I just found a set of doors for my car, I go to TH-cam and ask how to do this, and BAM, there is Danny showing me how to do this. I cannot thank you enough for all you have done for mustang owners. I leave tomorrow morning to go get my doors and right front fender. Thank you and God bless brother
Hey Danny, I would like to talk to you on how to improve this video and fix the door adjustment without washers. I fixed my door this weekend and wanted to pass it on to you.
I just learned how to shim a new edge mustang door. The drivers side door on my Bullitt has been driving me crazy. I've done everything but shim it. Looks like I have a fix! Mine isn't that terrible that the door closes sloppy, it just droops... the body line is showing its age from all the years of use. Thank you for Sharing!
How do you do remove the wire harness on the drivers side? I suspect a broken wire for my passenger side power window in the drivers side bellows and was told to unplug the two clips behind the kick panel. Such a pain they seem to be right behind the gem module and all of its wiring bs. Is there an easier way to inspect wiring without totally destroying the bellows
Just crashed out and lost my pasanger door. Might be able to save her after watching this if the shop is able to bend the body back int place under the door
With those wheels(which you hardly see anymore), you should consider doing a 35th anniversary clone, I use to dig how they looked when new. I believe the centers of the wheels were painted argent and there was a honeycomb panel on the rear deck lid with a matte black stripe on the hood scoop to grille area.
Be very careful taking panels and bumpers off. There are plenty of factory shims that will fall out, so be sure to document them and put them back if possible. Just a tip.
Hi Danny, wonderful video on the fender removal and door alignment. Your video on the fuel pump installation helped me replace my fuel pump last fall on my 2003 mustang. My question is what size washers did you use for shims and are they metric or sae? They looked like wider ones. I was also wondering did you put them on the upper bolt of the lower hinge assembly or the lower bolt and did you use washers on both bolts? I was thinking you wouldn’t want to have a gap between the door and the hinge plate on one bolt. I have some sagging on my driver door and it bangs when shutting. Can I also remove the bolts without removing the fender by opening the door and bracing it? It looks like a lot easier access the way you did it. Any advice would be appreciated. Thanks, Kevin.
No, it’s called the quartet panel and it’s welded on. I once had a car that was in an accident and in order to fix it they had to order a whole new quarter fender piece and cut the old one off and weld them back together
It’s the bolts on front and rear by the tires and then the push pins and then push down. This guy also has a video th-cam.com/video/qO7UXKQ4P38/w-d-xo.html
![fellow fellow - PROUD feat. INK WARUNTORN [STRING QUARTET]](http://i.ytimg.com/vi/BQrVkMPTdHE/mqdefault.jpg)
I just found a set of doors for my car, I go to TH-cam and ask how to do this, and BAM, there is Danny showing me how to do this. I cannot thank you enough for all you have done for mustang owners. I leave tomorrow morning to go get my doors and right front fender.
Thank you and God bless brother
Hey Danny, I would like to talk to you on how to improve this video and fix the door adjustment without washers. I fixed my door this weekend and wanted to pass it on to you.
I learned so much from this... ive replaced the fender before but never the door harness... thanks
Jose Guido Thanks! I’ve never undone those harnesses until today.
I just learned how to shim a new edge mustang door. The drivers side door on my Bullitt has been driving me crazy. I've done everything but shim it. Looks like I have a fix! Mine isn't that terrible that the door closes sloppy, it just droops... the body line is showing its age from all the years of use. Thank you for Sharing!
More to come! Thanks for watching!
weight reduction nice
KyleSVT Those doors are super heavy lol.
How do you do remove the wire harness on the drivers side? I suspect a broken wire for my passenger side power window in the drivers side bellows and was told to unplug the two clips behind the kick panel. Such a pain they seem to be right behind the gem module and all of its wiring bs. Is there an easier way to inspect wiring without totally destroying the bellows
Just crashed out and lost my pasanger door. Might be able to save her after watching this if the shop is able to bend the body back int place under the door
Bringing it back to life.
charles taylor Little by little 🙌🏼
What about the driver side
With those wheels(which you hardly see anymore), you should consider doing a 35th anniversary clone, I use to dig how they looked when new. I believe the centers of the wheels were painted argent and there was a honeycomb panel on the rear deck lid with a matte black stripe on the hood scoop to grille area.
Yes, I actually just did a video on that. I’d polish them up but the center caps would be hard to match th-cam.com/video/GsDsfE1Wz3g/w-d-xo.html
Be very careful taking panels and bumpers off. There are plenty of factory shims that will fall out, so be sure to document them and put them back if possible. Just a tip.
Yeah, luckily on some there is some overspray and you can see where it went
@@dannyjohnsonsgarage Exactly because they surprised me building. I'm currently going through my project 2000 GT. Nice channel 👍
Awesome
Justin Johnson Thanks for helping me
Hi Danny, wonderful video on the fender removal and door alignment. Your video on the fuel pump installation helped me replace my fuel pump last fall on my 2003 mustang. My question is what size washers did you use for shims and are they metric or sae? They looked like wider ones. I was also wondering did you put them on the upper bolt of the lower hinge assembly or the lower bolt and did you use washers on both bolts? I was thinking you wouldn’t want to have a gap between the door and the hinge plate on one bolt. I have some sagging on my driver door and it bangs when shutting. Can I also remove the bolts without removing the fender by opening the door and bracing it? It looks like a lot easier access the way you did it. Any advice would be appreciated. Thanks, Kevin.
How long does it take to remove both doors? And install lambo hinges to a Ford Mustang
I need a video like this but for a 2014
How do you do the driver side door?
Where can I buy a right side door.? For a 2002 mustang
Salvage yards are the most affordable, then check late model restoration
Quick question when you switch out the driver side door how do you change the lock out
It’s all in there with the door panel off- this video will show most of it but it was on a passenger side th-cam.com/video/0wkFs1eWZ8E/w-d-xo.html
Would a base model door work on my gt (2002)
Yes. In fact, these are base model doors used in this video for my Gt
@@dannyjohnsonsgarage thanks 👍
Why would they make a job that can be so easy into a job that takes the whole day with one person
Engineers vs mechanics
is it possible to remove the rear fender? i cant find any videos on it
No, it’s called the quartet panel and it’s welded on. I once had a car that was in an accident and in order to fix it they had to order a whole new quarter fender piece and cut the old one off and weld them back together
Could i use this same concept on a 2008 mustang?
did you end up trying?
Is the left side the same?
Other than the harness location, which I believe is by the hood release?
@@dannyjohnsonsgarage I took the fender off and a lot of rocks and dust fell all over the place I’m mad now lol
Where did you purchase the doors from?
A salvage yard
we can't get the side skirt off, there doesn't seem to be anywhere to pinch it, 1997 not gt
It’s the bolts on front and rear by the tires and then the push pins and then push down. This guy also has a video th-cam.com/video/qO7UXKQ4P38/w-d-xo.html
What year is this
Mara Ginovin 2001, should be the same on 1994-2004 and most all Mustangs