Hey, Klowny, I used your' idea yesterday after seeing your vid. I completely emptied an almost empty paint can and drilled a hole .213, #3 drill about 3" from the top. Flushed it through the drilled hole with Mineral spirits to clean out excess paint. I stuck a tire valve in the hole and soldered it with a soldering iron. Don't have to worry about flame that way. Put a little more spirits to clean nozzle. Put 90 lbs. air in through tire air fitting on the side. it is easier than trying to charge through top nozzle. I had an air gage I mounted on a tire nozzle for my lawnmower. It told me exact pressure. That way I don't lose any pressure while checking. Works great with water will try spraying paint tomorrow. I like my new refillable paint sprayer. Thanks.
thanks for the video. I know people be dissing this whole thing saying its too costly and all. all i gotta say is, some of us are smart enough to actually have the items needed around as is. This method should allow me to save the contents of more than 40 or so cans of spray paint that were effected by changing temperatures, and are rather full. I have a tire valve stem sitting around, and a compressor, so not only do i not need to buy anything, im also going to keep a good amount of more waste being created, and use the paint that has been made rather than another can going to the recycling full of paint, a wasted product.
you can also use a rubber tip air nozzle right on the plastic can tip to re-fill it with air and get the last of the oil out, old school shop trick, but for re-filling, that's awesome I will have to try that!
Thanks for that tutorial! I had a few cans of WD40 with no air in them but half full of lube. They are all topped up and work great! Again thanks so much I had no idea you could do that! A+
wd 40 is known for that i have some wd40 cans around half full of fluid but no air. I don’t think i am going to buy wd40 again if they are going to do that.
Good info, thanks for sharing. A simple method I use to re-pressurize a can is simply (well first protect your face arms and hands) pull the top off, set compressor so you don't blow it up, take a rubber tip air gun apply air and depress top at the same time. Then you have the pressure to empty the lubricant or whatever was in it.
That's great! I didn't know it was possible. One caution though. When I was young I drove a garbage truck over the summer holidays and we used to pour gasoline on the piles of garbage at the dump and light them. At some point the aerosol cans would start to pop and I can confirm they're like BOMBS when they go off!!! So I'd go on the light side of the pressure you use if you do this.
LOLOL well that's the first time i've ever had anyone say that to me, it's kinda a compliment since it's my wish to be atleast my average height's weight
yes over pressure can be dangerous, we cannot fill em up full pressure, can must be rust free as well, but if we don't get too greedy with max pressure, things should be ok
great tip. here's one from a lazy old man... the tire valves come 2 to a pack. remove the Schrader valve, throw away. Now you have one for filling, one for adding the compressed air. :)
if you take a five foot section three-quarter inch inner diameter air hose put a male quick disconnect on one end with your air Chuck on the other end you can put your fluid inside that 5 foot section and go directly through the valve stem saving a lot of time and effort you are very welcome
+Ricky Mcgrath use a clean designated section of Hose only for that purpose the hose is your Reservoir if you use a 5 foot section of hose you should have roughly 5 to 6 ounces or more of oil
+DeeJayMontevideo use a dedicated section of Hose the hose is your Reservoir put the fluid in the hose then attach it to the can it will go in directly
I love it. I have been in the automotive industry for many years and I love it when someone can find a way to modify something like that. I call it afro engineering.
The only thing is how do you get the paint into the can in the first place. And how much paint to how much air / how do you know right amounts even if you could fill a can up? Really cool video may give it a try to see how pro quality it comes out. Because getting tons of match paint in spray can form is difficult.
I use a large deodorant can that I completely removed the scent from. This can is used for storing extra butane from waste bottles of butane. Basically I heat up the nearly empty or "empty" butane can, and freeze the deodorant can. By using an adapter found in the cap is a butane can, I can transfer the gas without losing any.
If you don't have an air compressor... (which most people don't have) You can fill it back up with compressed air by just going to a gas station that has an air hose for tires and use their hose to charge the can up. You'll have to check the air pressure to make sure you don't overcharge it of course but it beats buying an air compressor to save a few pennies on a spray can.
Yes: In fact I have one. Only the cost of buying a tire valve and a Schrader valve tool: you could re-use any spray can and fill them up with anything you want: But how many times does anyone use a spray can? I don't need this crap. You must be really lonely to troll something as trivial as this.
Lots of guys have lots of spare time. It's good that they use their spare time doing such trivial things 'stead of listening to the whisper of the devil. Look around you and see how the young men destroying the world. That's because they never heard the proverb - "An idle brain is Devil's workshop"
What did I say to attract such expletives? Please cool down and try to understand me. I just said that this guy is using his spare time to do small things which may or may not influence your life. At least he is not going the way young men of Syria, Afghanistan or Pakistan are going.
I tried this with adding purple power to a former break cleaner can and I couldn't get it to fill. Why? Air wanted (but couldn't) to come out of the small plastic tube as the fluid tried to go in. I had to pull a vacuum on the can, then dip the tip in Purple power and let it suck in the fluid. it took 4 times to get the can to the 70% full. Pressurizing worked just as easy as you show. Next, I have a 1/3 full spray paint can that's lost its pressure over the years but the color matches something I've used before, so this is perfect and easy for that.
Once he said my own personal favorite lubricant the entire video seemed to be much funnier. The shitta valve, the squirter, insert in the hole, see how well it sprays, lube it, and the shoe's killed me.
Yeah and "you can just put your little tool in it" 😂 you know so you can fill that "bad boy" .... Up ???? ... Wait a sec there dude I don't swing that way. So now my question is where do I get a female can? Sorry I wasn't prepared for this I wasn't expecting all this sex stuff to be going down. I didn't know this was for personal lubricant let alone the in a boy subject part. Sorry I think I'm ..... Nope this is definitely youtube not youporn hmm I didn't know this was a thing being taught on youtube and I must say this is appalling 🤨 you can just take your squeeky shoes and gtfoh you damn perv...... 😏 You know you want to haha 😜🤪😂 well that amused myself lol thanks for the video and the laugh and on a serious note thanks for the lesson I didn't know you could also refill the fluid along with the re-airing. I guess I will subscribe thanks again.
Brake cleaner always loses all its propellant sitting on the shelf. My cans have the reverse valve with the male tip on the spray nozzle. Even so, how would that tire valve be able to depress the can valve to allow this to work? Osmosis mebbe.
Be aware that the chemistry could be a problem. Some materials do not behave well under pressure with air. What your example is seems to be OK but not all. Example: Methane under pressure with air...explodes.
Done under careful condition with control it is normally not a problem but consider that plain air is almost never used as an aerosol propellant because it might be so dangerous. I would have researched the chemical interactions first and then used a normally non-reactive gas such as refrigerant.
Wow, you just saved me a ton. One of my grandkids held 2 new cans of WD-40 upside down to blow balloons up... I thought I'd be going to prison for murder, but now I'll be laughing at them while I show them I know more than they thought I did. Okay, I really don't, but that'll be our secret, okay? Now off to walmart to get a couple of those tire valves. Too bad my compressor only goes up to 80lbs... But, I can always refill the cans, can't I... Cool tip. Subscription coming because, I know I want to.
Nice shoes Klowny. The gas normally in the can is more compressible than air, so this won't last as long as the original fill. But air'll work in a pinch.
Only one suggestion and that is to insure that you do not overfill the can with compressed air or you will have a heck of a bomb going off in your hand. I would suggest a regulated air supply limited to 80 - 90 lbs of pressure at most. Plus as with a tire it would be much better if you had it in a container to shild you from the can should it might burst. Glove would be a help and wear safety glasses when doing somethig like ths.
gloves & safety glasses are for wimps..... that is what youtube is for. lets see if it works... HAHAHA.. messing with ya, true could make a person have a bad "few MONTHS"...... (see how I did not put days, it could be REAL BAD!)
Have a friend who did this after he saw the video. but he cheated he made a "Blast cage our of a piece of steel with a cap welded on top to prevent shaprnal from moving it it blew. Haven't seenit but he is an old military type and used to work EOD, still has all his body parts. LOL
When you fill the bottle with a liquid, place some fitings around the male threads of the valve in order to get a bigger hole ( inversed reducers). Filling will be easier...
I'm going to try this. One problem I have is that my spray paint cans seen to get stopped up somewhere in the line that runs from the bottom of the can up to the spray tip.
I am wondering about a similar thing. I am wondering how the companies can put paint cans in spray can form. Like if i got to a local hardware store or paint store get a paint matched in a paint can form. Is there a simple way with an air compressor i could take an empty aerosol can and fill it up with paint and compressed air to make my own spray can bottles? Because it sucks buying all these spray can bottles if i can wash out clean and reuses with other paints to make all different color aerosol spray cans from scratch. Because some time its hard to get a paint match in spray can form. I could uses a method similar to this to convert from can form to aerosol can form
you can do this with butane lighter gas, it is much more effective, as the air will soon become depleted. I firstly charge the aerosol with the liquid to be sprayed, then chill it in the freezer in preparation for charging with butane propellant. chilling the aerosol allows a full charge of butane propellant to be put in.
Hi..i watched you recharge that airsal can with that lubricant..and that was great.. and know ,..id like to ask you how do I recharge my can of propellant, for airbrushing..can you show me how buddy..my name is Emmett..and I'll be waiting on your response...thanks..
kudos for the clown shoes, but I hope your not clowning around showing us this tip. If you aren't then kudos for the amazing tip also. Something I would have never thought of. You can bet I'm trying this one out!
You could solder the copper part of the valve into the can. Make sure the valve of the can itself doesn't get to hot. There are other videos which show how to do that.
![เปิด อาณาจักร หมื่นล้าน "สาระตั้ม" l [Nickynachat]](http://i.ytimg.com/vi/3XE0nPF4YkQ/mqdefault.jpg)
![[LIVE] : ONE ลุมพินี 87 วันนี้!! คู่เอก "ก้องชัย vs โชคปรีชา"](http://i.ytimg.com/vi/YN6e7HVnekw/mqdefault.jpg)
This is the easiest method yet. I prefer super easy for the occasional recharge/refill of a can. Thanks for sharing!
Thanks for watching
these how to videos rarely impress me,you have impressed me greatly,i wish i knew this 30 years ago
thank u sir. that means alot
nice that you reuse things instead of trashing a perfectly good can. Good for you!
Hey, Klowny,
I used your' idea yesterday after seeing your vid. I completely emptied an almost empty paint can and drilled a hole .213, #3 drill about 3" from the top. Flushed it through the drilled hole with Mineral spirits to clean out excess paint. I stuck a tire valve in the hole and soldered it with a soldering iron. Don't have to worry about flame that way. Put a little more spirits to clean nozzle. Put 90 lbs. air in through tire air fitting on the side. it is easier than trying to charge through top nozzle. I had an air gage I mounted on a tire nozzle for my lawnmower. It told me exact pressure. That way I don't lose any pressure while checking. Works great with water will try spraying paint tomorrow. I like my new refillable paint sprayer. Thanks.
Toolman Awesome ..thanks for watching!
Well done mate, this is the best one I've ever seen on refills on cans and I have seen all of them. ThaNK YHOU VERY MUCH.
Thank you
thanks for the video. I know people be dissing this whole thing saying its too costly and all. all i gotta say is, some of us are smart enough to actually have the items needed around as is. This method should allow me to save the contents of more than 40 or so cans of spray paint that were effected by changing temperatures, and are rather full. I have a tire valve stem sitting around, and a compressor, so not only do i not need to buy anything, im also going to keep a good amount of more waste being created, and use the paint that has been made rather than another can going to the recycling full of paint, a wasted product.
you can also use a rubber tip air nozzle right on the plastic can tip to re-fill it with air and get the last of the oil out, old school shop trick, but for re-filling, that's awesome I will have to try that!
Thanks for that tutorial! I had a few cans of WD40 with no air in them but half full of lube. They are all topped up and work great! Again thanks so much I had no idea you could do that! A+
wd 40 is known for that i have some wd40 cans around half full of fluid but no air. I don’t think i am going to buy wd40 again if they are going to do that.
Does any one see those ronald mcdonald shoes at 6:36
That's because he's "Klowny: The only klown in the world that can show you how to work on cars!"
karl webber just killed the video because of that
*saved
Yep haha
Hahaha
Good info, thanks for sharing. A simple method I use to re-pressurize a can is simply (well first protect your face arms and hands) pull the top off, set compressor so you don't blow it up, take a rubber tip air gun apply air and depress top at the same time. Then you have the pressure to empty the lubricant or whatever was in it.
That's great! I didn't know it was possible.
One caution though. When I was young I drove a garbage truck over the summer holidays and we used to pour gasoline on the piles of garbage at the dump and light them. At some point the aerosol cans would start to pop and I can confirm they're like BOMBS when they go off!!!
So I'd go on the light side of the pressure you use if you do this.
Great job I was thinking of doing something professionally refill paint spray its amazing I would try this method to put my own paint color in it .
Holy Shit I never thought Ronald McDonald would ever teach me anything!
Apart from being fat?
LOLOL well that's the first time i've ever had anyone say that to me, it's kinda a compliment since it's my wish to be atleast my average height's weight
wonderful video millions of these can are ending up in the thrash when they can be reused and recycled
yes over pressure can be dangerous, we cannot fill em up full pressure, can must be rust free as well, but if we don't get too greedy with max pressure, things should be ok
Hey, did you get it to work? The fluid won’t go in can for me.. it just stays in valve and won’t budge.. What am I doing wrong?
Follow me on fb. Search for Save an Aerosol
great tip. here's one from a lazy old man... the tire valves come 2 to a pack. remove the Schrader valve, throw away. Now you have one for filling, one for adding the compressed air. :)
lol thanks!
Fantastik! Love the order and cleanliness of your shop too:)
thanks for watching and commenting
by far the best refill solution I've seen !! thank you 😊
i like how you talk, cracking me up 😌
Thanks! Don't forget to subscribe
Definitely good tip. I threw away an old WD-40 can because it ran out of air but still had fluid in it
Thank u sir!
if you take a five foot section three-quarter inch inner diameter air hose put a male quick disconnect on one end with your air Chuck on the other end you can put your fluid inside that 5 foot section and go directly through the valve stem saving a lot of time and effort you are very welcome
Definitely not recommended. You risk contaminating your air hoses, tank and potentially your tools.
+Ricky Mcgrath use a clean designated section of Hose only for that purpose the hose is your Reservoir if you use a 5 foot section of hose you should have roughly 5 to 6 ounces or more of oil
+DeeJayMontevideo use a dedicated section of Hose the hose is your Reservoir put the fluid in the hose then attach it to the can it will go in directly
Why not just fill your air hose with your fluid of choice??lmmfao work smarter not harder!
@@rickymcgrath2314 it keeps it all lubed up hahaha. Plus if you use mineral oil like me it's good for your rubber hoses
I knew I shouldn't have thrown away all those flat spray paint cans...😭..this was great, I learned something new today...
lol that sux..thanks for watching
Quite possibly one of the most helpful videos I've ever watched. You are awesome.
Thanks for watching
I agree
gamer taboo kkvery
gamer taboo
very useful nice
I love it. I have been in the automotive industry for many years and I love it when someone can find a way to modify something like that. I call it afro engineering.
The only thing is how do you get the paint into the can in the first place. And how much paint to how much air / how do you know right amounts even if you could fill a can up? Really cool video may give it a try to see how pro quality it comes out. Because getting tons of match paint in spray can form is difficult.
Awesome, I was about to put a hole on some of my WD40. Thanks.
lol thanks for watching
Sometimes even clowns have great advice. Thanks! I used it on a very expensive $30 auto base coat can that lost pressure.
i first thought what an asshole!! then i saw the clown shoes i lmfao
I use a large deodorant can that I completely removed the scent from.
This can is used for storing extra butane from waste bottles of butane.
Basically I heat up the nearly empty or "empty" butane can, and freeze the deodorant can.
By using an adapter found in the cap is a butane can, I can transfer the gas without losing any.
That is pure genius, I never knew that was possible. Thanks!
thanks for watching
Sure thing. I'll hafta watch more of your videos when I get more time, I like your style.
If you don't have an air compressor... (which most people don't have) You can fill it back up with compressed air by just going to a gas station that has an air hose for tires and use their hose to charge the can up. You'll have to check the air pressure to make sure you don't overcharge it of course but it beats buying an air compressor to save a few pennies on a spray can.
or a bicycle pump
Yes: In fact I have one. Only the cost of buying a tire valve and a Schrader valve tool: you could re-use any spray can and fill them up with anything you want: But how many times does anyone use a spray can?
I don't need this crap.
You must be really lonely to troll something as trivial as this.
Lots of guys have lots of spare time. It's good that they use their spare time doing such trivial things 'stead of listening to the whisper of the devil. Look around you and see how the young men destroying the world. That's because they never heard the proverb - "An idle brain is Devil's workshop"
What did I say to attract such expletives? Please cool down and try to understand me. I just said that this guy is using his spare time to do small things which may or may not influence your life. At least he is not going the way young men of Syria, Afghanistan or Pakistan are going.
STICK YOUR STUPID SHIT FILLED BRAINLESS IRRATIONAL BULLSHIT BACK UP YOUR SHIT FILLED IRRATIONAL BULLSHIT BRAIN WHERE IT CAME FROM
great job , trying to help others, the shoe did for me . 10 million thumbs up ,
thank u sir! dont forget to subscribe :)
Thumbs up for the shoes !!
thank u kind sir
them shoes at the end tho lol
thanks for the help klowny!
+Jack Johnson thanks for watching
Very cool. I hadn't realized these could be refilled.
Yep..thnx for watching
from the looks of your work bench yr prob abit of a perfectionist, nice video on how to save a can .....
lol thanks for watching
I tried this with adding purple power to a former break cleaner can and I couldn't get it to fill. Why? Air wanted (but couldn't) to come out of the small plastic tube as the fluid tried to go in. I had to pull a vacuum on the can, then dip the tip in Purple power and let it suck in the fluid. it took 4 times to get the can to the 70% full. Pressurizing worked just as easy as you show. Next, I have a 1/3 full spray paint can that's lost its pressure over the years but the color matches something I've used before, so this is perfect and easy for that.
Hey Nice shoes, My dad had a pair back in the 20s. no one messed with him.. Sweet.
Yeah baby
Brilliant brother!!! Nicely done. I like your accent too. I'm sure the women dig it.
lol
This guy works smarter, not harder. All of the other videos show people drilling holes into the can and putting on a tire valve. smh
That's awesome. So much better than the method where they cut a hole in the bottom and jb weld the valve in.
Great Video. I will try this magic trick on my tools. Thanks for posting.
Awesome thanks for watching
6:40 Now you have your personal lubricant in aerosol form! What could be better! The possibilities are endless.
finally somebody that understands me!!!!
Thanks👍 I️ have a full bottle of shave cream that I️ thought was a lost cause. I️’m going to try this on it soon.
Great video content, love the ronal mcd shoes!
Thank you!!
Salamat(Tagalog)= thank you for sharing tips.
Thank you for watching and don't forget to subscribe
0:32 his favorite personal lubricant
wòooooooo babeeee
lol ,I caught that one too.
fer maximum _Penetration_ according to bottle
- up to the hilt
Sure it is! Thanks a lot from Panama; such a good idea. Kudos!!!
thanks for watching
Once he said my own personal favorite lubricant the entire video seemed to be much funnier. The shitta valve, the squirter, insert in the hole, see how well it sprays, lube it, and the shoe's killed me.
Klowny comes thru with another dope idea! Thx man!
Lol thanks for watching
just love the shoes ,class .
I did this last weekend and my girlfriend got pregneat
Daniel 1999 YES!!!
8764
you can't spell it but you can make it happen and that's what counts!
That's bcus while you were fckn with the can, somebody was fckn her you idiot!
OH MY GOD I AM CACKLING, PREGNEAT. WHAT IS A PREGNEAT.
Nice shoes
thank u kind sir
actually ...i like your shoe :)
nice shiny shoes! suddenly, i need a pair that i can wear to work!
they are very comfortable..i highly recommend them
MAN! NICE SHOES!!! Thanks for the video.
Wow Klowny That's amazin'! I've never thought that to be possible. COOL!
thanks for watching and commenting
"This is my favorite personal lubricant, penetrating oil"... Sorry man but that was funny. Great vid tho, thanks for posting!
Yeah and "you can just put your little tool in it" 😂 you know so you can fill that "bad boy" .... Up ???? ... Wait a sec there dude I don't swing that way. So now my question is where do I get a female can? Sorry I wasn't prepared for this I wasn't expecting all this sex stuff to be going down. I didn't know this was for personal lubricant let alone the in a boy subject part. Sorry I think I'm ..... Nope this is definitely youtube not youporn hmm I didn't know this was a thing being taught on youtube and I must say this is appalling 🤨 you can just take your squeeky shoes and gtfoh you damn perv...... 😏 You know you want to haha 😜🤪😂 well that amused myself lol thanks for the video and the laugh and on a serious note thanks for the lesson I didn't know you could also refill the fluid along with the re-airing. I guess I will subscribe thanks again.
i just seen your klown shoes love it dude you histerical im all subbed up brother !!
Brake cleaner always loses all its propellant sitting on the shelf. My cans have the reverse valve with the male tip on the spray nozzle. Even so, how would that tire valve be able to depress the can valve to allow this to work? Osmosis mebbe.
fun facts... does Ronald McDonald know you stole his shoes?
Was thinking the same thing lol
HAHA I made a similar comment, about the shoes ...
My method is so simple. And the pressurizing part, even easier. Mess free
Be aware that the chemistry could be a problem. Some materials do not behave well under pressure with air. What your example is seems to be OK but not all. Example: Methane under pressure with air...explodes.
um, they had to fill that can with that material the first time, didn't they?
Done under careful condition with control it is normally not a problem but consider that plain air is almost never used as an aerosol propellant because it might be so dangerous. I would have researched the chemical interactions first and then used a normally non-reactive gas such as refrigerant.
Best explanation of a fart
love the ronald mcdonald shoes 5 million thumbs up
thanks for watching and commenting
you got it
lol he said "personal lubricant for penetration" LOL
that was kind of cool i never know you can do that
Wow, you just saved me a ton. One of my grandkids held 2 new cans of WD-40 upside down to blow balloons up... I thought I'd be going to prison for murder, but now I'll be laughing at them while I show them I know more than they thought I did. Okay, I really don't, but that'll be our secret, okay? Now off to walmart to get a couple of those tire valves. Too bad my compressor only goes up to 80lbs... But, I can always refill the cans, can't I... Cool tip. Subscription coming because, I know I want to.
lol yes! thanks for watching and subscribing
love the shoes at the end :-) thumbs up
Thanks for watching and commenting
klowny1969
loved the shoes, and the video :-)
+Richard Downer thanks
Tjanks for sharing. Very informative and straight to the point. 💙💚
Nice shoes Klowny. The gas normally in the can is more compressible than air, so this won't last as long as the original fill. But air'll work in a pinch.
thanks for watching and commenting
Old farmer showed me this years ago. He just charged the can with a blow gun. Or tire air chuck directly on plastic nipple.
I will try that. Thanks Ronald
Thanks for watching
Only one suggestion and that is to insure that you do not overfill the can with compressed air or you will have a heck of a bomb going off in your hand. I would suggest a regulated air supply limited to 80 - 90 lbs of pressure at most. Plus as with a
tire it would be much better if you had it in a container to shild you from the can should it might burst. Glove would be a
help and wear safety glasses when doing somethig like ths.
gloves & safety glasses are for wimps..... that is what youtube is for. lets see if it works... HAHAHA.. messing with ya, true could make a person have a bad "few MONTHS"...... (see how I did not put days, it could be REAL BAD!)
Have a friend who did this after he saw the video. but he cheated he made a "Blast cage our of a piece of steel with a cap welded on top to prevent shaprnal from moving it it blew. Haven't seenit but he is an old military type and used to work EOD, still has all his body parts. LOL
James Maxwell
smart friend.. lets see what he built, for a blast cage??????? pics and video please :-)
James Maxwell yes mom, will do
James Maxwell thank you for this info and valuable tips.
Nice shoes!!! :)
Whoa, didn't know you could do that - that's pretty damn cool!
When you fill the bottle with a liquid, place some fitings around the male threads of the valve in order to get a bigger hole ( inversed reducers). Filling will be easier...
awesome! That's the best method I've seen. Thanks.
Nikolay K thanks for watching and commenting
Sweet!! Great tip. It will be useful some day.
thanks for watching
+abdul latif thanks
Good bless you. thanks Ronald. ... Venezuela Pura Vida...
thanks for watching
+klowny1969 fine, view this videos is important. More in Venezuela
I'm going to try this. One problem I have is that my spray paint cans seen to get stopped up somewhere in the line that runs from the bottom of the can up to the spray tip.
I am wondering about a similar thing. I am wondering how the companies can put paint cans in spray can form. Like if i got to a local hardware store or paint store get a paint matched in a paint can form. Is there a simple way with an air compressor i could take an empty aerosol can and fill it up with paint and compressed air to make my own spray can bottles? Because it sucks buying all these spray can bottles if i can wash out clean and reuses with other paints to make all different color aerosol spray cans from scratch. Because some time its hard to get a paint match in spray can form. I could uses a method similar to this to convert from can form to aerosol can form
Very good, I have too many full aerosal cans but no propellant. Thanks for posting. This is a thumbs up video, and a subscribe. Cheers !
Rons beers thank u
ha ha ha!! "...this is my favorite personal lubricant, penetrating oil" ha ha ha ha ha ha ha!
thanks for watching
Lmfao
lub and penetrate do make a sentence, you dirty mind lol
you can do this with butane lighter gas, it is much more effective, as the air will soon become depleted. I firstly charge the aerosol with the liquid to be sprayed, then chill it in the freezer in preparation for charging with butane propellant. chilling the aerosol allows a full charge of butane propellant to be put in.
cool, makes a great flamethrower
As any aerosol can is !
hey klowny i love that idea thats so cool man thanks a bunch dude !!!
thank you for watching and commenting
That Trizol is the best secret to loosen a bolt.
it is good stuff
I like Kroil or Aerokroil. I use PBBlaster on the easier jobs..
Top man thanks for this great money saving idea. cheers
thanks for watching
Your welcome man
Nice wheels, bud.
VERY COOL !!!! LOVE IT MAAAAN !
thanks
love the tip bro very clever cheers
thanks for watching
So simple, but it appears to work.
yes sir..thanks for watching and commenting
very nice video. i learned something new. thanks for sharing.
thanks for watching
Good job.....
I will try it.....So I will put in there like 80 psi or 90 right? thank... you.....good one....thumbs up!!
Hi..i watched you recharge that airsal can with that lubricant..and that was great.. and know ,..id like to ask you how do I recharge my can of propellant, for airbrushing..can you show me how buddy..my name is Emmett..and I'll be waiting on your response...thanks..
can you put paint in it? for instance some little bottles of acrylic paint and make that into spray paint?
sure can..thanks fo watching
Very good info...
Love the Shoes...LOL
very GOOD and Useful video
patrick driscoll 5hanks
LOVE THE SHOES HOMIE
Thank you
kudos for the clown shoes, but I hope your not clowning around showing us this tip. If you aren't then kudos for the amazing tip also. Something I would have never thought of. You can bet I'm trying this one out!
0:32 "This is my favorite personal lubricant, penetrating oil solvent"
+z0rak YES!!!!
You could solder the copper part of the valve into the can.
Make sure the valve of the can itself doesn't get to hot.
There are other videos which show how to do that.
will that work with any can of spray? like wd40?
Thanks Klowner!
thanks for watching and commenting