RadioMaster TX16S with HALL Sensor Gimbals - Binding to Volantex RC and Eachine Mini Warbirds
ฝัง
- เผยแพร่เมื่อ 5 มี.ค. 2021
- In this video in the series featuring the RadioMaster TX16S, I am demonstrating how to bind a Volantex RC Mini P-51D Mustang to the TX16S and set it up to have correct movements of the control surfaces and to assign one of the three-position switches to Channel 5 for the flight mode selection. This procedure works for all Volantex RC and Eachine Mini Warbirds.
As I continue adding my other models to this transmitter, I am going to continue making and uploading new videos to this series, so please stay tuned. Also, please let me know in the "Comments" if you would like me to cover any aspect or functionality of this transmitter.
Thank you for watching. Hope to see you back on our channel. Take care and stay healthy! - วิทยาศาสตร์และเทคโนโลยี
Very good.
When first setting up a new V761 model, you can change the channels during model creation, instead of correcting later. Rather than AETR the Volantex channel order is RETA.
So for ailerons, instead of accepting default of 1 you can change to 4. Then for rudder don't accept default of 4 but change it to 1.
I saw this in an Albert Kim video. 🙂
Very good video. Explanation is easy to understand and follow.
Well done video. All steps were clear and easy to understand. Thanks for the effort you put into this. I'm sure many will benefit from this video. Thanks.
Thank you this helped a lot
Great tips,mine was a little different,but video helped me work it out.P51 all ready for FPV as well with a proper Tx,cheers.
Thank you Jake, I am glad it was helpful. Good luck and have fun with your FPV setup. Cheers!
Jake:
Thanks for your comment about setting up for FPV. I have tried to do this with my Eachine P51D, but have had a devil of a time getting the CG right. Perhaps because I have crashed a lot testing this setup, my gyro does not seem to be working properly. The plane will fly straight and level okay initially, but as soon as I try to turn, it tip stalls and noses into the ground.
I mounted a simple microcam in the cockpit directly behind the canopy screen area, mounted onto a small chip of popsicle stick with hot glue, using an Eachine VTX03 for video transmitter, hot glued it to the canopy sides, and run the antenna under the canopy, and out through the seam behind the canopy. The battery cable was connected to the battery which sites in a slot cut in the foam between the tail and the canopy. Choosing a small, but not too small battery (or too big) has been a challenge for center of gravity setting. My P51D started out significantly nose heavy, making the addition of FPV gear further back less of a problem. I used a piece of clear molded plastic from a merchandise display pack to the fuselage of the plane, enabling the reading of the channel & band LED lights easy before, during, & after flight.
So how did you do yours?
Thanks. -Jim
@@jamesceastep8874 I'm using a VC400. AIO cam powered off the flight battery, it's mounted best the front of the canopy on the CG balance point. It's flies well, and doesn't affect flight time much.
Thanks. I have a Mini Wing Dragon and was able to get it working using the MT9XX mode. Selecting the Dragon submode enabled the telemetry. Use channel 5 on a 3 position switch to set the flight mode. Maybe this will work for other models as well.
Awesome vid!
Thanks for this explanation.
1 question though. Is it possible to assign the "stunt" button to the tx16s? If so please do a little vid explaining how.
Hello! Great tutorial, it helped me a lot! one question, is there any way to assign a switch for the return home? Thanks!
Thanks for the vid - have you bound a Volantex Ranger 400 to your radio? I tried v761, the plane responded to the bind ... but NONE of the controls work. Multiple tries, also cycling power, nothing. Any suggestions?
Most of my planes 99% are now bound with my Radiomaster TX16S for higher resolution and convenience. Most of the time I duplicate from existing models and just change receiver type and minor adjustments, since I have so many customs inputs and mixes i copy across many planes.
I try to keep it very basic for all my planes. No exponential, just dual rates (or triple rates for aerobatic or fast airplanes). I am planning to program some elevator mixing for my planes with flaps, but that will be it. I try to fly my planes as manual as possible... just a preference I guess. How many planes do you have by now?
Very cool. Does using the Tx16s increase the range of the plane significantly? I want to use an fpv camera but am afraid to fly it out of range. Thank you.
Can you show how to use special functions to mix in full manual (expert mode) with 100% aileron so one can do aerobatic rolls?
how to bind tx16s to the XK a180 and the expert mode switch, I can't mod the expert mode on the tx16s . please help me !
Hello sir. I just wanna ask how to bind my XK A210 mini Trojan to my radiomaster and what protocol should I choose in internal RF module?
Thanks
Hi, I managed to do everything as what you have shared. The flying mode seems working fine. However, on acro mode, the moment the throttle is on, the gyro is also on automatically and I am not able to fly in acro mode. How to overcome ya?
I have a Spitfire and a bf109 that I've setup iny tx16s. On the Spitfire, I get a delay on every input. Is this something you've experienced? Bf109 is fine, it reacts immediately to any input.
Thank you for this video. I was wondering if the current TX 16s can do this?
Hi Gordon. Yes, all OpenTX transmitters can be easily paired with this airplane.
Can you also use edge tx
please show how to program aerobatic button for the beginner that is getting this radio, thank you
You description was excellent. Thank you!
Does anyone know if the C2500 chip from the 4 in 1 module is the one that runns the V761 control code? I only have the C2500 chip in my Radiomaster TX12, so this is important to me. - Jim
NRF24L01
Same procedure for radiomaster boxer with 4-1 protocol ?cheers
Thanks.
How would you set up the aeronautics switch especially as it is a button and not a switch?
Also how did you find out the name of the protocol as it is not mentioned in the manual?
Here's a video which explains how to setup the stunt/actobatics switch: th-cam.com/video/qRjItWkhFEM/w-d-xo.html
I have XK A290 F16 and a XK A100 SU-27. How do I bind them to my Tx16s?
Informative video, thanks. I would like to setup a switch as a throttle disable switch so when I am setting up my plane I don't have to worry about the prop spinning. Is there a way to do this?
Yes, go to special funktions in your opentx radio and then create a new function, assign a switch and choose the function "override" , then select your throttle channel and set the value to -100. At the end make sure to check the checkbox and you have a throttle cut
@@maxmeister6355 Thanks..
Do volantex have s-fhss protocol ?
hi Props & Wheels, this is amazing video accurate and simple, do you know the channel for the Aerobatics switch?
Hi Alberto. Thank you so much. I am glad you its it. I am planning to make a video showing how to program the aerobatics switch soon. Stay tuned!
@@PropsWheels Hi. Did You make video showing how to program the aerobatics switch, please? I can not find it on Your channel...
Why would I need to rebind when the radio is power cycled?
Hello Friend. I have a question. Will this radio / transmitters also connect to the slightly larger version of the p51 750 768-1?
Nope. And the hardware in that unit means it cannot be hacked for the Multi Module radios.
I have the ME-109 from Volantex and am trying to bind my DX6e to it and I cannot get it to work. Any suggestions?
Spekrum has it's proprietary software install on their radios. You will need a radio that supports Open TX software to work with these planes.
this is very helpful thank you.
i only have 1 Volantex plane (sportcub 500) and dont have any eachine planes. each time i turn on my TX16S, it seems to have "forgotten" the volantex receiver and i have to bind it again.
can you help me?
thanks
Did you try turning on the TX16S first and then connecting the battery to the planes within 2-3 seconds? Please try this and let me know. Thank you.
Have you had any luck w tx16s remembering volantex, eachine reciever?
@@PropsWheels .I tried it both ways, powering the TX 1st and then powering the plane 1st. Sadly, both ways didnt help
Am i able to bind a spektrum DX4e to my p51?
No
my screen looks different for switching channels direction
Can you help me bind it to the original radio control, and that is because I Lost the original Airplane that comes with the Radio, and I did buy the versión of without radio, because I all ready have one
The bind instructions are in the manual but I think it said turn on the tx, plug in the battery within 5 seconds and it will auto bind.
Well first is the battery of the aircraft, and then your transmiter
Thank you for this very useful video.if you could give my some advice since I have not been able to make link with the steps that you show. the only thing different is that my radio is mode 1out de box an de plane is in mode 2 thank you so much
Right aileron should go up not down looking from rear of
Plane.
Does it his work with spectrum DX 6e radio? Can anybody help me into this next phase of flying with hobby grade tx & Rx.
Just tried this on my tx16 and it hasn’t worked. The receiver binds but then won’t respond. After much research, the only solution is to bind to the receiver and then turn on the range test button to reduce the power of the transmitter. Unfortunately that shuts down access to any other screens.
Advice on how to overcome this problem would be appreciated.
Hi.. Same issue with mine.. Range test also low power mode, we can control.. After exit range test or low power mode.. Everything gone.. So sad..
did you figured out Im still dealing with the same issue< i thought an update will fixed and no same bs
It doest bind to my tx16s no matter what I try
Hi Michael. Is it the same version as mine? Sometimes manufacturers switch to another protocol over time on the same model. Is your new or did you purchase it a while back? Probably this is a stupid question, but I should still ask: did you follow all steps I outlined in this video in the correct order?
I've got mine a few days ago and binding it sort of worked. I saw the red light inside the fuselage stoped blinking which normally indicates that the binding process was successful. But the controls didn't work. Then I accidentally entered the range option which reduces the output power and the controls suddenly moved. So I have to turn on low power mode permanently to make it work. I haven't had a chance to fly it yet and see if the range is good enough on low power mode. I remember seeing in a different tutorial video that some toy grade models require this mode to function properly
@@Earlboone thanks bro, just I needed, I guess all this changed with newest firmware...
@@Earlboone Yea I discovered this also with the BF 109. Binds just fine with my X9D+ set up for V761 but I had to select reduced power for it to work with my new TX16S.
This screen looks nothing like my screen, this video does not work with my brand new controller, I am so tired of this hobby, it was much more fun 25 yrs ago, this electric shit is ridiculous