How to remove and install the front bumper cover on a 2016+ ND Mazda Miata MX5. For all your used Miata parts need please visit us at: www.redlineaut...
The seam between front bumper and hood is not even between both headlights on my ND. It is is smaller at the lh headlight then at the rh headlight. There are no signs of damage or toolmarkings on the hardware of the bumper. How precise is Mazda with its parts?
I have a question I have a Miata soft top 2016 it have the grill that have the fog lights and I hate it can I replace it with the original one and would that break my bumper
Hey Redline, is there any way you could list the part number for the entire bumper assembly? (with the underspoiler as seen here in this video) Thank you!
As far as we're aware Mazda only sells the bumper cover bare, without the grill, lips or lights. That's how we've had to purchase new ones in the past.
The headlights extend down quite a bit further than the visible part of the lens, so at a minimum I would loosen the bumper at the wheel wells and the top, leaving the bottom and DRL's intact. That would let you peel the bumper forward enough to get to the whole headlight assembly.
![[DRIP] ‘Woke Up In Tokyo (RUKA & ASA)’ PREVIEW](http://i.ytimg.com/vi/QN44lcR_VkI/mqdefault.jpg)
Thank you for the video, it'll come in handy to replace my front bumper after it was damaged by someone in a hit and run two days ago
Awesome! It's still a new car on the market, but there needs to be way more vids like this one.
Thanks. We'll be trying to make some more ND how-to videos soon.
Great guide, thank you! Covers lots of small details
Can you show us how to remove and reinstall the front air dam of a ND in Club trim?
Very helpful, Thank you!
Nicely done and easy to follow. Thanks!
Glad it was helpful!
Can you guys video removing front fenders?
ALWAYS tape the edge of your fender and bumper against scratches. It just takes 1 minute.
Awesome video! How much would be a reasonable labor charge be for doing this work to replace a bumper?
The seam between front bumper and hood is not even between both headlights on my ND. It is is smaller at the lh headlight then at the rh headlight. There are no signs of damage or toolmarkings on the hardware of the bumper. How precise is Mazda with its parts?
Excellent video, and very helpful. Thanks!
Very handy thanks for the upload! Subbed
Awesome, thank you!
Do you a video on removing the rear bumper?
unfortunately we don't
I have a question I have a Miata soft top 2016 it have the grill that have the fog lights and I hate it can I replace it with the original one and would that break my bumper
Where can I get this original grill I have the one that have ltd light and I don’t like it
Hi, what about front license plate install, how did you proceed?
awesome
thank you nice
Can anyone here share with me the location of the impact sensor? I was hoping I would spot it in a video like this
Hey Redline, is there any way you could list the part number for the entire bumper assembly? (with the underspoiler as seen here in this video) Thank you!
As far as we're aware Mazda only sells the bumper cover bare, without the grill, lips or lights. That's how we've had to purchase new ones in the past.
@@RedlineAutoParts every headlight cost 850$ :( right?
@@rzu7 Sounds about right for a new one without adaptive headlights
Would you need to remove the bumper in order to remove headlights?
The headlights extend down quite a bit further than the visible part of the lens, so at a minimum I would loosen the bumper at the wheel wells and the top, leaving the bottom and DRL's intact. That would let you peel the bumper forward enough to get to the whole headlight assembly.
Thanks - that's just saved me a shit-load of money :)
"for all your miata parts need please visit us at: ".... at?