Awesome! Great Job! Really inspiring Tutorial. Thank you so much for your efforts making this Video; i will make my own table saw according to yours 😃👍🏻
UK Health and Safety regulations say that a circular saw used for rip cutting should have a riving knife within 8mm of the blade. Most modern saws don't have one as standard because they are generally used on sites for cross cutting, it stops them doing plunge cuts and most importantly it adds a few pennies to their manufacturing costs. However, they are often available as add-ons. I made my table saw using a Bosch and the riving knife was well worth buying. It just feels much safer! I also made a safety switch that I have to poke my finger through a hole to turn ON but can turn OFF with my knee from where I stand.
Nice build. My only concern is the distance between the end of the blade and the riving knife. Makita has circular saws with a riving knife, which moves with the blade. That model is way safer.
Залип, не буду скрывать. Насколько все чётко и продумано. Тот случай, когда руки из плеч и голова чем нужно заполнена. Как я понял, агрегат в квартире установлен? Мусора нет? Аспирация справляется?
А такая здоровенная каретка удобна-ли? Не слишком длинная? Кстати, если есть возможность, достать HPL панели, каретку лучше из него. Он жёстче, чем ДСП. И его не ведёт от сырости. И скользит, как падла.
Каретку хотелось бы ещё длиннее, но ширина столешницы не позволяет. Я бы советовал делать ширину столешницы хотя бы 1200-1300 мм. А не такую как у меня 800
Or, may you get rich and do good, and then you have no issues buying even the one that is better than a sawstop, that would stop before touching it without breaking the stop mechanism 😎 or leave the states 😅
Could you please share the details of the project, such as the thickness of the wood and also the measurements? Sorry if it's in the video and I wasn't paying attention.
Warning :: I HAVE ALREADY TRIED TWO OF THESE. AFTER PUSHING AND CUTTING A PILE OF WOOD, THE PLATE OF THE SAW VIBRATES INTO THE RECESSED AREA IN BACK AND FRONT. THIS WAS A DEGREE EACH WAY WHICH TAKING TO THE LENGTH OF THE TABLE ADDED UP TO 1/8 INCH. SO I BOUGHT A RYOBI AND CUT THE LEGS OFF, RECESSED IT IN A FULL SHEET OF MDF, PROBLEM SOLVED.
@mr.IQhomemadeDIY yeah, cutting one board I can see that. Plus, by the time the sled is done, you have almost no blade left. I cut 4 x 4s from time to time.
It is always good to see when someone makes something great out of basic material by using simple tools. Great work man!
Thank you very much 🙏
This is very nice diy table saw tutorial. it is highly budget saving for a country like me where real table saw are expensive 👍👍
Thank you very much for your comment 🙏👍
Awesome! Great Job! Really inspiring Tutorial. Thank you so much for your efforts making this Video; i will make my own table saw according to yours 😃👍🏻
I am very pleased that my videos inspire people to do something with their own hands. Thank you for your comment.
Быстро, красиво, практично... Супер.
Thank you very much for your comment 👍
Very nice!
UK Health and Safety regulations say that a circular saw used for rip cutting should have a riving knife within 8mm of the blade. Most modern saws don't have one as standard because they are generally used on sites for cross cutting, it stops them doing plunge cuts and most importantly it adds a few pennies to their manufacturing costs. However, they are often available as add-ons. I made my table saw using a Bosch and the riving knife was well worth buying. It just feels much safer! I also made a safety switch that I have to poke my finger through a hole to turn ON but can turn OFF with my knee from where I stand.
You did the right thing. I have this test table saw, soon I will make another one with a shutdown button like yours.
Please tell me where you got the Riving knife as I’m having trouble finding this
Nice build and it’s super accurate well worth a sub
Thank you. Subscribe to the channel, there will be many more interesting videos
You're own made tablesaw very very impressed.
Hello. Yes, I made the saw table myself. Thank you very much for your comment 👍
very good job with tools not too expansive :-) well done keep on bro
Thank you very much for your comment 👍
Nice build.
My only concern is the distance between the end of the blade and the riving knife.
Makita has circular saws with a riving knife, which moves with the blade. That model is way safer.
Hello. Unfortunately, my saw model did not have a riving knife, so I had to make it myself.
Thank you very much for your comment 👍
Fantastics,i got new ideas thank you
Thank you very much for your comment 👍
Fantastic!!
Thank you very much for your comment 👍
fantastic, incredible!11
Thank you very much for your comment 👍
Во замарочился человек. Получилось круче чем заводская
Спасибо большое за комментарий
Fabuloso. Disculpe la pregunta: ¿Sería posible que proporcione las medidas de todos los cortes? (Lima, Perú)
Gracias por el comentario. Lamentablemente no tengo medidas.
@@mr.IQhomemadeDIY Gracias por la atención
бажаю успіхів, друже!
Дякую🙏
Good one!! Do you have a plan for this table ?
Hello. Thanks for the comment. No, unfortunately I don't have a plan.
Put it in the bin would be a start
would love the plans for this
Unfortunately I don't have a plan.
Залип, не буду скрывать. Насколько все чётко и продумано.
Тот случай, когда руки из плеч и голова чем нужно заполнена.
Как я понял, агрегат в квартире установлен? Мусора нет? Аспирация справляется?
Аспирация справляется почти на все 100. Иногда пробивается несколько опилок, но их совсем не много. Спасибо за комментарий 👍
А такая здоровенная каретка удобна-ли? Не слишком длинная? Кстати, если есть возможность, достать HPL панели, каретку лучше из него. Он жёстче, чем ДСП. И его не ведёт от сырости. И скользит, как падла.
Каретку хотелось бы ещё длиннее, но ширина столешницы не позволяет. Я бы советовал делать ширину столешницы хотя бы 1200-1300 мм. А не такую как у меня 800
Perfect
Thank you very much for your comment
Und das alles mit 19mm Spanplatten? Scheint mir sehr wackelig. Wie will er da Platten drauf schneiden?
All dies ist aus 16 mm Spanplatte gefertigt. Die Konstruktion erwies sich als sehr langlebig.
Gergaji meja yang sangat bagus
Thank you for your comment
Going to need this when the United States forces blade stops on all table saws
Thanks for your comment
Or, may you get rich and do good, and then you have no issues buying even the one that is better than a sawstop, that would stop before touching it without breaking the stop mechanism 😎 or leave the states 😅
Exelente, es mejor con medidas.
obrigado pelo comentário
Здравствуйте какие размеры стола?
Здравствуйте. Размеры стола 800*1100 мм
☕️👍
Thank you for your comment
nice
Thank you very much for your comment
Что используется для направляющих к коретки
Профиль для светодиодной ленты. У меня были остатки, поэтому я их использовал.
Could you please share the details of the project, such as the thickness of the wood and also the measurements? Sorry if it's in the video and I wasn't paying attention.
Chipboard thickness 16 mm. table 1100*800
Did you work at ikea? I don't mean it in a bad way
No, I've never worked at Ikea
👍it seemed it was the same way of making the holes centeres on the side🤔
Ne mengenesi kullandınız
Thank you for your comment
Nothing sketchy about this at all.....alot of work to build.
Thank you for your comment
Добрый день. Можете дать ссылку на зажимы которые 13.52 минуте видно
th-cam.com/video/LYuKDKjYEw4/w-d-xo.htmlsi=BHRvTxWbZn1Rqokp
th-cam.com/video/YUB2suF10TY/w-d-xo.htmlsi=awOD1oWptG4n4YwW
how many sheets of melamine did this require?
👋 I made it from leftovers. I used about one sheet of chipboard. thanks for the comment
Warning :: I HAVE ALREADY TRIED TWO OF THESE. AFTER PUSHING AND CUTTING A PILE OF WOOD, THE PLATE OF THE SAW VIBRATES INTO THE RECESSED AREA IN BACK AND FRONT. THIS WAS A DEGREE EACH WAY WHICH TAKING TO THE LENGTH OF THE TABLE ADDED UP TO 1/8 INCH. SO I BOUGHT A RYOBI AND CUT THE LEGS OFF, RECESSED IT IN A FULL SHEET OF MDF, PROBLEM SOLVED.
Hello. I have no vibration. Thanks for the comment.
@mr.IQhomemadeDIY yeah, cutting one board I can see that. Plus, by the time the sled is done, you have almost no blade left. I cut 4 x 4s from time to time.
OSHA would like to talk to you
Thank you for your comment
Was hat die schnitthöhe ,4cm das ist Spielzeug nicht zu gebrauchen,unnötige Arbeit
The cutting height is 5 cm. It is quite enough for cutting chipboard and plywood.
これは用途が限られる。不要。
Thank you very much for your comment
Or, just buy a table saw.
you can do it like that
Why?
If you can’t say something nice don’t say it