Best video i've found on this problem! I bought the first incorrect actuator as you did , except from napa. So then I removed the old one for them to reference . The new one was defective from the factory. As was the next new one I returned it for. On my 4th trip to Napa I stopped by Advance and picked one up. Same brand, different box , worked correctly. If your doing this, test that actuator BEFORE you buckle things up!
Thanks Much for instructions!. I did cut the key the turns the blend door 1/4"inch which made it easier to reinstall. The job took one hour to complete removing the console and air vent below the blend actuator. I did have all the tools you mentioned so that too was a big help. I saved a ton of money like did...thanks again.
@@davegreenwood2174 the blend door(flap) that opens and closes from heat to cold. If you have the module out the female slot the key fits turns one way othe other. I just didn't want to struggle with the tight fit getting the module back in place.
Thanks for vid, easy to follow. I would make a note about the actuator post not lining up and having to replace it. Out of the box my Dorman actuator post looked just like yours and I thought I might have to return it. I realized though, like you, my blend door was stuck in the cool position. The actuator arrived in the warm position. I turned the dash dial to warm, plugged in the new actuator and spun the dial to cool. The post slowly spins to the correct cool position and I was able to install. I can't be certain this is the same in everyone's case but it worked for me and maybe it will save future installers the aggravation of returning parts. Good luck.
I loved watching your video I’m a single mom and I’m gonna try this tomorrow I’ve had a exact same problem you do and I’m hoping I can get this to work! I have to say your video is very own detail about things that I need to know since I don’t know what I’m doing but I most certainly can’t afford the $500 I was told it would cost me with a mechanic I will post a update tomorrow evening
@@chophosho5935 it worked!!!! Got it done within about an hour in a half lol the hardest part was actually putting the new part back in!! But it worked! Thank you so much for your video all your tips helped!💙
I have this problem in the rear but I watched this to familiarizes myself with what might be similar. You thought of everything as you made this great video. Probably the best instructional video I've seen on you tube. Great job and thanks for sharing your experience. Folks like you are the reason I watch youtube.
Nice job. I'm doing one and have been on it for over a day...about 3 hours into it. Have the tools and today will pull actuator out and get it done. I do have big hands....lol...but will not give in. Informative video...thanks for sharing.
I just did this on a 2004 Ford Explorer and it did fix it, not too bad at all, the trick with the tape holding the bolt to put back in was a good trick too
Thanks for the video. I was able to get this done for a guy in 2 hours exactly. I used a cordless impact on all the bolts to speed up the process. Then I used a 4-5 inch non ratcheting 8mm wrench. Getting the 3 actuator screws out and all back in was 1.5hrs of the 2. I got all 3 in but if you’re a big guy it’s not happening
Wow! Even though I don’t hafta do this, I pretty impressed that you undertook to research and video every step. Ya done good. You kinda paved the way for every other person that has limited knowledge about this issue. I really appreciate that you showed it on your ride, warts ‘n’ all....haha ...time + perseverance = $$$avings, thanx.
If you plug in the electrical connector to the new actuator before installing, then turn the ignition switch to the on position, you can set the actuator post position by turning the dashboard cold hot switch position.
I have a 2002 Sport Track. This video as well as many others on simular Ford models does me no good. Although many of the videos I've watched usually have the blend door actuator in the same location ( on the base board right of the steering column) and advise the removal of the center console for replacement. Mine is not in that location. And how do I know. I removed the center console! Yeah bummer! My mechanic said it was there as well as my shop manual I bought from Ford Administrative Department in Dearborn, Mi. At least that's where it claimed to have come from. Mine is located above the glove box. And it seems as if is an easy fix. But it is not! The front two 7mm are easy to access but the one in the back is very difficult. It appears it requires a special tool, little dexterous hands, or removal of the whole dashboard. So for those of you that may have a model slightly different, LOOK BEFORE YOU LEAP!!! And this includes if you are considering having it repaired y a mechanic. If you don't labor charges can be added based upon bad information.
The two different shafts are for a mid year design change, which Ford is famour for. There'e an early and a late model for the '02 Explorers and I believe the build date is March 3, 2002.
I understood exactly what you were saying and after your video, it seems to be straight forward. But, I'm wondering how you managed to crawl under the dash like that. By feel I finally removed the two lowers screws and the electrical plug. And then, by feel again, I tried to put a 8mm socket (1/4" drive) onto the top screw. I'm still working on that one. In one way it's not a hard job, just hard to get at and at my age crawling under the dash is a task in of itself. I think I'll call me grandson for the one screw.
Just curious, when you demonstrate at the beginning, turning heat dial to full heat, i noticed your "A/C" button light is on, Why would it be on? I have the 2005 explorer and no problem,so far, but usually when i turn cooler on i press the A/ C button, similar to your year/ model, and cold air is coming out after i press it on.
After doing this it will come out the vents properly now,but if I turn to only defrost hardly any air comes out of the vents up on dash. Where I had opposite problem before as it only came out on dash. Any ideas.
Mine does the same thing. I took my vehicle to a mechanic and they said there is 4 blend door actuator's and they have to spend five hours trying to figure out which one went out and 10 more hours fixing it sounds like bs
i did take longer than you did but that was because i was frustrated on getting the actuator out. Now i was able to get the new one in and plug in the electronic connector all inside of an hour (i was pretty proud of myself that morning). Now i'm wondering if i put the actuator in incorrectly (common sense tells me that because of how the post is designed there was only way it could go in. i'm in doubt now because now my a/c doesn't work now and it worked just fine a few days ago and now all i'm getting is hot air no matter if i turn the dial to A/C or Heat. i looked at your video so i know you haven't had this problem. i don't want to put my console back together just to dismantle her again.
Hey sorry for replying so late. The groves on the actuator is such that there is only one way to put it in. If you put it in the the wrong orientation in wont push through. Hope you were able to pull it off.
Which you probably said it but what year explorer you have I have a 04 I'm thinking about trying to do is the process the same and yes it has that button up front on the center console everyone I contact to try and get fix saying I would have to drop the whole dashboard and can cost to 1000 dollars
Omg ty so much I just got done putting the new actuator in was a little rough once to got to the actuator itself but it work let there be heat lol tx buddy definitely giving you a like and you just gain a new subscriber saved me 1000 dollars what the dealer and local mechanics was asking to do the job great job and video
Best video i've found on this problem! I bought the first incorrect actuator as you did , except from napa. So then I removed the old one for them to reference . The new one was defective from the factory. As was the next new one I returned it for. On my 4th trip to Napa I stopped by Advance and picked one up. Same brand, different box , worked correctly. If your doing this, test that actuator BEFORE you buckle things up!
Glad to hear you were able to fix it 👏
Thanks Much for instructions!. I did cut the key the turns the blend door 1/4"inch which made it easier to reinstall. The job took one hour to complete removing the console and air vent below the blend actuator. I did have all the tools you mentioned so that too was a big help. I saved a ton of money like did...thanks again.
What is the flap your speaking of ? The stem is in a different position on the new part .
@@davegreenwood2174 the blend door(flap) that opens and closes from heat to cold. If you have the module out the female slot the key fits turns one way othe other. I just didn't want to struggle with the tight fit getting the module back in place.
Dear Sir, your video is absolutely perfect and allowed us to fix the issue prior to drive to the mountains. THANK YOU! Best.
For future reference, avoid using any parts from Dorman. Great video. It was very useful. I'm going to change my blend door actuator this week.
Good to know. Good luck with repair 👍🏻
@@chophosho5935 The repair turned out great.
Thanks for vid, easy to follow. I would make a note about the actuator post not lining up and having to replace it. Out of the box my Dorman actuator post looked just like yours and I thought I might have to return it.
I realized though, like you, my blend door was stuck in the cool position. The actuator arrived in the warm position. I turned the dash dial to warm, plugged in the new actuator and spun the dial to cool. The post slowly spins to the correct cool position and I was able to install.
I can't be certain this is the same in everyone's case but it worked for me and maybe it will save future installers the aggravation of returning parts. Good luck.
I loved watching your video I’m a single mom and I’m gonna try this tomorrow I’ve had a exact same problem you do and I’m hoping I can get this to work! I have to say your video is very own detail about things that I need to know since I don’t know what I’m doing but I most certainly can’t afford the $500 I was told it would cost me with a mechanic I will post a update tomorrow evening
Let me know how it goes!
@@chophosho5935 it worked!!!! Got it done within about an hour in a half lol the hardest part was actually putting the new part back in!! But it worked! Thank you so much for your video all your tips helped!💙
I have this problem in the rear but I watched this to familiarizes myself with what might be similar. You thought of everything as you made this great video. Probably the best instructional video I've seen on you tube. Great job and thanks for sharing your experience. Folks like you are the reason I watch youtube.
Thanks for watching!
Hey did u ever fix the rear clicking nosie
Nice job. I'm doing one and have been on it for over a day...about 3 hours into it. Have the tools and today will pull actuator out and get it done. I do have big hands....lol...but will not give in.
Informative video...thanks for sharing.
Thank you. I fixed mine through watching your vid! Well done
Glad it helped
Thank you!!! With all your tips take me one hr🙏🙏🙏
I just did this on a 2004 Ford Explorer and it did fix it, not too bad at all, the trick with the tape holding the bolt to put back in was a good trick too
Thanks for the video. I was able to get this done for a guy in 2 hours exactly. I used a cordless impact on all the bolts to speed up the process. Then I used a 4-5 inch non ratcheting 8mm wrench. Getting the 3 actuator screws out and all back in was 1.5hrs of the 2. I got all 3 in but if you’re a big guy it’s not happening
The ratchet was very helpful. Thanks for posting
Wow! Even though I don’t hafta do this, I pretty impressed that you undertook to research and video every step. Ya done good. You kinda paved the way for every other person that has limited knowledge about this issue. I really appreciate that you showed it on your ride, warts ‘n’ all....haha ...time + perseverance = $$$avings, thanx.
Thanks so much. Is the best video. Show real good. How a d. I did. My self. Mecanic guy charge me 800. And you are the best teach god bless you
Thank you so much for the video , god bless you , i fixed my car thanks to you about these information
If you plug in the electrical connector to the new actuator before installing, then turn the ignition switch to the on position, you can set the actuator post position by turning the dashboard cold hot switch position.
Thank brother 👍🙏
Great camera work
Great video
I did this yesterday on my 03 ford explorer damn it took me 3 hours to finished the job.
😂😂😂
You did it👏👏👏
Great video man I put one in my 99 model about a month ago it's kind of a pain but not to bad
Good video! Your video and your actions helped me a lot! Thank you very much for doing this
No problem!
By the way, i got my part, the right replacement part on amazon for 24.00. From premium parts wholesale. Chinese yes...but it works perfect
Thanks for sharing!
Thanx brother very nice and detailed video!
Part number 604-209 it fits perfect
Very good...It took me the same amount of time but man I got paid good ,Thanks
Worth the hassle!
I have a 2002 Sport Track. This video as well as many others on simular Ford models does me no good. Although many of the videos I've watched usually have the blend door actuator in the same location ( on the base board right of the steering column) and advise the removal of the center console for replacement. Mine is not in that location. And how do I know. I removed the center console! Yeah bummer! My mechanic said it was there as well as my shop manual I bought from Ford Administrative Department in Dearborn, Mi. At least that's where it claimed to have come from. Mine is located above the glove box. And it seems as if is an easy fix. But it is not! The front two 7mm are easy to access but the one in the back is very difficult. It appears it requires a special tool, little dexterous hands, or removal of the whole dashboard. So for those of you that may have a model slightly different, LOOK BEFORE YOU LEAP!!! And this includes if you are considering having it repaired y a mechanic. If you don't labor charges can be added based upon bad information.
The two different shafts are for a mid year design change, which Ford is famour for. There'e an early and a late model for the '02 Explorers and I believe the build date is March 3, 2002.
I would highly suggest you use the ford part replacement. I wouldn't want to have to do this job twice. I just did it.
Don't worry about the shaft it does fit in the hole.
I understood exactly what you were saying and after your video, it seems to be straight forward. But, I'm wondering how you managed to crawl under the dash like that. By feel I finally removed the two lowers screws and the electrical plug. And then, by feel again, I tried to put a 8mm socket (1/4" drive) onto the top screw. I'm still working on that one. In one way it's not a hard job, just hard to get at and at my age crawling under the dash is a task in of itself. I think I'll call me grandson for the one screw.
Thanks Mr.Cho! It works
Just curious, when you demonstrate at the beginning, turning heat dial to full heat, i noticed your "A/C" button light is on, Why would it be on? I have the 2005 explorer and no problem,so far, but usually when i turn cooler on i press the A/ C button, similar to your year/ model, and cold air is coming out after i press it on.
Good video
Thank You !
At first the ac button was on then after fix the ac button was deactivated haha good trick
make sure you blend door works easily back and forth or the cause is not the actuator but the door
Worthitness! 🤞🏽🔥
What would make your video so much better is if you're saying the name and the size of the tools that you're using
What about the actuator that switches from upper vents to lower? Is that similar?
After doing this it will come out the vents properly now,but if I turn to only defrost hardly any air comes out of the vents up on dash. Where I had opposite problem before as it only came out on dash. Any ideas.
This video looks very helpful. My heat and AC does not work it just blows air, would this be the actuator also?
Yes!
Isn't there also an actuator on the right hand side?
Mine does the same thing. I took my vehicle to a mechanic and they said there is 4 blend door actuator's and they have to spend five hours trying to figure out which one went out and 10 more hours fixing it sounds like bs
😂 you can pin point on a scanner with bi directional controls
i did take longer than you did but that was because i was frustrated on getting the actuator out. Now i was able to get the new one in and plug in the electronic connector all inside of an hour (i was pretty proud of myself that morning). Now i'm wondering if i put the actuator in incorrectly (common sense tells me that because of how the post is designed there was only way it could go in. i'm in doubt now because now my a/c doesn't work now and it worked just fine a few days ago and now all i'm getting is hot air no matter if i turn the dial to A/C or Heat. i looked at your video so i know you haven't had this problem. i don't want to put my console back together just to dismantle her again.
Hey sorry for replying so late. The groves on the actuator is such that there is only one way to put it in. If you put it in the the wrong orientation in wont push through. Hope you were able to pull it off.
Robert Wesley what did it end up being? I’m gonna say your blend door was broken, was that it?
Do we gotta drain anything before this this?? Singlr mom here and cannot afford to have my vehicle in the shop for 7hrs for them to get this done
No need to drain for ford explorer
Which you probably said it but what year explorer you have I have a 04 I'm thinking about trying to do is the process the same and yes it has that button up front on the center console everyone I contact to try and get fix saying I would have to drop the whole dashboard and can cost to 1000 dollars
02 ford
Omg ty so much I just got done putting the new actuator in was a little rough once to got to the actuator itself but it work let there be heat lol tx buddy definitely giving you a like and you just gain a new subscriber saved me 1000 dollars what the dealer and local mechanics was asking to do the job great job and video
Glad to hear you got it done!
In fact i replace mine without removing the console it'is a lost or Time but you need patience
why would you turn on heat with ac compressor on?
my car is 20 years old,I think I'll just cut out the console where it covers this part.
I can do it in less than 25min
Awesome