ฝัง
- เผยแพร่เมื่อ 27 ส.ค. 2024
- Blower Motor Resistor for Nissan Versa 2007-2011 Tiida 2007-2009 Cube 2009-2010
amzn.to/2MCalyu (Amazon Affiliate)
Nissan Versa HVAC/HEATER Blower Motor 2007-2011
amzn.to/2MAaVMZ (Amazon Affiliate)
In this video, I will show the location of the blower motor resistor. Also, know as VBC Variable Blower Control Module on my 2009 Nissan Versa the Nissan Cube has the resistor in the same location. MY CHOICE / NOW, WHAT'S YOURS? Please Subscribe, like and share my Videos.
Blower Motor Resistor for Nissan Versa 2007-2011 Tiida 2007-2009 Cube 2009-2010
amzn.to/2MCalyu (Amazon Affiliate)
Nissan Versa HVAC/HEATER Blower Motor 2007-2011
amzn.to/2MAaVMZ (Amazon Affiliate)
For anyone that has a 2010 Nissan Cube and needs their blower motor resistor replaced, book time is just about 6 hours. The actual blower motor itself pays less than 1.
I am doing both tomorrow on a customers vehicle. Neat
I need it.
I was getting ready to change my blower , click on this as " runs only at #4 setting " . Now i do this first . ( will change blower as well , wonky from day one 2010 Cube) like & subscribe .
Good video! Very helpful. Magnetize the screwdriver bits to hold the screws on.
Our 2008 Versa SL blower has finally given up even the 4th setting, and it's friggin cold out. I have snaky arms so this might be my plan. I have already heard from the mechanic how he will approach the fix. I am going to try to avoid the labour cost of taking apart the dash. Other than the dealer breaking my clockspring mech and refusing responsibility, it has been a pretty good little car. The horn doesn't work, and the wipers are 'very' intermittent', and she still has the factory sparkplugs because the manifold is stuck so she is hard to start sometimes. That's it. Oh, the dealer did replace the transmission in the 9th year of the 10 year warranty, which is the only reason she still goes at all.
How do you know if it is the blower motor or the resistor
Just had to do this. Found the part on eBay for $15 with free shipping (from US, received inside of 4 days). For the bottom screw I wound up using an offset screwdriver from Advance Auto for $4, for the top screw I was able to use a precision screw driver and remove it relatively easily.putting the top screw back in was a bit of a pain, I wound up using an extending magnet to help position the screw and put it back in. My understanding of Nissan's HVAC is that position 4 is the blower motor only, bypassing the Resistor, so if position 1-3 is not working this would be the issue, if all aren't working it's probably the HVAC Temperature control unit, which is about $60 used (ebay) and takes about 90 minutes to 2 hours, or your blower motor, which can be removed in about 10 minutes.
Oliver, thank you for the information. That's good stuff.
Спасибо что вы так усердно пытались все показать
Thanks for sharing! What year is this versa??
I just ordered the part from aliexpress for 12$, I'll let you know it it works in 37 to 39 days :)
Jansim Blank ok please do.
Well?
and?
@@robmendoza6210 ah ha! Forgot about that. It worked!
@@Gvaz Yeah it worked!
Had this happen to me this past week and was worried I was going to have to disassemble the entire console to get this damn thing out. Glad to know that with some finesse, it can be done. Thanks!
Its a little tight up there, but it is due-able.
Is Blower motor resistor and Heater fan resistor same?
Can't even get to mine in the 2009 Cube. Tried from the top behind the instrument panel (put a hole in the dash behind the cluster, tried from underneatheth, but even the tiniest tool I have cannot get into the stop. When I was able to touch it, I cannot even unlock and remove the clip.an
I just did my 09 cube and had to tear the dash apart and go through a hole in the dash behind the little square storage hole to the left of the AC controls. I had to use a LONG Phillips screwdriver and a long set of forceps. The screwdriver was 22 inches, but that was a bit too long. 12 to 15 inched would have been better The forceps were 12 inches long too. They really helped to get the new resistor in place.
@David French It is a ways in behind things which is why you need the long screwdriver and forceps. I had a hell of a time finding it. I know it's not easy, but you may need to get your head under the dash with a flashlight so you can gauge where it is an to get an idea of what you are looking for. Trust me though, it is there, and the long screw driver and forceps helped A LOT... If you can post me a picture from the front of your dash looking in I might be able to point it out for you.
@David French I just sent you a couple emails.
Would someone be able to help walk me through this for my 09 Nissan cube ? I can not find it at all have been at this for hours now
@@mrs.rosewilkins358 Did you read my comment earlier in this thread? If so, do you have your dash apart? If you have your dash apart, can you post some pics of the inside of your dash? Maybe I can point out where it is or where you need to look for it.
This project took almost 3 hours... I could not lay upside down, so I pulled the seat, and the all of the braces in front... and still had trouble reach that little connector... but, with lots of cursing and luck, it's done... you should show all of the hard parts and not just the money shot... lol
I know this video is old, but you need to remove Cube from your description. The Cube requires you to take most of the dash apart, the resistor is placed parallel to the front of the car behind a round welded structural tube. I'm still working on getting the rest of the dash apart.
Could you possibly help me locate it? I have a 2009 nissan cube and purchased a new resister already but cant locate it for the life of me! Thanks for your time! 🙏🏽
@@sethcalhoun123 I will have to take the dash apart and shoot a short vid for you this weekend.
I can't get to mine with even that. Super tight. Im. Thinking maybe a ratchet wrench w that bit thru it. Geez...
Thanks man. Does this work for the 2019 model?
If your attempting this on a 2010 cube it’s a lot more difficult then it looks. Although putting the new one in is easier than taking the old one out.
My 2010 Cube is standard transmission . Can you tell me if my blower resistor is in same location as vid. ,if not where . I took a quick look ,not sure I found it . #4 setting works as described . I know one thing , i get into this i will be taping up my wrist's & forearms . Sharp edges under there , already scraped up . Thank ahead of time Frank . Murphy .
Thanks man.
I'm too fat so it will be more work for me:)
Since it is winter and raining, the job of getting those damn screws out proved too challenging for the day. I did however unclip the original, clip it to the replacement and verified it is working. Is there any issue if I just use a blank screw hole and fasten the replacement to an unused space under the dash (making sure it doesn't touch anything else under there), and just leave the broken original as is? Or does the original's slot it fits in use the fan as active cooling for the resistor?
@Rcjr I'd like to know this as well
Yes, that works. No need to put the package back into the holder. I verified this yesterday on my 2011 Versa.
Damn, I am just trying to unplug that damn clip! lol
Thanks for that....thing is my fan is still blowing underneath by feet....just not on top near face. Must be two blowers?
What would the problem be my Nissan Versa sedan 2015 the blower makes a roaring noise when it gets up to a higher settings
On the 2015 they moved the resistor.
My versa a/c light is on with fan off. When the fan is turned on to 1,2,3, or 4. The ac light and compressor kicks off. Any idea's?? Resistor or climate controller??
does the dashboard have to be taken off or is that a way of working around it?
Not gonna lie you have to be creative with your tools and very patient. Its very tight up there but it is due-able. Go to this link scroll all the way down www.nissanversaforums.com/general-versa-discussion/2401-interior-blower-vents-etc-not-working-3.html Look at the tool he used. Look at the tools I used. Push The driver seat all the way back lay it all the way down to the back seats and you or whomever will have to maneuver under there. Good Luck.
cool, thanks so much
Rc Jr , is the blower resistor in same place on 2010 Cube standard shift ? .
Do you know where is starter relay for Versa.
anybody knows how i can get the dash out in a 2014 sedan(2gen) to replace the blower fan for the
A/C????
You paired 89 dollars for the resistor??? In Montreal it should be more expensive and I got it for 60+ tax at NAPA Auto parts. On the net they sell it for ~75 dollars. Nissan here they sell their part 195+tax. So it less then third of the price I paired.
wat size socket wrench is that trying to take one off now
phillips head
Hey brother. What if my blower motor only blows on 1 and 2? My Nissan Versa 2011 won't blow on 3 or 4. I'm stumped. Any advice? Thanks.
Watch my video. It will answer your question in detail.
A/C Blower Fan Stopped Working Nissan 4 Step Easy Check
th-cam.com/video/vyeNcG4rtcI/w-d-xo.html
Rc Jr I watched the entire video, but you don't explain or mention how to troubleshoot the AC if it only blows on 1 and 2.
i have the same problem with my 09 versa did you ever figure out what was wrong with it ?
My a.c. went out it was making noise before and just stoped working
watch my video on the blower motor. sounds like that maybe the problem. not sure though. turn on a/c and tap on the blower motor. if it starts running it is going bad.
My little ratchet still to long. I see with what you took it off and don’t understand how you managed to unscrew them. All Versa are the same though.
Same thing on my cube. Less than 1 1/4 inch between the safety bar and the screw.
Damn thing is under drivers side dash. Had to take tons of crap off. Stupid location hard to locate.
Bro help