Hi, well it work as it suppose to be, flawless atm ^^ . Effective range = maximium range at which sniper has most consistent hit at target, i would say 70 meter, i will do more test next year with rangefinder , bb test, and so on :P
jeje nice bro, another think, in the chrono test, we can see it shot over 190 mps, in FPS is it...over 660fps? In my country the limit is 550FPS. And what about the hop up rubber and precision barrel? Thanks!
It is about 624 fps ^^ in Sweden we have limit at 700 fps xD it Takes AEG rubber which were included in the chamber package which is pretty good, i dont think it is necessary to get a 'better' rubber because with the 2 lever system u can adjust left and right to get the bb fly straight =) , it is a JB-unicorn 6.01 mm barrel = increase velocity and accuracy, ofc u have to balance it with right weight bb =)
cylinder is good, this pin which stopy the spring guide is to loose so when the gun is loaded, this pin is pushed back and it stops cylinder few milimeters earlier (sory for my english i hope you understand what i mean). I've got the same problemy in my well mb03 :(
Hello! Please, do you know if the MAG Cilynder Head that comes with the MAG Cilynder fits in this Sniper ? I see that you are using another Cilynder Head... Thanks!!
Yeah In my case it was, Mag cylinder head comes with cylinder but in this case i were using Airsoftpro hopup chamber and it includes the cylinder head which is made for the chamber.
I got it... I bought one of this cilynder set for my WELL MB03 (because of your video). I want to use this set with the original hopup chamber ( i hope the cilynder head replace perfectly the original ). Thanks for share this information! =D
well mbo3 or jg bar10? which is better since both of them are upgradedable... well slightly cheaper.. now im balancing which is more reliable before or after upgrades? thanks if anyone - noob here 🤘
As retired engineer I was always of the use of silcan grease in metal to metal parts was a big NO NO! scipli isnt the only tuner who advise to use it . why?.
Silicone grease was applied at oring(rubber) which has contact with the surface of the cylinder (Steel). Silicone grease at cylinder(steel), because cylinder is guided by two plastic rings inside the receiver. Metal to metal parts, i often use gear grease.
Short answer: barrel length is one of the factor to accuracy, longer barrel gives the bb more time in barrel to build up velocity, but also need to consider the air-volym from cylinder and acceleration cause by spring. But longer barrel is not necessary a upgrade. More m/s = heavier bbs needs for accuracy. When it comes to sniper rifle, i will go for longer barrel versions because Im planing to upgrade the rifle, i want to reach further out. If i only playing with stock internals then i dont think barrel length will be a big factor.
Hi! I also have bought airsoftpro zero trigger with 160 spring and airsoftpro hop up, but I have only 165 m\s. Do you use stock airsoftpro rubber or aftermarket one?
at 6:22 this video, u see i greased the piston oring, check how it moves with the cylinder (to loose or to tight). that was a problem i had, mine was to loose only shot about 150-160 so i replaced it with a better match oring.
How can I minimize the impact sound of the piston against the head of the barrel? I fucking love this vid bud. It really helped me a lot. And the screw thing u need to do, it also happened to me. Good job
Thx!, I tried before minimize impact sound by putting a customized rubber pad on cylinder head but again this affect the air flow, didnt turn good :P i dont know if there are any good way to do it =)
Scipli I see. For the list of upgrades you listed in the videi description, could you explain like what of them is for? For example, I know that you changed the stock M140 spring to an M170 spring for more power. But it'd be great too if you could explain the other components too (im newb lol)!
Trigger house, steel cylinder/head and piston is to keep durability/reliability when using stronger spring than original else the internals will break with m170 spring. Hopup house, rubber and barrel is to increase accuracy and muzzle velocity.
I think it could be done with just a spring and a piston, airsoft triger and hop up (I think that pink cillinderish thingy) is just for being fancy.. But thats just mine opinion( Me just being amateur) ... Im waiting for a piston spring kit 35euro (Bcose im being cheap ).. Hope my nubmers gonna be close to yours.. I will reply later ;) Good luck...
Hi! I also installed zero trigger v3 but I have problem ... when I pull back the bolt it is very hard ... like metal scrapes on metal ... Do you have the same problem?
Have not experience that problem, but check the screws so they are not scraping the cylinder. Trigger screws and those 2 screw holding the outerbarrel. Adjust with shims if the screws sits to high =)
Original trigger box is metal (aluminium/ zinc alloy), not suitable for heavy upgrades. I personally always go for steel sears to deal with heavy springs.
![[Airsoft sniper rifle Well mb03][VSR-10]How to install AirsoftPro zero trigger](/img/n.gif)
This is the best video to disassemble it good job
Great video ! Helped me a lot ! Thanks again
hi scipli nice vid not sure wether to get them cyma cm 701b , JG Bar-10 or well mb03
any opinion would be nice
DSA Jimbob hi there! You should buy the jg bar 10 then buy a edgi kit! Welcome
Don’t buy a bar mb is a ok bace riffle
Hi, I have been having some trouble figuring out how to use to hopup system levers is there any place or videos that explain it a little better?
Would be good if you can do the same video for well mb4403d and 4418-2
Nice ! I like your videos bro :)
Will be reciving mb03 and upgradr kit for it so i hope this helps🙏😅
Hi my friend. I will buy this upgrade part for my Well. How it works? Effective range? Thanks!
Hi, well it work as it suppose to be, flawless atm ^^ . Effective range = maximium range at which sniper has most consistent hit at target, i would say 70 meter, i will do more test next year with rangefinder , bb test, and so on :P
jeje nice bro, another think, in the chrono test, we can see it shot over 190 mps, in FPS is it...over 660fps? In my country the limit is 550FPS.
And what about the hop up rubber and precision barrel? Thanks!
It is about 624 fps ^^ in Sweden we have limit at 700 fps xD it Takes AEG rubber which were included in the chamber package which is pretty good, i dont think it is necessary to get a 'better' rubber because with the 2 lever system u can adjust left and right to get the bb fly straight =) , it is a JB-unicorn 6.01 mm barrel = increase velocity and accuracy, ofc u have to balance it with right weight bb =)
@@Scipli in Poland we don't have got any strict laws for asg.. I might say that we dont have any laws for asg lol!
Thank you very much for the video!
is it jg and tokyo marui parts compatible?
It is a copy of TM, i think, VSR compatible =)
cylinder is good, this pin which stopy the spring guide is to loose so when the gun is loaded, this pin is pushed back and it stops cylinder few milimeters earlier (sory for my english i hope you understand what i mean). I've got the same problemy in my well mb03 :(
hi, my trigger housing screw on the front is very tight, and i cannot get it free. any suggestions?
I hawe tha same gun but the problem is that i didnt got the longer screw and i would love to know how long it is so i can buy one
Hello! Please, do you know if the MAG Cilynder Head that comes with the MAG Cilynder fits in this Sniper ? I see that you are using another Cilynder Head... Thanks!!
Yeah In my case it was, Mag cylinder head comes with cylinder but in this case i were using Airsoftpro hopup chamber and it includes the cylinder head which is made for the chamber.
I got it... I bought one of this cilynder set for my WELL MB03 (because of your video). I want to use this set with the original hopup chamber ( i hope the cilynder head replace perfectly the original ). Thanks for share this information! =D
well mbo3 or jg bar10? which is better since both of them are upgradedable... well slightly cheaper.. now im balancing which is more reliable before or after upgrades? thanks if anyone - noob here 🤘
Consider the Bar10 to be incredibly similar to the mb03, except with one or two 'upgrades' already done for you.
Bra video mate, och engelskan är ok den med.
Wat did you do toe make IT fit. I tot type Same problemen wit type bolt. Cyma 701
Few meters arrives?
As retired engineer I was always of the use of silcan grease in metal to metal parts was a big NO NO! scipli isnt the only tuner who advise to use it . why?.
Silicone grease was applied at oring(rubber) which has contact with the surface of the cylinder (Steel). Silicone grease at cylinder(steel), because cylinder is guided by two plastic rings inside the receiver. Metal to metal parts, i often use gear grease.
Hi. Could u tell me the different bettwen the short and the long barrel, I see the bm02 which seem quite similar with this?
Short answer: barrel length is one of the factor to accuracy, longer barrel gives the bb more time in barrel to build up velocity, but also need to consider the air-volym from cylinder and acceleration cause by spring. But longer barrel is not necessary a upgrade. More m/s = heavier bbs needs for accuracy.
When it comes to sniper rifle, i will go for longer barrel versions because Im planing to upgrade the rifle, i want to reach further out. If i only playing with stock internals then i dont think barrel length will be a big factor.
Scipli thank you very much, both or them just only different in the barrel long, the number of pistol streng,... are same
optimal lenght for this hop up?
The inner barrel is 509mm =)
My (GSG MB03) stock barrel is 510mm(?)
Hi! I also have bought airsoftpro zero trigger with 160 spring and airsoftpro hop up, but I have only 165 m\s. Do you use stock airsoftpro rubber or aftermarket one?
I use airsoftpro rubber, do you use 6.01 barrel? if u do, check if the piston oring match the cylinder =)
I use 6.02. Do you mean this prntscr.com/dx9p16 ?
at 6:22 this video, u see i greased the piston oring, check how it moves with the cylinder (to loose or to tight). that was a problem i had, mine was to loose only shot about 150-160 so i replaced it with a better match oring.
ok, thank you ! I will try change my o ring
Scipli e
Does the mbo3 come with a matal trigger box stock?
Zink alloy (metal)
Hello what spring force you use. thank you
Jan Kriz the power is the speed of meters per second with a .2 gram bb
Should I use a nine ball bucking (Hard)
ICY THUGS AIRSOFT I highly recommend using a maple leaf bucking but the nine ball purple is also good
How can I minimize the impact sound of the piston against the head of the barrel? I fucking love this vid bud. It really helped me a lot. And the screw thing u need to do, it also happened to me. Good job
Thx!, I tried before minimize impact sound by putting a customized rubber pad on cylinder head but again this affect the air flow, didnt turn good :P i dont know if there are any good way to do it =)
@Scipli Can you please give me a list of your upgrades.
I put it in description of the video =)
Why change the barrel? I thought the original barrel is already 6 mm?
The original barrel was 6.08mm, 6.03mm for more precision and slighty increasement of ms / fps.
Scipli Oh i see, thanks. Would u say the mb03 is better or the mb07? I'm having a hard time deciding...
I just scan the forum quick, seems like mb07 use VSR upgrades, u should dubble check =) , i would say, pick the one u find most beutiful =)
Scipli I see. For the list of upgrades you listed in the videi description, could you explain like what of them is for? For example, I know that you changed the stock M140 spring to an M170 spring for more power. But it'd be great too if you could explain the other components too (im newb lol)!
Trigger house, steel cylinder/head and piston is to keep durability/reliability when using stronger spring than original else the internals will break with m170 spring. Hopup house, rubber and barrel is to increase accuracy and muzzle velocity.
is it good for airsoft wars yes or no
how many did cost this upgrade ?
Around 200 Euro =)
I think it could be done with just a spring and a piston, airsoft triger and hop up (I think that pink cillinderish thingy) is just for being fancy.. But thats just mine opinion( Me just being amateur) ... Im waiting for a piston spring kit 35euro (Bcose im being cheap ).. Hope my nubmers gonna be close to yours.. I will reply later ;) Good luck...
@@zodziusavas Kaip upgradeas? Užteko pakeist spiruokle ir pistona ar dar kazka darei?
Hi! I also installed zero trigger v3 but I have problem ... when I pull back the bolt it is very hard ... like metal scrapes on metal ... Do you have the same problem?
Have not experience that problem, but check the screws so they are not scraping the cylinder. Trigger screws and those 2 screw holding the outerbarrel. Adjust with shims if the screws sits to high =)
thank you ) I know about screws but they aren't a problem 100%. I think sear scraps these parts prntscr.com/d52snw . i use a stock cylinder
Co2?
It has a spring so no spring powered
$ ?
did that say 180 or 190 fps??? that's a horrible sniper if that
it is m/s, 190m/s = 623 fps
Scipli oh, thx, is it bcuz I don't use metric system? Is FPS different? I am American.
FPS= Feet Per Second
1 Foot = 0,3048 Meter Per Second
M/S = Meter Per Second
1 Meter = 3,28084 Feet Per Second
191.4 M/S = 627,95276 FPS
BckW0Rdz he said 190 METERS u dummy
That is the same as 630 feet per second
Vell vell vell. En norman? Så biltema så er vell norman eller svenske xD?
Svensk xD
Du får arbeta på engelskan ;)
Näe hans engelska gick bra att förstå, åtminstone för mig!
Hopefully i diddnt just order a metal trigger box for no reason
Original trigger box is metal (aluminium/ zinc alloy), not suitable for heavy upgrades. I personally always go for steel sears to deal with heavy springs.
lol none of those parts are from stock gun
Witch is normal for a sniper even tm gets guttet and upgraded 😂🤣 then rather pay 60€ for a mb03 then 200+€ for a tm 🤣😂
M130?