Amazing video. I know it takes time to place cameras, check & adjust if required, ensure lighting, narrate and edit the video etc. These sorts of videos are immensely helpful in giving us novices the confidence to take on these very do-able jobs at home. Want you to know the efforts are appreciated. Cheers from NZ!
If you have an old water hose I would cut about an inch to an inch and a half off of it and use those to put on your lug nuts to keep from marring the threads with the pry bar
all of my bolts were seized, had to grind the 36 mm one off, was very difficult to take the axle out of the rotor , and to place it back in was even harder. took me about 3 hours in total lol
Apparently there is a difference between rear axles for a car made in Britain vs Japan. I know mine is made in Japan but is there a difference between the left and right?
What I did was I raised the vehicle so that I can have a enough room to swing a small sledgehammer onto the axle and it worked. The pry bar method was no help
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
Amazing video. I know it takes time to place cameras, check & adjust if required, ensure lighting, narrate and edit the video etc. These sorts of videos are immensely helpful in giving us novices the confidence to take on these very do-able jobs at home. Want you to know the efforts are appreciated. Cheers from NZ!
on point! more 2002-2006 Honda CR-V videos please?
What about the one on the passenger side that doesn't go directly into the transmission but into the intermediate shaft instead?
Man that was so much better (simpler) than I was thinking it would be!
Thank for the video.
You make it all look so easy. Thanks for that. And you covered every problem spot. Thanks for that too.
Excellent job. Thanks for all the time you put into creating this!
Good God!!! You make it look so easy, as taking candy 🍬 from a baby!
Thanks for sharing your knowledge.
God bless you and yours.
Fantastic great job -thanks for video
If you have an old water hose I would cut about an inch to an inch and a half off of it and use those to put on your lug nuts to keep from marring the threads with the pry bar
Thanks! I had this done to my 2005 crv yestetday. How do I make sure all these steps were followed? It's driving ok.
For anyone replacing the axle, its also best to replace the ball joints
Aaaahhhhh alright, time to hit up O’Reillys. Big help appreciate the visual representation
UGH Im having a time lining up the strut bolts...Mine looks much tighter in between then this one...any advice?
If I want to extend the width of my crv, can I replace the axle for a longer one, Instead of using spacers?
Expert advice! I will buy parts from you.
all of my bolts were seized, had to grind the 36 mm one off, was very difficult to take the axle out of the rotor , and to place it back in was even harder. took me about 3 hours in total lol
+adam m Thanks for the feedback! 1aau.to/m/Shop-TRQ
Did you need an alignment after doing this ?
04 crv AWD axles same size for both sides?
Do you think this would translate well to a 2000 CRV?
Where do you refill the axle oil that comes out I can’t find
The plug
What about fluid replacement?
Apparently there is a difference between rear axles for a car made in Britain vs Japan. I know mine is made in Japan but is there a difference between the left and right?
Does the axel have to be flush with the transmission??
Подскажите пожалуйста, у меня на Honda CR-V 2004 года вибрация при старте и на 60 милях, меня крестовины кардана, шаровые, гранаты. не помогает
hey is this Francis ! :)
I replaced my passenger side cv axel. My car shakes about 15 mph and stops at around 25. Anyone know why?
Is this similar to 07?
thanks for sharing!
Drivers side is easy. What about the passenger side?
What I did was I raised the vehicle so that I can have a enough room to swing a small sledgehammer onto the axle and it worked. The pry bar method was no help
Aftermarket axles are going to vibrate
mine a great. got them from napa.
The other side isnt that simple! much harder to remove from the half shaft!
Такая коррозия везде, видимо климат так влияет