Hello friends, when you do it, use a thick tube, clean it before applying the glue, after gluing, let it take about 3 hours for the glue to harden, dilute the paint, compress the gas 3-4kg is safe. After using, you open the top cover to put gasoline in the washer and open the pump needle of the car valve to let the gasoline out chào các bạn khi làm các bạn sử dụng ống loại dầy, vệ sinh sạch sẽ trước khi dán keo sau khi dán xong để khoảng 3h cho keo khô cứng lại, sơn pha loãng, nén khí tử 3-4kg là an toàn. sử dụng xong các bạn mở nắp bên trên cho xăng vào xúc rửa và mở kim bơm của van xe cho xăng ra ngoài
through the fuel hose of a gasoline trimmer +, a syringe. We pump the paint into an empty balloon Finishing propane gas lighters It will be like factory paint. The viscosity of the viscometer to pick up . Translated via Google translator.
Молодец, парень дай бог тебе здоровья и благополучия новых творческих успехов и хорошего настроения хорошо, что придумал многоразовый балончик бывает так, что нужной аэрозольной краски не найдёшь, за-то можно самому подобрать какой тебе надо цвет🤝👍💪🇷🇺🛠️!!!
Honestly, I was annoyed last I was looking for a video or guide to make something similar since everyone said you can't make it or it wouldn't be safe... better were the days when you simply had a book to show you how to recharge your non-rechargeable batteries and use those piles of asbestos shingles you have lying around... I guess not everything aged well in those books, but still people back then assumed people were smart enough to not deviate from a guide and potentially kill themselves... I plan on using your design as a base for a refillable air blower. Thank you a million for the great guide, I look forward to making it :D
@@Unutop ну ё маё, ну хоть чуть-чуть голову включи, всмысле фантазию…. Припаиваешь металическое горлышко с резьбой, сверху крышка, типа как от фляжки армейской, а в крышку ниппель. Естественно всё через уплотнительные резинки.
Very good idea. Only problem is every time we have to use the correct amount of paint for the job. Because we have to clean the valve if not it will get stuck.
This idea is very cool, but also very dangerous, if this plastic can't handle the pressure and it bursts, it goes straight in your face, or it can burst in your hand, be very careful with pressurized pressure, it's very dangerous
hello but you can use the compressor for see how strong is this thing and test it with a lot more pression to see at what point he break this is what people do for air bottles for undersea
Thanks for sharing, it is a cool idea for sure and I will to try it. Just a tip for you, I think that you will find that you will get better results when using your adjustable pliers in the correct direction. You always tighten against the fixed jaw. It makes them easier to hold closed and the teeth in the jaws were made in this way. Most people don't know or think about it, so I thought I would just put it out there since you were nice enough for sharing your idea.
Có 1 vấn đề là trong sơn pha sẽ có axetone, không biết cao su và nhựa có chịu được khi ngâm trong axeton không? Làm để chống cháy thì ok chứ dùng lâu dài thì không ổn.
🇬🇷 Πάρα πολύ ωραία η ιδέα και η κατασκευή, συγχαρητήρια. Για να δούμε όμως εάν βγάζει αέρα η συσκευή, νομίζω ότι θα ήταν καλύτερα να τη βυθίσουμε ολόκληρη μέσα στο νερό. Τώρα εάν υπάρχει κάποιος άλλος λόγος, εγώ δεν το γνωρίζω.
На какую площадь хватает одной накачки воздухом? Баллоны с краской обычно наполняют специальным газом , а не воздухом потому что воздух в отличие от тех газов хуже сжимается . А раз хуже сжимается , то давление быстро спадет и нужно будет подкачивать баллон снова и снова.
Exelente una crítica constructiva uniera Sido mejor Aser el cuerpo con tubería roscable hasta para llenarla con mayor facilidad y por mejor seguridad saludo y éxitos en tus proyectos
Bonjour 😊 Vu que je suis français 🤔 il y a des mots que je ne comprends pas 😢😥 mais sinon c'est une super invitation 👍👍 bravo 👏 bravo 👏 vous êtes un génie 😯 🤘🤘🤘
I tried more or less the same patent, " Paint Bomb !!!!". The thinners dissolve the PVC Glue and then the "spray can" blow apart where the peaces are glued together with a very "loud bang" and paint every where. Use the same method, but just use metal piping (galvanize) that screw together. A bit heavier, but much much more secure.
You will not find leaks by putting bubbles over something that makes bubbles. Apply soapy water. NOT bubbles. How do you clean old paint out of your new spray can? Please learn to hold your pipe pliers correctly.
Its reusable! only you need is to clean after use, just as we do in spray guns(cleaning nozzel is a key), its a quality time spent to make as well cheap
B. Días amigo. Es buena idea amigo. Sin embargo es muy peligroso, no es un recipiente a presión, por lo tanto no cumple cumple con normas y es un peligro al cargarle el aire. Saludos desde México y que Dios te bendiga.
A leak test is not practiced like this, especially not with thousands of bubbles 😫😫 how can you see bubbles if there are several thousand bubbles 😵😵you have to soak in a basin of good hearing water Otherwise good job I think it's the most solid process I've had congratulations. 😵 😵
As a next level modifications you could get a spray gun and hose from harbor freight so you could change nozzle size. Maybe go with a little larger pipe so you could clean out. careful with pressure. If using latex paint, water will clean out.
Or just buy the fucking paint spray gun intended for this job in the first place for 13 dollars, you know since your already at Harbor Freight. At first I thought that what you comment was going to say
Сам баллончик то получился хороший и главное многоразовый, а вот распылитель там плохой и часто бывает даже новый балончик купишь, а распылитель нормально не работает, то плюется крупными каплями, то неравномерно распыляет. Придумайте как сделать самому хороший распылитель.
Распылитель тонкой проволокой или скобкой от степлера хорошо очищается. Просто после использования они обычно подсыхают, поэтому любой баллон лучше использовать весь сразу. Я вот недавно скобкой от строительного степлера проширнул и как новый!
Excelente para quê? no mercado existem pulverizadores para serem ligados aos respectivos compressores. De facto, os pulverizadores são seguros, têm um jacto regulável e não tens de fazer este trabalho inútil de cortar canos e colar os canos que depois de duas ou três utilizações se desprendem devido ao facto dos solventes dissolverem a cola.
My thoughts were the same as yours. This is so stupid. 13 dollars for a cheap hvlp paint sprayer and he probably would have spent less money than making this trash.
I don't see why it couldn't be done but it would add an extra point to leak from. Plus if it starts to leak once you have paint in there it will basically glue the threaded cap on.
Con algunos usos más es posible que se deterioren las gomas que hacen de sellos y el pegamento que unen los tubos con las tapas por los solventes que utiliza par diluir la pintura
Hello friends, when you do it, use a thick tube, clean it before applying the glue, after gluing, let it take about 3 hours for the glue to harden, dilute the paint, compress the gas 3-4kg is safe. After using, you open the top cover to put gasoline in the washer and open the pump needle of the car valve to let the gasoline out
chào các bạn khi làm các bạn sử dụng ống loại dầy, vệ sinh sạch sẽ trước khi dán keo sau khi dán xong để khoảng 3h cho keo khô cứng lại, sơn pha loãng, nén khí tử 3-4kg là an toàn. sử dụng xong các bạn mở nắp bên trên cho xăng vào xúc rửa và mở kim bơm của van xe cho xăng ra ngoài
check it is fart proof👨🏭;
Qqqqqqqqq1qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq
through the fuel hose of a gasoline trimmer +, a syringe.
We pump the paint into an empty balloon
Finishing propane gas lighters
It will be like factory paint.
The viscosity of the viscometer to pick up .
Translated via Google translator.
Rất hay hay hay hay hay hay hay ❤❤❤❤
Ccccxcccccxccxccxccc@@TANTRAN-jw1nx
Very creative video. I didn't expect paint sprayer to be made this way. Congratulations.
Hey, all I could say after watching this is;
"YOU'RE TOO GOOD MAN!"
......... Instead you are a genius.
Молодец, парень дай бог тебе здоровья и благополучия новых творческих успехов и хорошего настроения хорошо, что придумал многоразовый балончик бывает так, что нужной аэрозольной краски не найдёшь, за-то можно самому подобрать какой тебе надо цвет🤝👍💪🇷🇺🛠️!!!
Wauw wauw mantap keren abiis ide kreatifnya sy suka 👍👍👍👍👍👍👍
Sáng tạo.hay wa đó Sơn
Dạ cháu cám ơn cô
very clever jig. thanks for including the dimensions too.
Honestly, I was annoyed last I was looking for a video or guide to make something similar since everyone said you can't make it or it wouldn't be safe... better were the days when you simply had a book to show you how to recharge your non-rechargeable batteries and use those piles of asbestos shingles you have lying around... I guess not everything aged well in those books, but still people back then assumed people were smart enough to not deviate from a guide and potentially kill themselves... I plan on using your design as a base for a refillable air blower. Thank you a million for the great guide, I look forward to making it :D
you are a genius , you are very clever , you are very good
Гениально, из баллончика сделал баллончик👍.
Из одноразового баллончика сделал многоразовый баллончик. Теперь понятно?
@@Unutop то есть в одноразовый баллончик нельзя что-ли клапан впаять???
@@Aisi-304 а краску как заливать?)))
@@Unutop ну ё маё, ну хоть чуть-чуть голову включи, всмысле фантазию….
Припаиваешь металическое горлышко с резьбой, сверху крышка, типа как от фляжки армейской, а в крышку ниппель. Естественно всё через уплотнительные резинки.
reir de algo formidable, triste personita.
Hay Quá Thầy Ơi! Em sẽ làm 1 cái để sơn xe Nhưng sẽ làm to hơn
ok bạn!!!
Làm to quá ko nhấc nổi đâu bạn, ko linh hoạt. Lại thêm phải bấm để sơn nữa chắc gãy tay. 😅
Tuyệt vời anh ơi
thanks bạn!!! chúc kênh của bạn ngày càng phát triển
@@sonlai cảm ơn Anh
Very good idea. Only problem is every time we have to use the correct amount of paint for the job. Because we have to clean the valve if not it will get stuck.
If you invert the can and blow air through it like the original cans.. should work.. but why was the paint lacking misting very large drops coming out
Rất hữu ích , cám ơn anh ...!
thanks bạn!!!
Chào bạn bạn chia sẻ video tuyệt vời quá bạn ơi chúc bạn sức khỏe thành công hẹn gặp lại bạn 👍👍❤❤❤❤❤❤
Rất hay Lắm ❤❤❤❤❤
So creative .
Thank you so much .
I am from SRI LANKA.
Hay lắm anh Sơn
hơi nguy hiểm, đang bơm nó nổ cái bùm, sơn bay đầy người có khi mù mắt luôn 😂
Habría que saber a cuantos BAR/PSI llenar por que si puede terminar en desastre jaja
Paint solvent can easily damage (soften) PVC. It is a color bomb 🎉 if you leave it pressurized somewhere
I wonder about the rubber seals and if they can resist solvents.
đã từng lm với bình atm nhưng cho sơn vào hơi khó, bình này cải tiến cho sơn dễ hơn
ok bạn
đầu cho sơn vào vẫn nhỏ, cải tiến là gắn thêm cái zacor vào để cho sơn dễ hơn
Mua cái phiểu (loại nhỏ) bằng inox 304 thì rót sơn vào bình ok - Trên lazada có bán cái phiểu nhỏ này khoảng 50k/cái
Amazing DIY. THUMBS UP
This idea is very cool, but also very dangerous, if this plastic can't handle the pressure and it bursts, it goes straight in your face, or it can burst in your hand, be very careful with pressurized pressure, it's very dangerous
hello but you can use the compressor for see how strong is this thing and test it with a lot more pression to see at what point he break this is what people do for air bottles for undersea
Thanks for sharing, it is a cool idea for sure and I will to try it. Just a tip for you, I think that you will find that you will get better results when using your adjustable pliers in the correct direction. You always tighten against the fixed jaw. It makes them easier to hold closed and the teeth in the jaws were made in this way. Most people don't know or think about it, so I thought I would just put it out there since you were nice enough for sharing your idea.
Có 1 vấn đề là trong sơn pha sẽ có axetone, không biết cao su và nhựa có chịu được khi ngâm trong axeton không? Làm để chống cháy thì ok chứ dùng lâu dài thì không ổn.
🇬🇷 Πάρα πολύ ωραία η ιδέα και η κατασκευή, συγχαρητήρια. Για να δούμε όμως εάν βγάζει αέρα η συσκευή, νομίζω ότι θα ήταν καλύτερα να τη βυθίσουμε ολόκληρη μέσα στο νερό. Τώρα εάν υπάρχει κάποιος άλλος λόγος, εγώ δεν το γνωρίζω.
Một ỷ tưởng rất hay và tuyệt Vời Ông Mặt Trời ☀️ luôn Bác Nhỉ. Cắm Ơn Bác đã chia sẻ...❤️❤️❤️👬👍👬❤️❤️❤️
thanks bạn!!!
fun project. good if you have all of those supplies at home. Otherwise easy to go buy new spray paint.
Однажды этот баллончик смачно звезданёт!
Для чего вся эта дрочь нужна была ? паяльник и сосок нужен был ...
Хорошо, если при накачке, всего лишь все краской заляпает, а если к руке при встряхивании..?
Rất sáng tạo.👍
Very smart idea. But I suggest using high-pressure resistant PVC... (The blue one in my country).
На какую площадь хватает одной накачки воздухом? Баллоны с краской обычно наполняют специальным газом , а не воздухом потому что воздух в отличие от тех газов хуже сжимается . А раз хуже сжимается , то давление быстро спадет и нужно будет подкачивать баллон снова и снова.
Great job, great idea 👏💡
Awesome Brilliant idea Bro
Gioăng cao su làm từ săm xe máy gặp xăng liệu có ổn không bạn?.
So creative, wonderful, can apply and use for many colors, thanks so much.
thanks!!!
Exelente una crítica constructiva uniera Sido mejor Aser el cuerpo con tubería roscable hasta para llenarla con mayor facilidad y por mejor seguridad saludo y éxitos en tus proyectos
Nice share man, thankful
Bonjour 😊 Vu que je suis français 🤔 il y a des mots que je ne comprends pas 😢😥 mais sinon c'est une super invitation 👍👍 bravo 👏 bravo 👏 vous êtes un génie 😯 🤘🤘🤘
Vậy dùng bình cũ thêm chỗ vào sơn và lắp vòi bơm honda vào thì lẹ hơn không ?
Bỏ nước ớt vào làm xịt hơi cay ngon à
I tried more or less the same patent, " Paint Bomb !!!!". The thinners dissolve the PVC Glue and then the "spray can" blow apart where the peaces are glued together with a very "loud bang" and paint every where. Use the same method, but just use metal piping (galvanize) that screw together. A bit heavier, but much much more secure.
Có một vấn đề với các gioăng cao su khi tiếp súc với xăng và xăng thơm
Good way to make a paint bomb 🎉
Excelente idea 😊
Já contratei um engenheiro da NASA, para fazer uma dessa pra mim...kkkkkk
You will not find leaks by putting bubbles over something that makes bubbles. Apply soapy water. NOT bubbles.
How do you clean old paint out of your new spray can?
Please learn to hold your pipe pliers correctly.
А мне компрессор понравился - мощненький и маленький...
Thank you for this tuto. What kind of paint did you use ? Paint for car can also be used?
It's going to have to be pretty thin. Should be able to use pretty much any fluid as long as it's not to viscus.
Hay lắm nhưng chỉ xài đươc 1 lần thì lổ nặng!!!
mình dùng sơn gốc nước được ko ạ
cool idea but why not use a cheap spray gun? You'll get better results.
Bình này chiuj đuoc áp lực bao nhiêu psi vậy add?
a mua cái ốc nắp nhựa i ơ đâu đấy
Congratulations 🎉🎉🎉🎉
Good stuff used for WD 40 to😊❤
Способ крепления клапана баллончика к горловине шикарен 👍
Бесполезная самоделка, хватит на 2 пшика, через пару часов краско внутри засохнет, нужно заправлять пропаном, все балончик и заполняются газом))
That best for all ❤❤❤❤
Нормально наверно мыльными пузырями проверять на пузыри! Мастер от бога!
Parece un explosivo...!!😂😂😂
very good idea 👍👍
KEREN BANG, CERDAS SEKALI
Its reusable! only you need is to clean after use, just as we do in spray guns(cleaning nozzel is a key), its a quality time spent to make as well cheap
nice
Muito legal
Vou copiar
Deus te abençoe em nome de Jesus...
Amazing good job 🤩🙇👍👍👍
Can it be easily cleaned? For example if I want to use different paint color. Because thinner agent might damage the PVC..
There is thinner in the paint once he thinned it down. If you are worried about that use latex paint.
@@user-neo71665 yes. I can see that. I meant thinner agent to clean the tube if one wants to use other paint color.
Bạn ơi mình chế nó cứ bị tắc sơn là sao vậy chỉ dùm mình với
do sơn pha đặc quá đó bạn và trước khi dán ống vệ sinh cho kỹ
@@sonlai ô kê bạn càm ơn bạn nhiêu chúc bạn mỗi ngày có một video mới
Xài một thời gian có phải thay ống nhựa nhỏ bên trong không? Mình nghĩ nó sẽ bị sơn bám vào nhiều sẽ bị nghẹt ông
B. Días amigo. Es buena idea amigo. Sin embargo es muy peligroso, no es un recipiente a presión, por lo tanto no cumple cumple con normas y es un peligro al cargarle el aire. Saludos desde México y que Dios te bendiga.
sử dụng xong cho xăng vào xúc rửa là ok nhé bạn
Chú cho hỏi là nên bơm bao nhiu kg thì được, chú có thử ngưỡng cao nhất của cái bình nhựa này chịu được bao nhiu kg không?
bình nhựa dán xong để khoảng 2 tiếng bơm 3 - 4kg là vô tư bạn nhé
A leak test is not practiced like this, especially not with thousands of bubbles 😫😫 how can you see bubbles if there are several thousand bubbles 😵😵you have to soak in a basin of good hearing water Otherwise good job I think it's the most solid process I've had congratulations.
😵 😵
As a next level modifications you could get a spray gun and hose from harbor freight so you could change nozzle size. Maybe go with a little larger pipe so you could clean out. careful with pressure. If using latex paint, water will clean out.
Or just buy the fucking paint spray gun intended for this job in the first place for 13 dollars, you know since your already at Harbor Freight. At first I thought that what you comment was going to say
На баллоне четко написано :" Не разбирать и не бросать в огонь" . Какой то другой распылитель и получится прекрасная идея .
Это пишут для рукожопов, им действительно ничего нельзя делать с баллоном
Сам баллончик то получился хороший и главное многоразовый, а вот распылитель там плохой и часто бывает даже новый балончик купишь, а распылитель нормально не работает, то плюется крупными каплями, то неравномерно распыляет. Придумайте как сделать самому хороший распылитель.
Распылитель тонкой проволокой или скобкой от степлера хорошо очищается. Просто после использования они обычно подсыхают, поэтому любой баллон лучше использовать весь сразу. Я вот недавно скобкой от строительного степлера проширнул и как новый!
Jajaja prefiero comprar la pintura lista que Haser ése desmadre 😅😅😅
I will be sure to “check to see if it fart”. Thank you
Excelente! Ótima idéia ! RJ - Brazil.
Excelente para quê? no mercado existem pulverizadores para serem ligados aos respectivos compressores. De facto, os pulverizadores são seguros, têm um jacto regulável e não tens de fazer este trabalho inútil de cortar canos e colar os canos que depois de duas ou três utilizações se desprendem devido ao facto dos solventes dissolverem a cola.
My thoughts were the same as yours. This is so stupid. 13 dollars for a cheap hvlp paint sprayer and he probably would have spent less money than making this trash.
@@drewrinker2071 in Brazil the same is arround on 200 dollars (no conversion, comparison by minimum wage) so is very cheap to diy
Why not thread one of the end caps to allow for cleaning and easier pouring in of paint etc?
Because = RUSSIA
I don't see why it couldn't be done but it would add an extra point to leak from. Plus if it starts to leak once you have paint in there it will basically glue the threaded cap on.
Excelente, útil, engenhoso
1 lần đổ vào bao nhiêu ml sơn vậy anh???
Excelent 🎉❤😂
Genial gracias bendiciones
What is the use of doing this thing? the sprayers to be connected to the compressors are always on the market and have a paint jet adjustment.🤣🤣🤣🤣
Quá siêu !
good idea, thank you
Thank you!!! Wish the channel grows more and more
No será mejor ir a la ferretería y comprar una lata de pintura 😅😅
Las latas de Aerosol están muy caras!
Tren ca tuyet voi
Con algunos usos más es posible que se deterioren las gomas que hacen de sellos y el pegamento que unen los tubos con las tapas por los solventes que utiliza par diluir la pintura
Evidentemente no es el método y materiales definitivos
Tiene más problemas inclusive
Thử xì sao không ngâm cả bình vào thau nước nhỉ , làm vậy phiền phức quá .
Wchich motor you use for fill air
Muito interessante, só música que é cansativa,podia colocar só algumas vezes
Coleccionaba las bolitas o canicas que venían en los tarro de pintura. Deben estar guardadas ahora vienen piedras 😊
Just get an airless sprayer and air compressor. Tons easier
Keo gặp xăng thơm pha sơn lâu ngày nó tróc ra hết còn đâu. Thấy lấy keo pvc dán là ko ổn rồi
Sir, Good technical skill.
Prepared empty can be sold to us.1 piece. What will be cost.
Or tell how we can get.any address pl.
Harus di berikan tekanan angin lebih tinggi supaya semburan lebih kuat dan dapat menyembur lebih halus dan lebar😊
Đổ bao nh sơn ah oi
nữa bình thôi bạn
How much pressure?
Có bán ko ban
yg jdi pertanyaan? dlm benak saya. itu lem klau ter,rendam sama bhn campuran cat,seperti bensin/thiner. apa tidak lepas?