Thanks very much for sharing your expert knowledge. I had to watch your tuning method several times before I released that what you are showing is really a very simple method to fairly quickly obtain a good tune. I tried to take a short cut on your method and started the process using my current reg settings of 85 bar but found that I was way up on the plateau. I was amazed to find the knee (at an acceptable sub 12 fpe) with the reg pressure set at only 55 bar. This is lower than the reg pressure set by the UK importers when I first got the gun. I now realise that I need to be careful about following advice on airgun forums - someone, who I thought was knowledgeable, advised me to increase the reg pressure to at least 80 bar and then reduce the HST to achieve sub 12. I had been using this setting for some time and wondered why my Crown was shooting poorly at 50 yards. I'm confident that I'm going to get much better results with my new tune (not shot it yet but the tune resulted in a very low standard deviation). I had previously tuned/fettled my regulator, trigger, hammer, pellet liner etc (mainly following other videos of yours) and my Crown is rapidly improving. One thing I would add for others who are tuning for sub 12 is to use a pellet that you know produces a high fpe. That way you should find that your rifle remains sub 12 when using other pellets after the tune.
This is the method that I adopted too when I started tuning my Streamline FAC and Dream-Tac FAC. This is a proven way of tuning a pcp for low spread and efficiency. That said, this is the first time that I see it explained in such a clear way. Awesome video. I have subscribed and will direct others to your channel every time I see people struggling with their setup. Add: once I have found the plateau velocity, I reduce the HST until the velocity is ~2.5% below the plateau velocity and fire 10 shots to see how it groups. If not great, then I slightly increase or decrease the HST until I find the best tune. Sometimes I have to slightly increase or decrease the reg pressure to find the sweet spot in terms of accuracy and efficiency (I'm not interested in very high power, only in accuracy).
Thanks, that's the way we do it, this gets you around where you need to be then fine tuning the reg and hammer spring for accuracy, it takes a little time but well worth doing in my opinion. Thanks for watching.
Good luck Phil, its tricky to get the balance right but worth the effort in the long run. As long as it doesn't turn into a javelin down the range ill be happy. Thanks for watching.
Great video, was looking for a sub12 tune on an FX, for a while now. I have a Dreamline which is a bit inconsistent and with an FPS increase of a few shots after tank pressure drops below reg
Thats a fairly common problem to be honest but not a big deal you should be able to wind off a couple of turns on your hammer spring, and see little to no drop in power, as your hammer spring setting is overpowering the valve. Thanks for watching.
@@sub12airgunners did use your info to fine tune my Continiuum in 22 with 50 cm liner to 50J with the 18.13 JSB. Will see how it goes next Saturday. Outdoor 100 mtr range.
Jeff seen others set hammer spring cam to neutral so cam only starts to move spring at min plus .5. Then set hammer to max and adjust reg till 20 FPS above desired and then reduce hammer spring to desired FPS ! Check out Ken Hikes and Ernest Roe, seemed much quicker to do.
You can do it that way no problem, but this video was more on the theory of tuning and not just showing the quickest way to do it, any rifle FX or other wise can be tuned in this method, we started out with no predetermined knowledge and found using repeatable methods the base pressure for the regulator and a suitable hammer spring setting, in reality when not tuning for the camera, we can setup a crown for range testing in 5 mins flat, but the concept and tuning method is the idea of this video. Thanks for watching.
I’m not confident enough yet to work on my Crown like you have demonstrated but this was a really interesting and informative video, thanks. It’s very encouraging to see your results in the second video. You mentioned a link, but I cannot find it, are you able to still link please as having something to read would be very helpful. 👍🏽
So when you taking saying your turning the hammer spring up... this is when you use the Alan key on the hammer spring yes?? If so would have been nice to see this process
Outstanding. Great video and A lot of valuable information's Explained well in a simple way . i have a question. can i tune a without FAC specification MK II crown in a same way? please reply .
Awesome video I do the same thing as well but I shoot my gu. At 1000fps 32.8 varmint knockers slugs in 22cal with 700mm its a beast 💪 of a gun very consistent high reg pressure 160bar
Hi great video as I've just got my first FX (Crown mk 2) and trying to tune it but when I have taken it apart at 9.56 you say you need a 2.5 mm Allen key but in that position I've just a plastic black cap so unable to adjust? Or can I remove the cap?
@@sub12airgunners That's great thanks for the info, been asking on facebook groups and everyone is talking about power adjust but could not see it, i think they though I was a bit mad lol. Appreciate the info, no warranty as second hand anyway 🙂
Great video. Are there any plans to do an impact mk2 sub12 tune? As I'd love pointers on getting the best from mine and all other vids are geared towards the FAC world
do we really need to remove the power wheel to just tweek the HST as im not to clever on the tools mate to be honest i just want to give it a half tweek in if that makes sense please advise cheers
Hi, Could this method be used to tune the Maverick? Finally got mine over a chrono and it's woefully short on power......Reading 8ft lbs from factory which is astonishing. Also its leaking air. If this is what £1400 gets you I'm not very impressed at all. Think a phone call to the dealer is in order but just wondered your thoughts? Many thanks
The methodology is applicable to any pcp. I don't have a Maverick but I think you are better off leaving the 1st reg (the high pressure reg) alone and just focus on the 2nd reg.
I have an FX crown Blue Laminate and it suffers from massive reg creep despite me rebuilding the reg with new seals. I have also been told by a reg man that this is one of the most common problems with the Crown. Is there any way I can get reg creep down to manageable levels?
We polish both sealing surfaces of the reg this helps tremendously, it does not eliminate it completely but it brings it down to manageable levels, the top of the reg piston and the bottom of the reg adjuster are the sealing surfaces in the AMP regs so we get them to a mirror polish and they seal up nicely. Thanks for watching
Thanks very much for sharing your expert knowledge. I had to watch your tuning method several times before I released that what you are showing is really a very simple method to fairly quickly obtain a good tune. I tried to take a short cut on your method and started the process using my current reg settings of 85 bar but found that I was way up on the plateau. I was amazed to find the knee (at an acceptable sub 12 fpe) with the reg pressure set at only 55 bar. This is lower than the reg pressure set by the UK importers when I first got the gun. I now realise that I need to be careful about following advice on airgun forums - someone, who I thought was knowledgeable, advised me to increase the reg pressure to at least 80 bar and then reduce the HST to achieve sub 12. I had been using this setting for some time and wondered why my Crown was shooting poorly at 50 yards. I'm confident that I'm going to get much better results with my new tune (not shot it yet but the tune resulted in a very low standard deviation). I had previously tuned/fettled my regulator, trigger, hammer, pellet liner etc (mainly following other videos of yours) and my Crown is rapidly improving. One thing I would add for others who are tuning for sub 12 is to use a pellet that you know produces a high fpe. That way you should find that your rifle remains sub 12 when using other pellets after the tune.
Why skip
all and any knowledge is good in my 61 years always learning thankyou for sharing 😁
You are very welcome, Thanks for watching.
This is the method that I adopted too when I started tuning my Streamline FAC and Dream-Tac FAC. This is a proven way of tuning a pcp for low spread and efficiency. That said, this is the first time that I see it explained in such a clear way. Awesome video. I have subscribed and will direct others to your channel every time I see people struggling with their setup. Add: once I have found the plateau velocity, I reduce the HST until the velocity is ~2.5% below the plateau velocity and fire 10 shots to see how it groups. If not great, then I slightly increase or decrease the HST until I find the best tune. Sometimes I have to slightly increase or decrease the reg pressure to find the sweet spot in terms of accuracy and efficiency (I'm not interested in very high power, only in accuracy).
Thanks, that's the way we do it, this gets you around where you need to be then fine tuning the reg and hammer spring for accuracy, it takes a little time but well worth doing in my opinion. Thanks for watching.
A very helpful and enjoyable video, young man. 👍
Thank you kindly! Thanks for watching
Excellent video, Im going to give this technique a try on my dreamline.
Looking forward to the results 👍
Good luck, thanks for watching.
That was great Jake, I now realise the relationship between the regulator and hammer spring , I'll be using that method to set up the stressgun 😁😂
Good luck Phil, its tricky to get the balance right but worth the effort in the long run. As long as it doesn't turn into a javelin down the range ill be happy. Thanks for watching.
Great video, was looking for a sub12 tune on an FX, for a while now. I have a Dreamline which is a bit inconsistent and with an FPS increase of a few shots after tank pressure drops below reg
Thats a fairly common problem to be honest but not a big deal you should be able to wind off a couple of turns on your hammer spring, and see little to no drop in power, as your hammer spring setting is overpowering the valve. Thanks for watching.
Thanks for sharing and excellent explanation.
You are welcome! Thanks for watching.
Muito bom o ganho de VO e energia com as regulagem do martelo e da disparadora, excelente .
Thanks, very much appreciated. Thanks for watching.
Great video mate thanks for this it’ll help a lot of people 😊👍
Hope so! Thanks for watching.
Really good video, keep up the good work. 👍👍👍👍
Thanks, will do! Thanks for watching.
Very informative, thanks.
Thanks for watching!
Very good info, thank you
Glad it was helpful! Thanks for watching.
@@sub12airgunners did use your info to fine tune my Continiuum in 22 with 50 cm liner to 50J with the 18.13 JSB. Will see how it goes next Saturday. Outdoor 100 mtr range.
very informative cheers bud
No problem 👍. Thanks for watching.
Very informative 👏👏👏
Glad you think so!
Jeff seen others set hammer spring cam to neutral so cam only starts to move spring at min plus .5. Then set hammer to max and adjust reg till 20 FPS above desired and then reduce hammer spring to desired FPS ! Check out Ken Hikes and Ernest Roe, seemed much quicker to do.
You can do it that way no problem, but this video was more on the theory of tuning and not just showing the quickest way to do it, any rifle FX or other wise can be tuned in this method, we started out with no predetermined knowledge and found using repeatable methods the base pressure for the regulator and a suitable hammer spring setting, in reality when not tuning for the camera, we can setup a crown for range testing in 5 mins flat, but the concept and tuning method is the idea of this video. Thanks for watching.
I’m not confident enough yet to work on my Crown like you have demonstrated but this was a really interesting and informative video, thanks. It’s very encouraging to see your results in the second video. You mentioned a link, but I cannot find it, are you able to still link please as having something to read would be very helpful. 👍🏽
Yep the second vid is on the channel, link below, thanks for watching.
th-cam.com/video/hqjNBV2yBZ0/w-d-xo.html
Ah, I thought there was a weblink to some sort of post that I could read☺️ Thanks, my mistake.
👍
nice job 👌👏
Thanks for watching 👌
So when you taking saying your turning the hammer spring up... this is when you use the Alan key on the hammer spring yes?? If so would have been nice to see this process
Outstanding. Great video and A lot of valuable information's Explained well in a simple way . i have a question. can i tune a without FAC specification MK II crown in a same way? please reply .
Awesome video I do the same thing as well but I shoot my gu. At 1000fps 32.8 varmint knockers slugs in 22cal with 700mm its a beast 💪 of a gun very consistent high reg pressure 160bar
Very nice, its a good method. Thanks for watching.
Not sub 12 foot pound then !
Do you tune rifles for a fee?
Hi great video as I've just got my first FX (Crown mk 2) and trying to tune it but when I have taken it apart at 9.56 you say you need a 2.5 mm Allen key but in that position I've just a plastic black cap so unable to adjust? Or can I remove the cap?
that will just pick out with something sharp then you can adjust but it will void your warranty if you remove it
@@sub12airgunners That's great thanks for the info, been asking on facebook groups and everyone is talking about power adjust but could not see it, i think they though I was a bit mad lol. Appreciate the info, no warranty as second hand anyway 🙂
Great video. Are there any plans to do an impact mk2 sub12 tune? As I'd love pointers on getting the best from mine and all other vids are geared towards the FAC world
Yep, Impact tuning vids are on the cards, not sure when but they are defiantly coming. Thanks for watching.
@@sub12airgunners I will happily send you mine to do, even use it in a video haha
do we really need to remove the power wheel to just tweek the HST as im not to clever on the tools mate to be honest i just want to give it a half tweek in if that makes sense please advise cheers
unfortunately on the Crown you do have to to get the stock off, but it is very simple to do
@@sub12airgunners lol ok thanks still I wouldn’t trust myself cheers for answering mate
Hi, Could this method be used to tune the Maverick? Finally got mine over a chrono and it's woefully short on power......Reading 8ft lbs from factory which is astonishing. Also its leaking air. If this is what £1400 gets you I'm not very impressed at all.
Think a phone call to the dealer is in order but just wondered your thoughts? Many thanks
The methodology is applicable to any pcp. I don't have a Maverick but I think you are better off leaving the 1st reg (the high pressure reg) alone and just focus on the 2nd reg.
I have an FX crown Blue Laminate and it suffers from massive reg creep despite me rebuilding the reg with new seals. I have also been told by a reg man that this is one of the most common problems with the Crown. Is there any way I can get reg creep down to manageable levels?
We polish both sealing surfaces of the reg this helps tremendously, it does not eliminate it completely but it brings it down to manageable levels, the top of the reg piston and the bottom of the reg adjuster are the sealing surfaces in the AMP regs so we get them to a mirror polish and they seal up nicely. Thanks for watching
Will doing any of this invalidate my warranty?