Thank you for posting such a comprehensive video but I think we would all like to see the actual fix.? Please let us see the bent bracket pedal fix. :)
I had a similar problem with my 2009 2.4 TDI Transit. Turned out to be loose wires from the accelerator pedal where my aftermarket cruise control had been connected. I did have "limp mode" issues before the cruise was fitted and the mechanic feels that the wiring may have been the problem from the start. All error codes have now cleared.
Hi, I have a 2009 mk7 transit motor 2.2 puma TDI. My problem startet like 2 years ago with the rpms oscilating from 750 to 850 at ralenti, but power remain normal. Nowadays the engines turns off suddenly when I stop at the traffick lights or when I downshift. Once it turns off I can restart it normally but it starts with a little bit of black smoke. The power loss is not dramatic but its not the same than 3 monts ago. What can be my problem cause? I hope you to help me cus I fell lost with this.
Usually they're attached to a bracket that is part of the brake pedal assembly, not the brake pedal itself. The bracket/tab where they seat, can be knocked out of position. Rather common problem in certain designs! So when people drive should avoid "kicking" with their feet like a spoiled brat! This is the result! LOL 😂 Small feet are an added advantage! ;-)
I have the same problems with my car ,the same model ,and the same errors i have no accelerate and it smoke sometimes ,after 10 min running are working perfectly
Do you service your vehicle regularly? I have had my FORD TRANSIT for thirteen years. I have had no problems. I had a limited slip differential installed - ETON Detroit True track.
The greatest problem with the Ford Transits in Australia is rust in the roof and the rear area. I have had my Ford Transit fully treated and all rust removed.
Due to the faulty paint adhesion, FORD Australia and I are negotiating for new paintwork. In every other aspect, my Ford Transit has been brilliant. I know nothing about the new models.
Hi I have a mwb 12 plate transit when I'm driving the engine malfunction light can come on then lose power i turn key of and on then it can work again i have had egr deleted and changed the fuel filter and it's still doing it can you Can you recommend anything thanks
@@aisforabbie7217 - "...coming up with loads of stuff that's not correct..." Using some basic logic, there's a reason, or several reasons, why it's coming up with "loads of stuff". Identify and take care of them on a logical way. Until all are solved! Point being if it's "not correct", why is it showing up in the first place?! As one of my mechanics teacher used to say! Machines are always right! LOL 😂 You just have to them figure out... pure logic!! Easier to say than do, maybe! But the fact remain that guess work will not cure it. ;-) Cheers
It’s not a fault. Service reminder light. Ignition on, Hold down brake and accelerator pedals for about 10-20sec it will flash and go away. Also, maybe service the van too.
Hi there, can anyone please tell me where this sensor and bracket that was bent up, my van is driving me mental with a simular problem. If anyone could help that would be great
Great video on this type of transit does anyone know where the passenger side passenger air bag is? It’s not the one in the dash I know that much thanks in advance if anyone knows
again another great video the new forscan software it would be great if u could do a review with elm connected was thinking of buying one to play with always try to share new toys with your you tube followers thanks
Hi my transit mk7 2.4 power lost. Turbo only boosts so far with black smoke. Turbo actuator makes that same noise. And the actuator arm is very stiff. ODB 2 says P2563 Hope you can help. Thank you
Ive got the exact same van. Which is a campervan. So today i put the actuator on the broken van. And still the same. The actuator arm there is no movement. Stiff and wont move. Turbo is whilsting fine but only at low revs. Cant drive on motorway with it. Thank you
Im not a mechanic unfortunately. Just a carpet fitter. And its my work van.. Just trying to self diagnose . Does this mean a new turbo is required or can the turbo lever be replaced or repaired. Thank you
LM Auto Repairs I bought a E90 330i without cruis control. If I want to add this option I need to change KOMBI and also add the LDM module for braking when lower speed with cruisecontrol. Googled to find the answer but no success.
@@ChangoeMotorsport Hi I think.... and I have not investigated... but I think you don't need to replace nothing... You will need a steering wheel module, or stalker with the lever for the cruise control... from there, is only coding...
LM Auto Repairs thats what i already did but my car is before 09/2006 and after the brake function has built in to ABS module. I dont know how to connect this module to the FRM and the CAS
The secondary battery has a relay which shuts off after a while too stop it draining the start battery. If the second battery is flat you will have starting issues and the central locking will not work.
@@LMAutoRepairs ive a ford transit 09 plate with a limp mode prob. you can drive for aprox half an hour with no prob from cold. then when you slow down through the gears as soon as you frop to about 1 1/2 thousnad revs it goes into limp mode, turn engine off re set then drives ok until you slow down again
@@andyp9678 Changing bits without proper diagnose is exactly that... luck... you might fix it, you might not... And in the mean time, you are wasting your hardly earned money... Get is scanned, see what codes are stored or present on the ecu... and look at the live data while the problem occurs... Hopefully will be something that starts to point you in the right direction...
![MV วิถีชีวิตใต้ - ผา อัยย๊ะ [Official MV HD]](http://i.ytimg.com/vi/nODlkOUu9B0/mqdefault.jpg)
Great Video, thanks for sharing!👍
Hi
Thanks!
It is a privilege to have a comment from you!
Really appreciated!
Happy to be on board sir!
@@Diagnosedan
👍
Good .... Nobady will throw stones you are jenious technician👍
😋
Thank you for watching!
👍👍👍👍
Thank you for posting such a comprehensive video but I think we would all like to see the actual fix.? Please let us see the bent bracket pedal fix. :)
I will... Next time I come across this issue...
Thank you for watching and for your comment!
@@LMAutoRepairs I have the same problem can you tell us the issue please 🙏
you are amazing man, how come i didnt know about your channel. your great man.
😊
Thanks!
We re injuy waching for ur chanal
Thanks!
👍👍
Great video & explanation. Always learning thanks.
Thank you for watching and for your comment!
👍👍👍👍
FORScan also works flawlessly with ELM327. No need for Ford VCM!
Hi
I know... but I already had the Ford VCM... and this way avoid another cable in the case... :-)
Thank you for watching!
I had a similar problem with my 2009 2.4 TDI Transit. Turned out to be loose wires from the accelerator pedal where my aftermarket cruise control had been connected. I did have "limp mode" issues before the cruise was fitted and the mechanic feels that the wiring may have been the problem from the start. All error codes have now cleared.
👍👍👍
Thank you for watching and for your comment!
¹
super video and great fix i use forscan and must say its a great bit of software
Indeed it is... thank you for watching Paul!
My Ford Transit is a 9 seater fully trimmed vehicle.
Awesome find mate once again good job
Hi
Thanks!
👍👍👍
Hi, I have a 2009 mk7 transit motor 2.2 puma TDI.
My problem startet like 2 years ago with the rpms oscilating from 750 to 850 at ralenti, but power remain normal. Nowadays the engines turns off suddenly when I stop at the traffick lights or when I downshift. Once it turns off I can restart it normally but it starts with a little bit of black smoke. The power loss is not dramatic but its not the same than 3 monts ago. What can be my problem cause? I hope you to help me cus I fell lost with this.
Scan the van, and check live data...
Otherwise is pure guess work...
Thank you for watching!
SCV and or possibly ignition switch
This was my issue after racking my brains for 2 days wasting time at the turbo and fueling -_-
☺️
👍👍👍
Has this one got 2 batteries? The aux battery being low could have cause the dash and blowers to go off.
Good point... I have not checked? As I was only asked to look at the this issue...
But I know what you mean, I had that issue in the past!
👍👍👍👍😬😬
This model with two batteries - the two batteries are in parallel.
Where were the the brake pedal sensors. Are they attached at the brake pedal itself? Did you bend them to get the on off. Thanks
Usually they're attached to a bracket that is part of the brake pedal assembly, not the brake pedal itself. The bracket/tab where they seat, can be knocked out of position.
Rather common problem in certain designs! So when people drive should avoid "kicking" with their feet like a spoiled brat! This is the result! LOL 😂
Small feet are an added advantage! ;-)
I have the same problems with my car ,the same model ,and the same errors i have no accelerate and it smoke sometimes ,after 10 min running are working perfectly
Check for codes, and live data during cold start... it might help...
Thank you for watching!
Do you service your vehicle regularly? I have had my FORD TRANSIT for thirteen years. I have had no problems. I had a limited slip differential installed - ETON Detroit True track.
Always good video and info thanks for sharing . cheeeers
Thanks!
The greatest problem with the Ford Transits in Australia is rust in the roof and the rear area. I have had my Ford Transit fully treated and all rust removed.
Here is not much different...
Plus on the underside, due to the salt...
👍👍👍
Due to the faulty paint adhesion, FORD Australia and I are negotiating for new paintwork. In every other aspect, my Ford Transit has been brilliant. I know nothing about the new models.
@@andrewphillips4897 also pull all the sponge rubber sound deadenining from between panels etc
Hi I have a mwb 12 plate transit when I'm driving the engine malfunction light can come on then lose power i turn key of and on then it can work again i have had egr deleted and changed the fuel filter and it's still doing it can you
Can you recommend anything thanks
Yes... scan the car an look at live data...
Otherwise is pure guess work...
Thank you for watching!
Hi I have but it coming up with loads of stuff that's not correct I had them checked out but still doing it
@@aisforabbie7217 - "...coming up with loads of stuff that's not correct..." Using some basic logic, there's a reason, or several reasons, why it's coming up with "loads of stuff". Identify and take care of them on a logical way. Until all are solved!
Point being if it's "not correct", why is it showing up in the first place?! As one of my mechanics teacher used to say! Machines are always right! LOL 😂 You just have to them figure out... pure logic!!
Easier to say than do, maybe! But the fact remain that guess work will not cure it. ;-) Cheers
It’s not a fault. Service reminder light. Ignition on, Hold down brake and accelerator pedals for about 10-20sec it will flash and go away. Also, maybe service the van too.
Possibly....
Thank you for watching and for the suggestion...
Hi there, can anyone please tell me where this sensor and bracket that was bent up, my van is driving me mental with a simular problem. If anyone could help that would be great
Great video on this type of transit does anyone know where the passenger side passenger air bag is? It’s not the one in the dash I know that much thanks in advance if anyone knows
This model had only one Air Bag - Drivers side only.
again another great video the new forscan software it would be great if u could do a review with elm connected was thinking of buying one to play with always try to share new toys with your you tube followers thanks
Hi my transit mk7 2.4 power lost. Turbo only boosts so far with black smoke. Turbo actuator makes that same noise. And the actuator arm is very stiff. ODB 2 says P2563
Hope you can help. Thank you
Check either that the turbo is not getting sized, or that the actuator is working correctly...
Thank you for watching!
Ive got the exact same van. Which is a campervan. So today i put the actuator on the broken van. And still the same.
The actuator arm there is no movement. Stiff and wont move. Turbo is whilsting fine but only at low revs. Cant drive on motorway with it. Thank you
If the turbo lever is not moving, you have your answer...
Im not a mechanic unfortunately. Just a carpet fitter. And its my work van.. Just trying to self diagnose . Does this mean a new turbo is required or can the turbo lever be replaced or repaired. Thank you
Might be possible to clean the turbo etc... but most likely will require disassemble it...
hi my friend were did you buy the ford scan tool ?
Pretty sure was ebay... if I recall correctly...
👍👍👍
Can you tell whats wrong I have same problem with my van
Have you watched the video?
I have explained what was wrong in this case...
It's half hour long mate, just put it in the description
Silver bullets?
Not here... sorry...
Hi I was just wondering was the brake lights on with the fault.
That's a good question... I never checked... lol
😋
Useful video
Thank you for watching!
Fantastic video thanks for sharing, where are you based please?
Hi
Cambridgeshire...
Thank you for watching!
Oh that's a shame I could have used your services with my ldv convoy but I'm up north :-(
@@robnicolson2747
Lol
No worries...👍
Haha keep posting though mate great info on the dark magic pcm/ecus!
Have you had any experience with the dpc-655 pcm, it's the one fitted to my ldv convoy but believe it's ford derived?
LIKE BEFORE WATCHING
😋
Thanks!
I saw this problem on renault trafics and peugeots
Thank you for sharing!
👍👍
Great videos man! Learned a lot from your vids! Did you every had a BMW without a LDM module?
Hi
Thanks... without the LDM?
What do you mean?
LM Auto Repairs I bought a E90 330i without cruis control. If I want to add this option I need to change KOMBI and also add the LDM module for braking when lower speed with cruisecontrol. Googled to find the answer but no success.
@@ChangoeMotorsport
Hi
I think.... and I have not investigated... but I think you don't need to replace nothing...
You will need a steering wheel module, or stalker with the lever for the cruise control... from there, is only coding...
LM Auto Repairs thats what i already did but my car is before 09/2006 and after the brake function has built in to ABS module. I dont know how to connect this module to the FRM and the CAS
@@ChangoeMotorsport
🤔
Have you checked wiring diagrams?
The secondary battery has a relay which shuts off after a while too stop it draining the start battery.
If the second battery is flat you will have starting issues and the central locking will not work.
Thanks.
Hello I have same problem and the mechanic say to change fuel pressure vail sensor,my van lost the power!
Hi mate did that fix the issue
@@tryhardgaming5798 no
I have the problem with my transit recovery
Has any person had Air Conditioning fault? The hot will not turn off and the fault is not with the dials or the controls.
are you in the uk?
Yes...
Thank you for watching!
where are you based
Hi
What are you looking for?
@@LMAutoRepairs ive a ford transit 09 plate with a limp mode prob. you can drive for aprox half an hour with no prob from cold. then when you slow down through the gears as soon as you frop to about 1 1/2 thousnad revs it goes into limp mode, turn engine off re set then drives ok until you slow down again
@@andyp9678
Have you scanned the van?
@@LMAutoRepairs ive had my local garage change injectors and other bits and pieces with no luck
@@andyp9678
Changing bits without proper diagnose is exactly that... luck... you might fix it, you might not...
And in the mean time, you are wasting your hardly earned money...
Get is scanned, see what codes are stored or present on the ecu... and look at the live data while the problem occurs...
Hopefully will be something that starts to point you in the right direction...
steering angle sensor
Ok
ive seen your elongated video and i dont understand what youve found. CONFUSED.COM
Unfortunately you need some understanding about cars to understand my videos...
Nothing I can about that...🤷♂️
Still, thank you for watching!
👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍❤️
☺️
Thanks!
👍👍👍