Seriously man I've got commend you on working in really tough conditions outside in the street without any proper lifts and you don't even complain once ,cheers man
I would have replaced the throw out bearing for the same reason you replaced the rear main. It's cheap and it'll drive you nuts if it starts to go. Chances are the clutch will die long before the bearing in this case especially with forced induction right? Can't wait to see!
Agreed I probably should of replaced it but I’m getting my original corolla c60 fully rebuilt with carbon synchros so I’m sure I’ll swap it out before the throw out bearing gets to that point. But then again throw out bearing had 35k miles Original Rear main seal had 230k miles Yea Greddy supercharger sitting in my garage waiting to be installed
Hey man love your videos! I just got a xrs 2005 Corolla and I put a hole on the tranny and I was looking at the celica gts 2000 and it looks like the transmission is the same I was wondering if I’ll fit without a problem! Thank you
Thanks for the part numbers! Is it cheaper at dealerships?? I also need the bolts to go to the bell housing since one of mine is missing -_- and the throw out bearing, how would you know it’s bad?? Thanks a lot bro!
Did you figure out where the vibration came from when you're on 2nd gear? I just did my clutch flywheel both axles and now I'm getting that vibration same speed and RPM
27ft lbs seems like a lot for a small 12mm bolt. Honestly it’s the flywheel bolts that are much more important since it’s the one attached to the engine. I just did the pressure plate bolts tight enough since I read online 14ft lbs and that’s not a lot. Just be careful to not tighten it too much of you will strip it
Have you ever been able to remove a manual C60 transmission off a 2zzge engine without removing the whole engine? I just reinstalled my 2zzge engine back in and I"m now having problems shifting into 6th gear. I'm hoping I don't have to remove the whole damn engine again in order to remove the transmission any input would be appreciated.
![[LIVE] : ONE ลุมพินี 78 | คู่เอก "ปกรณ์ vs ฟาบิโอ"](http://i.ytimg.com/vi/LSOmgl0Th2c/mqdefault.jpg)
Seriously man I've got commend you on working in really tough conditions outside in the street without any proper lifts and you don't even complain once ,cheers man
thanks fam! gotta do what i gotta do to get it back on the road.
The real test is some hard pulls 🤪
What was that pull at the end of the video lmao 😂
Your dedication is top notch bro
Thanks fam
Just dropping by to give you a like. I'm stoked to see the corolla back! I'm saving this video for when my c60 inevitably explodes. 😅 Much love bro!
thanks fam! I appreciate it
Great video! Good tips to catch here. That auto touch as u got out is on point
Glad you liked it
Keep doing what your doing bros i support what you do since day.. ill keep sharing to friends to family to make you hood famous lol😅
thanks fam! appreciate it!
Keep up the good work brother
Thanks, will do!
'pizza mind'
lmao
I hate working in the street. It's like taking a shit in a public bathroom with no stalls.
lmao wow i guess i can see that hahaha
Banging gears shedding tears🥲
there ya go lol
I would have replaced the throw out bearing for the same reason you replaced the rear main. It's cheap and it'll drive you nuts if it starts to go. Chances are the clutch will die long before the bearing in this case especially with forced induction right? Can't wait to see!
Agreed I probably should of replaced it but I’m getting my original corolla c60 fully rebuilt with carbon synchros so I’m sure I’ll swap it out before the throw out bearing gets to that point.
But then again throw out bearing had 35k miles
Original Rear main seal had 230k miles
Yea Greddy supercharger sitting in my garage waiting to be installed
@@2zzlow im surprised you’re supercharging a car with a 1/4 million miles on it
morning work videos ftw
You know it
@@2zzlow 12:30 lowkey wanted to see the list of part numbers for all the mounts in the description
Come on Valvoline sponsor this young man!!!
Exactly! Lmao 😂
Hey man love your videos! I just got a xrs 2005 Corolla and I put a hole on the tranny and I was looking at the celica gts 2000 and it looks like the transmission is the same I was wondering if I’ll fit without a problem! Thank you
follow this video th-cam.com/video/f2jjpNaYlo0/w-d-xo.html
nice vid.. i think i would go chromolly.. had aluminum one in my mr2... flex at high rpms scare me.
ill consider it for next time thanks
Thanks for the part numbers! Is it cheaper at dealerships?? I also need the bolts to go to the bell housing since one of mine is missing -_- and the throw out bearing, how would you know it’s bad?? Thanks a lot bro!
Get them off toyotapartsdeal.com
Spin the bearing and make sure it doesn’t bind or grind
@@2zzlow thanks bro! Thank god I procrastinated lmao
I'm having trouble removing my driverside axel , I tried to use the shift fork method , can't get it to fit
Is it a c60 fork? It only work one way also so try both sides
En qué parte de California estás?
Pregunta hay que hacer modificaciones para instalarla una transmisión de celica a corolla?
stockton y si hermano tengo un video pa transmission de celica para corolla
Did you figure out where the vibration came from when you're on 2nd gear? I just did my clutch flywheel both axles and now I'm getting that vibration same speed and RPM
had a bad motor mount and ended up replacing my axles
Cual es la ventaja de que tenga tracción en las dos ruedas, correr mejor en alta o para arranque que agarre mas?
por las curvas entrar mas rapido
where you plan on buying the sugercharger kit for the 2zzge?
Follow my Instagram, I already have one and it’s going in soon
I recently installed an act clutch. I looked up torque specs and saw 27ft lbs. You say 14ft lbs. Would tightening it down too much cause problems?
27ft lbs seems like a lot for a small 12mm bolt.
Honestly it’s the flywheel bolts that are much more important since it’s the one attached to the engine.
I just did the pressure plate bolts tight enough since I read online 14ft lbs and that’s not a lot.
Just be careful to not tighten it too much of you will strip it
💯👍
thanks fam!
What oil is reccommended for the c60 lsd?
Is it hard installing a C-60 Transmission also how long does it take to install?
its not hard, about 8 hours or so to remove and install
are you in arizona?
california
Hey bro what oil is best for the transmission in your opinion?
i just use Valvoline synchromesh
Have you ever been able to remove a manual C60 transmission off a 2zzge engine without removing the whole engine? I just reinstalled my 2zzge engine back in and I"m now having problems shifting into 6th gear. I'm hoping I don't have to remove the whole damn engine again in order to remove the transmission any input would be appreciated.
thats alot of work, its easier to just remove both and reinstall both at the same time.
@@2zzlow Update: I got the transmission removed off with the engine still in.