⚠️⚠️additional info for those that have the early n47d20a, near the place you put the special tool on the pump you have a 10mm bolt that hold the pump. So to be able to remove it you got take out this one as well. Discovered by braking mine😂
very detailed video. I have replaced the high pressure pump and since then the engine light has been on. the car revs up to 4000 rpm. as soon as I press the pedal while in motion, there is an error. the full power of the engine is not possible. maybe the garage didn't install the right pump.
@xristospanagiotopoulos7401 Good luck to You sir! I hope you will solve this issue. And maybe You will tell us what it was later and perhaps by doing that You will help someone else too🤝🏻✌🏻
Hello Hint Slice, thank you for your video. I have a question what happens if you do not connect the wire, that you are connecting to the High Pressure pump, in 13:37 of your video and then tried to start engine with this wire (High Pressure Control Valve) unpluged? It will damage the high pressure pump?
I don't think you can damage H.P. pump in tha way because the pump in the fuel tank is pumping fuel in to the system when you start the engine. High pressure pump must be out of fuel completely to be damaged m.th-cam.com/video/08l3O8JueGo/w-d-xo.html
Thanks a lot for your explanation. I have a 2012 F11 that has never given me any problems so I took it to a workshop to change the timing chains. However, I was called to tell me that the van, after changing the chain, still worked for half an hour, they say, and then stopped and wouldn't start again, they looked at it and they said it was the diesel injection pump that fell apart in the engine and sent filings to the injectors and the diesel circuit. I want to ask if this problem can happen due to any negligence of the workshop? Thank you very much.
Do i need to replace injectors or can i just clean everything without changeing injectors? As i suspect my pump is bad. Getting limpmode around 2k RPM sometimes, But if i manual shift from 3k rpm i can ride every gear out without any problem, also cranking like 5 seconds before start. fault codes 004570 and 004560
In this case someone (but not me) dismounted injectors and intake manifold. But any way you need to dismount intake manifold so it would be more space to remove H.p pump. And theres no need to remove injectors and valve cover atleast you need to replace injectors or copper washers or valve cover gasket
I pinned comment from @BananaJulien2 months ago ⚠️⚠️additional info for those that have the early n47d20a, near the place you put the special tool on the pump you have a 10mm bolt that hold the pump. So to be able to remove it you got take out this one as well. Discovered by braking mine😂" So Yeah👍🏻
My cp4.1 has just fsiled f11 n47. Ppl say i must replace whole fuel system as metal will fit through the diesel filter. Whats your experience with that thought mate
first of all you need to check the injectors on the test bench for the damage and if injectors fail replace them. Then you will have to clean: all fuel lines, fuel tank, electric fuel pump in the fuel tank(most of the time electric pump is not damaged), change the fuel filter, change high pressure fuel pump, bleed the fuel system, start the engine and You Ready to Go.th-cam.com/video/qz_pTONZ3CU/w-d-xo.htmlsi=EAcRcWXPTx0aj5FJ
@@HintSlice I think the issue also is that the F10/11 saddle tank only opens on one side unlike your BMW. Any ideas on cleaning the side with no access?
@@caldwell1981ac First, what came to mind was to take it off and flush. A second option without removing the fuel tank is to try pumping out all the fuel with metal shavings and making something like a bigger version of the cotton buds to clean inside the fuel tank. Of course, if there is enough space to do this procedure.
@@glenspence6016 yes glen you need to remove the sprocket cover at the back of the engine. It's a 17mm spanner cap. Then insert fully the sprocket holding special tool. Then with tool in place remove the torque in the center remove pump. Timing tool remains untill new pump is fitted.
So recently had the dreaded cp4 hpfp give way on my 520d so have replaced pump with brand new unit,replaced injectors and cleaned out system. Car now runs however when i floor it, it throws up fault 247500 fuel pressure plausibility but goes away when car is stopped and restarted🤷♂️anyone experience this?
Hi. Do you install new injectors? Because i was reading about this fault and the reason was in one of the injector it was draining to much fuel in to te return line insted of supply and this fault apears like in your case when accelerating.
@@HintSlice hi fitted one brand new injector and 3 used injectors from a low mileage 13 plate 520. I took the car for another run this evening and hammered it up through the revs and it was absolutely fine so i’m hoping it was just a glitch🤞
Hi. I think taking off the throttle valve will give you more access to the h.p. ctrl valve . On 11:30 th-cam.com/video/qz_pTONZ3CU/w-d-xo.htmlsi=DOHMurwcZFdmeBGs
![BMW E87 2.0 diesel | Cleaning Fuel Tank after | N47 High pressure pump failure [Part 2]](http://i.ytimg.com/vi/qz_pTONZ3CU/mqdefault.jpg)
⚠️⚠️additional info for those that have the early n47d20a, near the place you put the special tool on the pump you have a 10mm bolt that hold the pump. So to be able to remove it you got take out this one as well. Discovered by braking mine😂
GOD bless you for giving us so many details about aligning the flywheel with that hole and the tool that works!
Thank you!
Thank you!
Thank You!
it's very cool that this helped you.
you're welcome.
Thank you so much for posting these videos. This video helped us change the hpfp
Thanks for the comment and it's cool that this video hepled You.
very detailed video. I have replaced the high pressure pump and since then the engine light has been on. the car revs up to 4000 rpm. as soon as I press the pedal while in motion, there is an error. the full power of the engine is not possible. maybe the garage didn't install the right pump.
Without computer diagnostic it's really hard to tell what causing the problem. And did they replace injectors also?
yes.I have changed all the air, fuel, AGR pressure valves.
Ok then only diagnosis can tell what is wrong
ok . thanks you mister.
@xristospanagiotopoulos7401 Good luck to You sir! I hope you will solve this issue. And maybe You will tell us what it was later and perhaps by doing that You will help someone else too🤝🏻✌🏻
Hello Hint Slice, thank you for your video.
I have a question what happens if you do not connect the wire, that you are connecting to the High Pressure pump, in 13:37 of your video and then tried to start engine with this wire (High Pressure Control Valve) unpluged?
It will damage the high pressure pump?
I don't think you can damage H.P. pump in tha way because the pump in the fuel tank is pumping fuel in to the system when you start the engine. High pressure pump must be out of fuel completely to be damaged m.th-cam.com/video/08l3O8JueGo/w-d-xo.html
Thanks a lot for your explanation.
I have a 2012 F11 that has never given me any problems so I took it to a workshop to change the timing chains.
However, I was called to tell me that the van, after changing the chain, still worked for half an hour, they say, and then stopped and wouldn't start again, they looked at it and they said it was the diesel injection pump that fell apart in the engine and sent filings to the injectors and the diesel circuit.
I want to ask if this problem can happen due to any negligence of the workshop?
Thank you very much.
@@pedromonteiro3288 if there was no intervention in the fuel system on their part, then I think that it may be a coincidence.
@@HintSliceThanks a lot for your clarification.
Best Regards,
Pedro Monteiro
@@pedromonteiro3288 I hope you will solve this problem peacefully. Regards
Great video.
Thank you
Do i need to replace injectors or can i just clean everything without changeing injectors? As i suspect my pump is bad. Getting limpmode around 2k RPM sometimes, But if i manual shift from 3k rpm i can ride every gear out without any problem, also cranking like 5 seconds before start. fault codes 004570 and 004560
to be sure you need to check the condition of the injectors on the injector testing stand (bench)
Do you have to take the valve cover and intake manifold off?
In this case someone (but not me) dismounted injectors and intake manifold. But any way you need to dismount intake manifold so it would be more space to remove H.p pump. And theres no need to remove injectors and valve cover atleast you need to replace injectors or copper washers or valve cover gasket
Thank you
It wont come off,does it need more power to come off or ?
Sprocket or pump?
@ i found it out,there was third 10 socket screw near the hole for special tool socket …
I pinned comment from @BananaJulien2 months ago
⚠️⚠️additional info for those that have the early n47d20a, near the place you put the special tool on the pump you have a 10mm bolt that hold the pump. So to be able to remove it you got take out this one as well. Discovered by braking mine😂"
So Yeah👍🏻
@ yes exactly the same screw,it was so good when i found it on forum … didnt even the read comments 😂
@@nikolamma I'm glad you found this bolt in time and didn't break anything.😄✌🏻
Thanks, can we do this at home? Without special tool?
Thank you too, yes you can but fuel pump gear won't come off without 118740 tool
My cp4.1 has just fsiled f11 n47. Ppl say i must replace whole fuel system as metal will fit through the diesel filter. Whats your experience with that thought mate
first of all you need to check the injectors on the test bench for the damage and if injectors fail replace them. Then you will have to clean: all fuel lines, fuel tank, electric fuel pump in the fuel tank(most of the time electric pump is not damaged), change the fuel filter, change high pressure fuel pump, bleed the fuel system, start the engine and You Ready to Go.th-cam.com/video/qz_pTONZ3CU/w-d-xo.htmlsi=EAcRcWXPTx0aj5FJ
@@HintSlice I think the issue also is that the F10/11 saddle tank only opens on one side unlike your BMW. Any ideas on cleaning the side with no access?
@@caldwell1981ac First, what came to mind was to take it off and flush. A second option without removing the fuel tank is to try pumping out all the fuel with metal shavings and making something like a bigger version of the cotton buds to clean inside the fuel tank. Of course, if there is enough space to do this procedure.
Hi can hpfp be replaced without timing tools as its on a keyway and the special tool holds the sprocket?? Many thanks
@@glenspence6016 yes glen you need to remove the sprocket cover at the back of the engine. It's a 17mm spanner cap. Then insert fully the sprocket holding special tool. Then with tool in place remove the torque in the center remove pump. Timing tool remains untill new pump is fitted.
What is the measurements of the special tool?
Any answer? The one in the kit I have is wrong?
Can you tell what is the number of your tool?
So recently had the dreaded cp4 hpfp give way on my 520d so have replaced pump with brand new unit,replaced injectors and cleaned out system. Car now runs however when i floor it, it throws up fault 247500 fuel pressure plausibility but goes away when car is stopped and restarted🤷♂️anyone experience this?
Hi. Do you install new injectors? Because i was reading about this fault and the reason was in one of the injector it was draining to much fuel in to te return line insted of supply and this fault apears like in your case when accelerating.
@@HintSlice hi fitted one brand new injector and 3 used injectors from a low mileage 13 plate 520. I took the car for another run this evening and hammered it up through the revs and it was absolutely fine so i’m hoping it was just a glitch🤞
@@glenspence6016 ok then, good luck on the road✊️
why do you need to secure and block the crankshaft?
So the chain timing can stay in place for sure, while slacken fuel pump bolt.
You can also hold the engine from the front pullys with a socket and rench to crack the fuel pump sproket bolt 👍
Hello
Is it possible to change the high pressure control valve without taking anything off? Or do I need to take something off in order to access it?
Hi. I think taking off the throttle valve will give you more access to the h.p. ctrl valve . On 11:30 th-cam.com/video/qz_pTONZ3CU/w-d-xo.htmlsi=DOHMurwcZFdmeBGs
Написано парт 1 , а где парт 2 ? Я не нашёл…
Ок. th-cam.com/video/qz_pTONZ3CU/w-d-xo.htmlsi=8En-jbeTGHBYdt51
Cp4 Bosch+Diesel=☠️
Invented for Life : )
Copper grease in an aluminium head 🤡🤡🤡
13 53 2 247 156