@@bitsnbobs1969Be care-full , the capacitor will store a lot of power for hours even when unplugged. Touching a wire terminal will give you a dangerous shock or kill you! Buy a safe step-down tranformer, your life is worth more than 2 capacitors and 2 resistors!!
Simple Technic , good conversion of 230V AC to 110V AC, but please mention maximum current and wattage , so that we came to know useful for how many requirements.
Hi, congratulations I will definitely buy you a coffee. Can you show me which components you add to this circuit, in order to avoid that, when you remove the plug from the power point, the terminals of the plug discharge the current accumulated by the capacitors into your fingers. Thank you
sir the resistor you are use how many oum? and i have drill machine 580 watts is it ok if i use the same capacitor or no? i am waiting your reply for this questions. thank you
what if you want to ground the equipment? i have a preamp that is 110v on a 220v circuit, i have a transformer, but it has a 50hz hum noise, do you know how can i ground it? I dont want to wire it to the 220v ground
Capacitors and resistors alone did not work because I tried it, I have to add voltage control capacitor in parallel with the circuit before it work. I used it for my 110 v soldering iron. I tried to the same circuit for my GE electric range, because I believe oven section uses 110 v for the control board but the cooker plate use 220v
It work for me , what capacitor did you use? Was it CBB 250V 106J 10uf capacitor and 200K ohm resistors?may want to use resistor rate for at least 1watt
I have the same 110v Japan made soldering gun and I want to use it so eagerly but the problem is that I don't have a stepdown transformer. So I want to build a converter as shown in this video but you say you put a voltage control capacitor in parallel to this circuit.Could you help me with description of it in detail as I'm planning to build the converter,pls? Thanks in advance.❤
@@kraid1988 ну по таким примерным прикидкам, если сделать схему как в видио, то холостой реактивный ток будет 0,7А, и подключить нагрузку можно до 10Вт, при этом напряжение под нагрузкой должно проседать не более 10%. соответственно если кратно увеличивать ёмкость конденсаторов, то для 100Вт нагрузки и 10% уже ток холостого реактивного тока будет около 7А. В общем такую схему лучше не использовать, а если использовать то только если очень надо, только в одном устройстве в квартире (или частном доме), и на мощность до 15Вт.
икс цэ - ёмкостное сопротивление равно 2*пи*f*C, где f - частота в Герцах, С - ёмкость в микрофаррадах, для 10 микрофаррад и в сети 50Гц составит 163Ом, для более точных расчётов надо считать через комплексные числа.
@@boris9189how about connecting both outputs of the divider to the bridge rectifiers and then connect DC together to get half the voltage but in DC and then solder it just behind the rectifier bridge of the 120v device? Would that make it safe for higher current?
does it works like a voltage divider? that I can reduce the capacitance and resistance of the second junction to get lower voltage? also, how do you measure the capacitance and resistance required for the CD player wattage?
Well it's very simple and very good, can desk top pc with 110V, 50/60Hz, 6 Amps runs with the same caps and resistors from 230V ? Without damaging the pc circuits Thanks
If you get a voltage divider like this you will get a load dependent divider. Indeed, if you have a 110 Vrms 56W amplifier this is equal to roughly 200 Ohm, thus you put in parallel 200 ohm with 200k and so a final resistance of around 200 ohm in series with 200k -> around zero voltage for the amplifier. i am curious to read the voltage after the switch on
ps: you don't need to speak; just hold red/black in hand & then reverse, then give that rocking hand motion that designates equivalence. Bit more advanced as thumbs-up, but if youre going to do silent films, enlarge your sign vocab.... (pretty fresh comments for finding the exact simple solution i needed for my problem !=)
di naman pwede sa mga stereo amplifer gaya ng sakura or branded amplifier. ginawa ko ito sa technics stereo amplifier ko pero bumabagsak ang 110 volt supply pag i high volume ko. mas maganda pa yong transformer na may 220-110VAC
Sir it would be helpful if u tell us what it is u r going. I c u with some red 10uf device. But still don't know w6 to ask for at the electrical store.
Is it normal for capacitor to heat up? Im afraid it will melt, that is why i unplug it from my 220v source. And i notice too that at 1st it was 120v then after a while it became 170v while continue heating up. Can u enlighten me pls
👍👍. Cái này chỉ chạy công suất con con thôi nhỉ. Bạn thương mại luôn 1 cái mạch : 220v nắn lọc thành 310v. Sau đó cho qua bộ cầu H inveter và chỉnh , hồi tiếp các kiểu thành 110v. Vẫn sóng ~~ mà công suất hàng kw ấy chứ. Ngon hơn biến áp sắt là cái chắc.
@@Bdi. No, I could not Because I could not get this capacitor model None of the stores I asked have this capacitor In our country, almost everything has become scarce and even rare due to international sanctions.
My shop: bit.ly/PCBShop
Que bom se fosse tão simples assim... Primeiro conflito de tensão na entrada dos capacitores, torra tudo que nem churrasco.
Good thing is that circuit is simple. Bad thing is that if the capacitor is short circuited the equipment connected will be damaged.
The voltage drop across the capacitor is 110VAC. Capacitor withstand voltage is 630V.
Toca poner fucible por proteccion
@@PhdHung might be tempted to make one
@@bitsnbobs1969Be care-full , the capacitor will store a lot of power for hours even when unplugged. Touching a wire terminal will give you a dangerous shock or kill you! Buy a safe step-down tranformer, your life is worth more than 2 capacitors and 2 resistors!!
Also, if there is a tusunami he can damage too
wow i miss those days " made in japan "
Up to how much current in watts does it support?
100 ma
Do not be tired . How many ohms are these resistors? Thank you for your answer
1:08
Simple Technic , good conversion of 230V AC to 110V AC, but please mention maximum current and wattage , so that we came to know useful for how many requirements.
Thanks, but can't see the resister valiu
@@samanthisenadeera5054 dear friend you can use 220k - 390k Resistors easily
Sir max current kitna run kr saktye hy
100W only use.
@@rajpootfaiz3399 hafl watt
Can you make something like this for continuos 5000w input/output?
How I can make such a change for 550w use on electric appliances. Thanks.
☺️👍 RIGUARDANDOLO .... HO CAPITO GRAZIE MILLE SEI UN GRANDE 👏👏👏👏👏👏👏👏😡☺️
Thank you for giving me the lesson. 👍
thank you very much friend, people like You make this world better. Best regards
The resistors blow up 💥💥🔥 when I plugged 🔌the 230v AC !!!!!!!!!!
😂😅
I think he's fraud, he did not answered mostly questions
I think you used a very low resistant resistors, use a very high resistant resistor like from 150kOhms to 220kOhms.
It works perfectly.
@@imtel1He isn't.
Don’t mind him na lie is not working I try it isn’t working
Very good mounting, how many amps of current can it withstand?
at 210VAC 50Hz about 411ma, 122Hz needed for 1A
Hi, congratulations I will definitely buy you a coffee.
Can you show me which components you add to this circuit, in order to avoid that, when you remove the plug from the power point, the terminals of the plug discharge the current accumulated by the capacitors into your fingers. Thank you
I connected the capacitor with 2 resistors in parallel. when you unplug . The capacitor will discharge through the resistor.
@@PhdHung what reference are the resistors?
Don't worry and thank you How many ohms are these resistors? Please reply . Thank you ❤@@PhdHung
Why doesn't using of 110/120V from USA of my country???
Because low voltage means high current. More copper is used. Everything will be more expensive.
Good idea Sir, thanks for sharing. Does it work on hair dryer 110V supply?
No it will not
use one diod 6 A
Thanks for the tutorial! God bless! 🥰🥰🥰
Thank you for the info,.. but..what value are the resistors ?
sir the resistor you are use how many oum? and i have drill machine 580 watts is it ok if i use the same capacitor or no? i am waiting your reply for this questions. thank you
Only 100w sir..... dont do it...
Que buen video!!!! hasta "mi mamá puede hacerlo"
excellent video!!! "even my mother can do it"
THX!!
what if you want to ground the equipment? i have a preamp that is 110v on a 220v circuit, i have a transformer, but it has a 50hz hum noise, do you know how can i ground it? I dont want to wire it to the 220v ground
Nice job. Can you please let me know how warm the caps get if used to supply say a 50 watt 110v fan ?
Do you make it?
no the resistor is burn
Capacitors and resistors alone did not work because I tried it, I have to add voltage control capacitor in parallel with the circuit before it work. I used it for my 110 v soldering iron. I tried to the same circuit for my GE electric range, because I believe oven section uses 110 v for the control board but the cooker plate use 220v
Hola: que condensador colocaste.
It work for me , what capacitor did you use? Was it CBB 250V 106J 10uf capacitor and 200K ohm resistors?may want to use resistor rate for at least 1watt
I have the same 110v Japan made soldering gun and I want to use it so eagerly but the problem is that I don't have a stepdown transformer. So I want to build a converter as shown in this video but you say you put a voltage control capacitor in parallel to this circuit.Could you help me with description of it in detail as I'm planning to build the converter,pls? Thanks in advance.❤
Для малой мощности пойдёт, но если что-то большее подключать, то не пойдёт.
Примерно сколько можно до 100w ?
@@kraid1988 ну по таким примерным прикидкам, если сделать схему как в видио, то холостой реактивный ток будет 0,7А, и подключить нагрузку можно до 10Вт, при этом напряжение под нагрузкой должно проседать не более 10%. соответственно если кратно увеличивать ёмкость конденсаторов, то для 100Вт нагрузки и 10% уже ток холостого реактивного тока будет около 7А. В общем такую схему лучше не использовать, а если использовать то только если очень надо, только в одном устройстве в квартире (или частном доме), и на мощность до 15Вт.
@@boris9189 спасибо
икс цэ - ёмкостное сопротивление равно 2*пи*f*C, где f - частота в Герцах, С - ёмкость в микрофаррадах, для 10 микрофаррад и в сети 50Гц составит 163Ом, для более точных расчётов надо считать через комплексные числа.
@@boris9189how about connecting both outputs of the divider to the bridge rectifiers and then connect DC together to get half the voltage but in DC and then solder it just behind the rectifier bridge of the 120v device? Would that make it safe for higher current?
does it works like a voltage divider? that I can reduce the capacitance and resistance of the second junction to get lower voltage? also, how do you measure the capacitance and resistance required for the CD player wattage?
سُبْحَانَكَ اللَّهُمَّ وَبِحَمْدِكَ ، أَشْهَدُ أَنْ لا إِلَهَ إِلا أَنْتَ ، أَسْتَغْفِرُكَ وَأَتُوبُ إِلَيْك.َ^-^
Well it's very simple and very good, can desk top pc with 110V, 50/60Hz, 6 Amps runs with the same caps and resistors from 230V ? Without damaging the pc circuits Thanks
Small good work What capacitor value
10uF bro
awesome tech you now have spirits in your video only voice
If you get a voltage divider like this you will get a load dependent divider. Indeed, if you have a 110 Vrms 56W amplifier this is equal to roughly 200 Ohm, thus you put in parallel 200 ohm with 200k and so a final resistance of around 200 ohm in series with 200k -> around zero voltage for the amplifier. i am curious to read the voltage after the switch on
I agree with you
The 200k is for safety and equalization to discharge the capacitors. The capacitor resistance Zc=1/(2*3.14159*f*c) ;f=50 or 60; c=capacitance
@@imcrazy886 ok, in this way the loaded system is still unbalanced after turn on if the capacitors are the same
dear friends can we operate 110v microwave oven tranformer from this circuit....?
can anyone reply me please.
what are the disadvantages of using that for 110v? is that safe for mini sound?
Hi, good, can you tell me how to electronically discharge the capacitors after you have used 110V voltage for any appliance used? Thank you
Most probably the resistors below the capacitors will do it automatically..
@@angsry what amount are the resistors?
@@Mahdawy11 For 400v PF capacitor 1M ohm qtr watt resistor works.
Good and great job please make AC voltage multplier or doubler
Its just a simple voltage divider. The question is how much power it can deliver
Sir, you mention the resistor value please. Thanks
1:08 You were not paying attention.
Does this inverter work in both directions? I have a 120v power supply and I need to connect a 220v fan... Does it apply?
it just reduces the voltage.
thats great................ but how much watts this thing can handle..............................
Gracias por su valiosa ayuda.
Is it dangerous or not ?
Can it function with a refrigerator?
Pinter pinter gagu😂😂😂
It is possible to use the same way for 500W purpose.
Hello! What is the maximum current electricity/ampegare or power in Watt for this? Thanks.
Nice work ❤
kash aap awaz ke sath video banatey takey hr kisi ko samjh m ati
How much labor can be obtained from this circuit? W
~ 100W
Berapa watt resistor nya?
Dan berapa watt maksimal beban yang dibolehkan alat ini?
How many ohm resistors did you use?
He showed 200K resistor
it is posible to use in grinder and drill 110v..and wt is s value of the resistor thanks
What is the value of the resistor pleas indicate the value
great video.
Thanks
@@PhdHung good video, what is the wattage rating of you 200K resistor?
Sir ji resistor kitne value ka hai aur watt kitna hai
ps: you don't need to speak; just hold red/black in hand & then reverse, then give that rocking hand motion that designates equivalence. Bit more advanced as thumbs-up, but if youre going to do silent films, enlarge your sign vocab.... (pretty fresh comments for finding the exact simple solution i needed for my problem !=)
How much max watt ? I want 200 watt this will work good or it’s less than 200 watt
Whats the value of the resistor? 800k?
di naman pwede sa mga stereo amplifer gaya ng sakura or branded amplifier. ginawa ko ito sa technics stereo amplifier ko pero bumabagsak ang 110 volt supply pag i high volume ko. mas maganda pa yong transformer na may 220-110VAC
Sir it would be helpful if u tell us what it is u r going. I c u with some red 10uf device. But still don't know w6 to ask for at the electrical store.
How many W can get with this 110vac outlet?
if you use 16uF capacitors . Maximum power is about 100W.
How many watts does it support?
Is it normal for capacitor to heat up? Im afraid it will melt, that is why i unplug it from my 220v source. And i notice too that at 1st it was 120v then after a while it became 170v while continue heating up. Can u enlighten me pls
Use a larger capacity capacitor. The voltage will be more stable.
@@PhdHung any suggestion sir how much capacity is larger? How about the 200k resistor? Am i gonna replace it too? Can u give me the right combi? Thanx
dear friend can we operate 110v microwave oven tranformer from this circuit Or please tell me some way by which I can run 110v transformer to 220v.
It work but may cap damage then you will take over voltv
Se podrá utilizar para un motor tool , trabajará normal?
It can be used for rice cooker 110 volts?
no,you need a transformer at least 1500VA
Resistor value?
Sir how can make a UPS or stabilizer to perform 110v 60 hz from 220v 50 hz
how u convert 50hz to 60hz? thank u!
Rasestens ki value kya thi
Bro upload you old videos please don't delete your old video
Will this apply to Integrated Amps too?
What is the value of the resistor
What values of this component used
👍👍. Cái này chỉ chạy công suất con con thôi nhỉ. Bạn thương mại luôn 1 cái mạch : 220v nắn lọc thành 310v. Sau đó cho qua bộ cầu H inveter và chỉnh , hồi tiếp các kiểu thành 110v. Vẫn sóng ~~ mà công suất hàng kw ấy chứ. Ngon hơn biến áp sắt là cái chắc.
Dàn loa chạy có 60W thôi b :D .
@@PhdHung cái loa tính gì. Ý là chạy độ 110v hàng vài trăm W ấy chứ.
nắn từ 220VAC xuống 110VAC nó nóng lắm. phải buck 310VDC xuống tầm 200VDC rồi mới băm sine ra 110V thì hiệu suất mới cao đc.
Thì như mình nói từ đầu: 220v lưới chỉnh lưu và lọc đã thành 310vdc rồi. Sau đó qua cầu H và xuống 110v ấy.
@@quanghoang04 310VDC xuống 110AC nó bóp nhỏ duty lại nên nóng van bán dẫn lắm. Buck xuống 200VDC rồi mới băm bạn à.
Hey bro..I want for 200 watt..Plz give an idea Reply plz
LOL what about the transformer under the desk!!
Nice video
SIR HOW MUCH MAXIMUM CURRENT OUTPUT.OF THIS CIRCUIT.
I want to stepdown my 120AC microwave rates 1,500 watt from 220 V ac source . Is a capacitor is the answer
Pls what is the resistor value ?
200k
How many watts are those resistors?
Value 106 , and 250volt
@@kaylanadhifachannel8817 I mean those tiny 200K resistors , how many watts are they?
Akhirnya cari kmna" ketemu juga
Kapasitor itu sama gak sama audio filler yg warna kuning?
Hi, i have a question about yourconverter, is it possible to turn on a kitchenaid rebot of 2000W /110V or not ?
no bro. max
Why not? You can! But it won't work.
@@leninoble hi dear friend, I also want to run microwave 1500-2000w transformer 220v - 110v
@@leninoble dear friend can you help me in this matter kindly reply me as soon as possible
I have honda eu22i generator 220V and i want to use mai tools which is 110V. It is possible?
Very nice Vedio
Эта схема потянет швейную машинку 100вольт 100ват 3 ампера?
Is possible to connect a stuffed to koking
no bro. Only 100W
Amei👏👏👏👏👏👏👏😍😍😍😍
Of 106j ki jagah 105 j kaam karega kya
Woow nice
😍😍😍
Me gustó la explicación del video, en lenguaje mudo me supongo
Bro do you formula how to convert to 110v
para una nevera sirve o habrá que hacer modificaciones recordando que el consumo constante de un compresor es de 1.5 a 4 amperios (no inverter)
no sirve eso solo entrega 100w de potencia y al maximo..
super
Thanks
my cassette deck is 100 volt but in my country it's input source is 220 volt.... will it work by this method without adding 220 volt transformer??
hello sir . did you try it? i want to know are you succes?
@@mm3mosen no I would not... I won't risk for my precious cassette deck.. rather buy volt changer
@@altanphedap6361 ok great job!
but i I have to make it because the power converter or volt changer is very expensive here
@@mm3mosen have you make it?
@@Bdi. No, I could not
Because I could not get this capacitor model
None of the stores I asked have this capacitor
In our country, almost everything has become scarce and even rare due to international sanctions.
How many watts it can provide ?
ano yung nilagay sa gitna boss? diode ba yun?
can i use fan capacitor like 450v 10uf to replace this cap
ok bro
Is this very good and save for one light bulb 60w?
Excelente, thank you very much.
Very good thanks.