible to sync the extenders with AuraSync? Thanks!
i think it is, maybe update your drivers after doing this though
Love your vids!! Do you think I could use a strimer plus v2 24 pin with a strimer plus v1 triple 8 pin? Will the v2 controller work with the v1, or vice versa? Any clarification would be appreciated.
The controller will work with v1 yes. Though I don't know if you can mix and match
@@TheProvokedPrawn Cheers! I have a 24 pin v1 as it is. It was originally paired with a double 8 pin strimer plus v1. They were a perfect match but I found the colors to be a little faded; the blue was more of a green, the purple very pink. I upgraded graphics cards and bought a newer triple 8 pin v1. It did not match my original 24 pin, the blue is blue and the purple purple. Lol. Bought the v2 hoping it would be a closer match. Haven't received it yet, I'll soon see.
Can you take off one of the 8 pin connectors for the gpu so it’s single 8 pin for it?
Yeah you would just have the extra 8pin sticking off to the side and it wouldn't look as clean or tight, I'm not sure if Lian Li sells the Strimer package with an 8pin connector only, so far I've seen its only 2-3 sets of 8pins
If you have enough slack so the end that connects to the original cable is in the back of the case, you can just put it off to the side. It will look fine. Judging by what I've seen about the software you can control the different rows of lights separately, so I would assume you could turn off the lighting on the one you're not using somehow.
Love your videos i subbed. Do i need a liam li module for each of the cables. One box for gpu and a bix for motherboard connector?. For the gpu im using a liam li 3 plug connector.
No the box does both the GPU and motherboard cables
@@TheProvokedPrawn thank u so much.
Can you connect these strimmer v2 8pin to sl infinity controller or galahad 2 controller ?
Could you check if this would work with ICUE with an Corsair / RGB adaptor? Would be useful to know. I know V1 worked like this.
Not easily I'm afraid
I Would also intressted in the Same question
Very cool, i have the gen b4 this and may sell them and buy these instead. Do you think these are a big improvement over previous gen? They look great 👍!! I ended up selling my originals and brought the v2s, just installed them into my new pc, they are great, very easy to install!
Alas I didn't get to try the previous model so I can't compare.
@@TheProvokedPrawn hey Prawn, my strimer plus does not light up when i turn on my PC but the gpu lights are on and everything is as well. how can i fix this?
@@pavk883 it might not be in the right rib place on your motherboard
@@TheProvokedPrawn If I've only bought the 3x8 pin cables (no controller included), where do I plug the small black cable into to control it? and can i still control it through the L-Connect 3 software without the controller?
@@VeeTalksStuff no you control it through the motherboard if it’s plugged into the rgb port and not the controller
Wish they’d release an all white out edition where the black accents are white
does it work with rog strix motherboard z790 and rog strix 4070 ti?
i have the triple version of the 8 pin
Hey there, I'm back again with another question 😅 I got the lian LI fans and the Strimer cables but it seems like I got not enough USB header on my mainboard? I need 1 for my Corsair AIO and 1 for the fans and 2 for the streamer cables ? Any ideas ?
Something like this amzn.to/3PBm3f2
If i have 1x mobo rgb connector only will that cause issues if i want to have lian li fans as well that requires an additional controller box
Use the usb connection and you can control the RGB via L Connect
3:48 do you have to use the control box or can you just hook straight to the mother board and go with generic RGB lighting?
Apologies, I’m a bit late to the party. But happy new year!
You can use 5v RGB on the motherboard and use your motherboard RGB software, yes. But you won't have as many colour options
Cheers mate, thanks for your help 👍
Is there no cables for the cpu?
my 24pin’s rgb does not sync with the rest. i even used signal rgb, do u know what should i do
would these work with an 8pin and 6pin gpu? I'm new to pc building and want to make sure I'm not wasting my money on the rgb lighting if they don't connect
Watch some other vids I believe they do.
I have the previous versions of the strimer. Can I purchase only the controller box and will the previous strimers work with the box and the software?
Yes
Thankyou 👍
You’re welcome 😊
Hello, is it necessary to connect the argb cable to control the modes, or is it only necessary to use the usb? I have a motherboard that has a 12v connector and it is not compatible
You can do it with just USB if you want
Hey Prawn, I have the AL120 V2 Fans and their control box, can I connect the strimers directly into it or do I have to do some kind of bridge with the strimer box to the fan box?
There's a sync port but from what I remember it's best to just connect both controllers to your motherboard USB.
@@TheProvokedPrawnmy two usb MB headers are already in use . Can I use a usb splitter to solve this ? Or how else do I hook up the usb connection? Thank you .
@@hvacwilly6037 th-cam.com/video/d8vELbWWaCQ/w-d-xo.html
"theres one for a double 8 pin, and a triple 8 pin, you have a switch that switches between the two, so you can't get it wrong.. but make sure you have your switch pointing in the right direction for it to work"
And my hour long investigation is completed -_- thank you for the video lol.
One thing that isn't solved: I tried the other way where I could have my Asus Armory crate software control all of the RGB, and it only worked with the triple 8 pin connected directly into an ARGB header. Despite the lian LI box being connected into an ARGB header, the software could not detect it and as such, it just stayed permanent rainbow....
Wonder why? or am i just stupid again somewhere?
I don’t have enough usb ports on my motherboard but can I use Corsair’s Internal 4-Port USB 2.0 Hub to plug that into my motherboard and plug the usb port for the control box into that hub?
Yup
Your voice is straight out of an Ford commercial
Can you plug these into the hub that comes with the Lian Li Uni fans?
No
@@flo_ssjwhy wouldn’t you be able to?
@@Yungdilas the strimer hub is an rgb hub while the uni hub is a fan controller
@@YungdilDifferent models, and obviously manufacturer companies want to squeeze money out of its consumers' pockets.
Suppose i Have only 8pin GPU, so if i connect only half of the cable with gpu of this everything will okay is it ?
I have done the exact same thing and the rgb dose not turn on the power dose but not the rgb please help
So i have a genuine concern. So i got the 24 pin connector and i plugged it into the main 24 pin cable just like youre supposed to, but i didnt connect the rgb cable because i dont have enough usb2.0 ports. But when i turned on my pc and went into valorant my gpu (i believe) started making a whining noise and my fans started getting really loud. So i turned off the pc and unplugged the strimmer and plugged in the main cable back into the motherboard and it still did the same thing. Currently it should be in the same condition as it was before the strimmer (atleast it should be) but im just genuinely scared and mad because idk what happened. Btw my pc never made a whining noise prior to doing this. It was comepletely silent before.
Sorry to bother you, but could you please tell me if you are only using either USB2.0 cable or RGB cable, or both at the same time? Thank you.
Just usb. Though you can use both if you want
My gpu have 2 power connectors but can i use the 3x8 pin ?
How do these work with a 3090 TI that goes from 3 8-pin connectors to a single 12 pin connector? Would that not of cord be exposed?
They make a 3x8-pin extension also.
I went with the 16-12PV2 to the GPU's included cable that has 4 power connectors. I was wary about using only 3 power connections on this 4090.
While the cables fit in either of the hubs ports, and the 24 pin worked in both slots, i learned that the single end spot is for the 24 in mobo connector and The side with 2 inputs and a toggle switch is for the gpu strimer. I just ran into and issue where 1/5 of my gpu strimer lights were not working,. Lian Li support told me about this. As soon as i switched them to their intended spots, all lights worked.
Another video on installing these cables also did not mention plugging in the small RBG connection cable, and also said you only had to use the Micro USB cable it comes with. It wasn't an "alternative option" and proved wrong- for my set up at least. The lian li controller software did not recognize the hub and its connected strimers until i plugged in the tiny RGB header plug. The RBG connector is the only way i was able to utilize the lian li software and set up my lighting settings. with out it, you just get default rainbow settings. And with out the micro USB I got no lights at all. 4:24
I'm wondering, if you can find a strimer attachment to use with existing cables. I have a white build so they are perfect out of box for me (save the white clip swap outs) but my fiance has a black and red build with nice black and red cable mods. He just wants the light strip and not extra cables. hmm i've been searching with out results.
Does Lian Li Strimer v2 24 pin come with controller?
If I want to have the Lin li effects I must use the usb 2.0 motherboard connection? I bought the triple 8pin for gpu and the 24pin
Yes
hello please help Is it necessary to use both cabel? I mean the MB USB 2.0 header and the 3pin also beacuse I do not have more motherborad free USB.
th-cam.com/video/d8vELbWWaCQ/w-d-xo.html
So if I were to do the 8 pin cables over the top of the gpu, the rgb would be facing the wrong way and I couldn't see the rgb right? Because the clips can't be flipped.
you can flip the leds around.
im doing a lian li build with sl infinits and galahad etc.
Im up at 4 usb cables. I only have 2 slots on my motherboard for it. What can i do to find a solution?
th-cam.com/video/5BIeKjRT3rI/w-d-xo.html
Can I just check that, if I want to use the Lian Li L Connect 3 software instead of the motherboard controls for the lighting, the only cables I need to use is a SATA power cable (for the lighting controller box) and a free USB slot on my motherboard. I just wanted to check before I buy it 🙂
Yes
@@TheProvokedPrawn ok, thanks 😁👍
What do I do if I don't have a spare SATA spot to plug into?
Ha im sold. Micro center here I come and take my money 💰 💴
So, you could in theory just use them as extensions without the RGB?