1200 W at 91 % efficiency is 27 amps from battery. Do you think, that this thin nikel stripes can handle 27 amps in hot summer +38 *C all time till 47 V at battery terminals ?
7 หลายเดือนก่อน +21
I dont think you can't get more professional than this. Narration, layout, camera angle, sound... Everything is wonderful.
Yes, 2 temp sensors, and what will BMS do, if one of 70 cells get hot over 140 *C, SOC will be 100 % and thermal runaway will begin in midnight time, when people are in bed and near bed is ebike ? Ebike starts to produce H2, CO, CO2, HF, C2H2, CH4 etc. One spark and all house go to heaven.
I have built & bought several ebikes, currently rebuilding 2 that were damaged by flood waters from hurricane Ian in Florida and a new BBSHD fat bike build. Mechanically I can pretty much repair or replace anything on a bike, but that battery build blew me away. Very impressive.
Hi, I have a question. What disc and brakes you used ? SHimano, Avid, Hope, Magura ? Mechanical or hydraulic ? If hydraulic, what fluid ? DOT 5.1 or mineral oil ? 180 203 mm ? 2 mm thick ? What is stopping distance at 45 km per hour with full loaded ebike ?
The man, The Myth, The legend. your work impresses everytime. everything has a personal touch. Attention to detail is meticulous. I specially liked how you built the relay system for the lights. Would have never occurred to me. Thanks for another flawless build.
Haha, thank you so much! Kindly appreciated. Will most likely be using these lights for my build from now on, the light output is amazing for the price.
Respect Mate you are an artist. I wish I could afford to pay you to make me one. Iv'e watched a few Bafang builds yours is the most competent I have seen yet. Love the 3D printing and attention to detail you put in. NICE!
Thank you Donny! A full and comprehensive Video very Professional build!!30mph is enough for any fat bike!Very Enjoyable Viewing You really made that build 💯percent Neat and Tidy!👊👊👊🙏. 🤘😎🤘
Mannn you smashed with this insane build..... just PRO 🎉 Really good Build, just Amazing in any single detail ❤ Did you sell it afterthat?? Everyone must be happy with such a quality build❤
I believe 1200watts on bbs02 is its peak power but only when using 52v battery, 48v doesn't hit peak watts on 750w, i had a bbshd with 48v and its peak watts were a shy over 1000watts but when i use my 52v i can get up to 1500watts.
Was also wondering about a conversion , the only thing doing it after is always the cable management, always no matter how or you need to run additional cable runners or have a frame with inner tubing and lots of free space , nevertheless you did the out most best in not making it a ridiculous mess ... From what i can see these mid-engine do hang very low, did you had any problems clearing stuff with it ?
This is a great motor, so much torque. I have the same motor, but I changed the settings, so I get full power all the time when I'm on the throttle, but I put it on a hard tail 26x2.5 mountain bike and it eats hills for breakfast I would love it if I could make my own battery's 👍🏾
What was the beam pattern like. Many of these non-DOT approved headlights have high intensity artefacts in nearfield/foreground which reduces distance vision and wastes light.
your work is looking more and more professional .... if this was your favorite bike you should have gone with the 1500 w ..... your battery is really upgraded every time i see it .... i even like the bike myself .... good work .... 😉👍
How? There wasn't anything that was better than low end😂 not that it means anything bad. Just shows how nowadays even with cheap parts you can get good enough bike for many people
Your a beast mate, totally mental bike builds!!! Stupid question though does a wheel diameter help top speed, on a 15000-2kw hub motor, what size wheel would you recommend if i want to reach an easy 50-55kph,cheers bro😊
@@alitoroganan2442 It's still a standard size for hub motor kits. Also if I'm not mistaken, the larger the wheel, the more strain is applied to the motor for initial torque.
Great build! I don't understand why my 52V 1000W BBSHD is ... 1000W and your 750W BBS02B is 1200W ? In any case another video about the programming would be appreciated!
Thanks! You are not mistaken, the BBSHD is stated as 1000W and the BBS02B as 750W. I just wrote the actual power number that I get from this 750W motor which is over 1200W.
Your 52v bbshd will do more than 1000watts, check your display has a feature to show its power curve for watts, 500c or dpc-18 are good displays, i use 52v 20ah em3ev battery with my bbshd mines peaked at 1486watts so far.
I see thumbs up or thumbs down and don't know how to love a comment on here but sounds great... hope you stay n touch! You do amazing work & have great bike knowledge!! peace....@@DonnyTerek
О нет. Я купил аналогичный набор для аккумулятора. БМС не влезала, и я не догадался нагреть крышку. Вместо этого я сделал отверстия в корпусе для проводов, плату нацепил на корпус и накрыл крышкой. Крышку сделал на 3D принтере. 😢
@@DonnyTerek awesome! i am fairly new to 3d modeling and my tubes are very different then yours but want to adapt your model for my frame...but even if its a premade thing that might be great too!
Hi, replied about the battery mounts on the previous comment. If you're interested in getting a set made, please feel free to reach me at donnyterek@gmail.com . For the kick stand you mean the specialized stick at 44:40? 😄
✅🚵 Order your Himiway Cruiser here (£200 off UK Website!) - geni.us/0hxSC9n
1200 W at 91 % efficiency is 27 amps from battery. Do you think, that this thin nikel stripes can handle 27 amps in hot summer +38 *C all time till 47 V at battery terminals ?
I dont think you can't get more professional than this. Narration, layout, camera angle, sound... Everything is wonderful.
Yes, 2 temp sensors, and what will BMS do, if one of 70 cells get hot over 140 *C, SOC will be 100 % and thermal runaway will begin in midnight time, when people are in bed and near bed is ebike ? Ebike starts to produce H2, CO, CO2, HF, C2H2, CH4 etc. One spark and all house go to heaven.
😂😂😂😂@@PavolFilek😂😂😂😂
@@battedtomcatnlnl153 Please make PhD from chemistry. You will understand cathode and anodes, LiPF6, LFSI and understand conditions of TH. Bye.
I have built & bought several ebikes, currently rebuilding 2 that were damaged by flood waters from hurricane Ian in Florida and a new BBSHD fat bike build. Mechanically I can pretty much repair or replace anything on a bike, but that battery build blew me away. Very impressive.
Hi, I have a question. What disc and brakes you used ? SHimano, Avid, Hope, Magura ? Mechanical or hydraulic ? If hydraulic, what fluid ? DOT 5.1 or mineral oil ? 180 203 mm ? 2 mm thick ? What is stopping distance at 45 km per hour with full loaded ebike ?
The man, The Myth, The legend. your work impresses everytime. everything has a personal touch. Attention to detail is meticulous. I specially liked how you built the relay system for the lights. Would have never occurred to me. Thanks for another flawless build.
Haha, thank you so much! Kindly appreciated. Will most likely be using these lights for my build from now on, the light output is amazing for the price.
Yeah the whole build was impressive af, but the relay to turn on higher volt light section completely shocked me, that's what dedication looks like.
Wow. Impressive how you know all of this. Seeing the whole bike built from parts. But so many tools needed.
You did an amazing job with this bike. Your attention to detail is second to none.
What a lovely build. You did an amazing job. Nice work bro.
I am thoroughly impressed by how thorough you are. Nice build.
Respect Mate you are an artist. I wish I could afford to pay you to make me one. Iv'e watched a few Bafang builds yours is the most competent I have seen yet. Love the 3D printing and attention to detail you put in. NICE!
Thank you! Much appreciated. I will be putting my e-bikes for sale. If interested, feel free to reach me at donnyterek@gmail.com
Thank you Donny! A full and comprehensive Video very Professional build!!30mph is enough for any fat bike!Very Enjoyable Viewing You really made that build 💯percent Neat and Tidy!👊👊👊🙏.
🤘😎🤘
Thank you so much! Truly means a lot to me ✌
Clean build and very nice job on cable management. The 3D printed mounts and accessories are really trick.
Superb, meticulous, professional, adept, organised and entertaining, well done sir, well done.
Anyone know where I can get the 3d printed pieces for the attaching the brake lever sensors?
I just did the same except my bottle bolts were pulled loose after a car hit me from the side had to use rivnut gun and drill 1 out ! Top stuff !
Mannn you smashed with this insane build..... just PRO 🎉 Really good Build, just Amazing in any single detail ❤ Did you sell it afterthat?? Everyone must be happy with such a quality build❤
Really nice vid. well done!. What is the black glue you put on the wires connectors?
Great job 👍👍👍
Amazing build.🎉
Really clean.
I believe 1200watts on bbs02 is its peak power but only when using 52v battery, 48v doesn't hit peak watts on 750w, i had a bbshd with 48v and its peak watts were a shy over 1000watts but when i use my 52v i can get up to 1500watts.
Was also wondering about a conversion , the only thing doing it after is always the cable management, always no matter how or you need to run additional cable runners or have a frame with inner tubing and lots of free space , nevertheless you did the out most best in not making it a ridiculous mess ... From what i can see these mid-engine do hang very low, did you had any problems clearing stuff with it ?
You should add turn signals and a radio :)
This is a great motor, so much torque. I have the same motor, but I changed the settings, so I get full power all the time when I'm on the throttle, but I put it on a hard tail 26x2.5 mountain bike and it eats hills for breakfast I would love it if I could make my own battery's 👍🏾
Clever guy impressive work nice attention to detail. Cables look a bit messy but im OCD..
Thank you!
nice job...I like more your build version of the bike
do you build custom batteries for people? what price would it be? i would need 13s4p
What filament do you use for your prints? Any concern on the plastic warping when you place the DC converter in the sealed printed container?
Using PLA, no issues so far on a few of my e-bike builds. The DC converter does not produce much heat.
What was the beam pattern like. Many of these non-DOT approved headlights have high intensity artefacts in nearfield/foreground which reduces distance vision and wastes light.
your work is looking more and more professional .... if this was your favorite bike you should have gone with the 1500 w ..... your battery is really upgraded every time i see it .... i even like the bike myself .... good work .... 😉👍
Thank you so much! I kindly appreciate that you notice these details. Would love to try the BBSHD now. Hopefully a build with it is coming soon.
@@DonnyTerekthe bbshd is a beast, been using 2 of them for years, they take so much abuse and can be pushed to crazy levels of power.
I like it, Very nice build. What’s the material cost to build a 52v, 13ah battery?
Awaiting your next video for the review of the Bafang & the top speed, etc.
Coming soon.
Nice work!!!
Don't really like fatbikes but that really looks clean and fun.
Hello dear friend I thank you for your information on your ebike motor respect 😅
What size battery cells would you need for the bafang battery??
Does it run if when one battery is dead
mate, can you tell me where I can buy a cheap and reliable 20mh battery that delivers to the UK?
Very much yes!
can you do a video on how to make a rear rack battery pack please. that will be my next project to extend my battery range.
Hi, I am planning to make something similar in a few months.
Where can I buy wheels?
Really bro called us poor in all kinds of languages
How? There wasn't anything that was better than low end😂 not that it means anything bad. Just shows how nowadays even with cheap parts you can get good enough bike for many people
Which display is this?
Any fuses frightning
The BMS board acts as an adjustable fuse.
Your a beast mate, totally mental bike builds!!! Stupid question though does a wheel diameter help top speed, on a 15000-2kw hub motor, what size wheel would you recommend if i want to reach an easy 50-55kph,cheers bro😊
Thanks! Much appreciated. I'm not too sure but I would think that the wheel size wouldn't matter too much at top speed. I'd go for 26" though.
@@DonnyTerek any reason why 26
@@alitoroganan2442 It's still a standard size for hub motor kits. Also if I'm not mistaken, the larger the wheel, the more strain is applied to the motor for initial torque.
Great build! I don't understand why my 52V 1000W BBSHD is ... 1000W and your 750W BBS02B is 1200W ? In any case another video about the programming would be appreciated!
Thanks! You are not mistaken, the BBSHD is stated as 1000W and the BBS02B as 750W. I just wrote the actual power number that I get from this 750W motor which is over 1200W.
1200w on that bbs02 is the peak power but only if you use 52v battery
Your 52v bbshd will do more than 1000watts, check your display has a feature to show its power curve for watts, 500c or dpc-18 are good displays, i use 52v 20ah em3ev battery with my bbshd mines peaked at 1486watts so far.
Holy F, is that Vilnius? Yes it is!
all of the links to the battery cells don't work. Are you able to provide the battery cells that you used please.
Hi, please check if the links work now, thanks.
@@DonnyTerek unfortunately they still do not work.
@@97JoMiller Please check the nkon.nl link now. I guess others won't open because they are AliExpress and might not support your country.
the new JBD Wiring for their boards suck hard !
dziękuje za Twój film
Just to pass along, 26” fat tires are more like 29” in diameter. So your speed is probably off a bit
❤😂🎉😢😮😅😊. ไฟแอดพ์.
The battery build is an work of art🫡
were are you from ? are you dutch ? can you make me a battery ?
make engwe m20 part two
EKD01/B02N display is the best for me
Seems like a nice display too.
where are you live?
Bro got sponsored and and made a e bike good than the sponsored one
Do you sell bike?
This seems so far beyond me I am absolutely sure I would miss this up
40mph ebike is about perfect
Express that in MPH and we in the US will watch it.
bro its over 750W cops will hunt you down and drag to jail xD
cops only hunt trouble makers trust me!
No torque plates fir frame
Not needed for this kit.
have you ever shorted out battery @@DonnyTerek
Not that I remember, but the BMS has a short protection.
Nice
That is brilliant
Please learn how to solder properly.
Can I please hire you to convert my fat tire bike?
I would love to! But I'm afraid shipping would make most of the cost.
could always come to northern ontario for a weekend visit... I could make up an extra bed 4 U....! @@DonnyTerek
@@mikehowie8565 Thank you! Will keep that in mind!
I see thumbs up or thumbs down and don't know how to love a comment on here but sounds great... hope you stay n touch! You do amazing work & have great bike knowledge!! peace....@@DonnyTerek
Big Like !
О нет. Я купил аналогичный набор для аккумулятора. БМС не влезала, и я не догадался нагреть крышку. Вместо этого я сделал отверстия в корпусе для проводов, плату нацепил на корпус и накрыл крышкой. Крышку сделал на 3D принтере. 😢
8vegl muzkore klarinet😊0 4:25
Ohh.
[Applause]
Good for wild
you mean 15 mph bike ;) hahaha
All plug and play😂
I thought I know a lot about e bikes…
same 😂
Tjis isn't an "ebike".in the USA. You would need a tag for this motor vehicle. Brake light req. Turn signals req. Headlight req. etc etc ...
Same in Germany.
@@1337l4m3 It looks to me like a Boush 250watt is as fast as a Chinese - 500watt hub motor.
it is not building the E-bike, u just bought and assembled it and that's it! Change the title of the video🤬
yo where can i get those 3d printed spacers? Am i over looking them? i only need yours so i can edit them to fit my frame lol
Hi, sorry for the late reply. These are custom made, I am planning to have these for sale soon.
@@DonnyTerek awesome! i am fairly new to 3d modeling and my tubes are very different then yours but want to adapt your model for my frame...but even if its a premade thing that might be great too!
@@acedotcom I am able to customise the models to pretty much any size round tube frame if you can measure the tube diameter.
👍🚴🔋😍
i dont mean to sound rude but the two things I am looking for, your battery mount 3d prints and the kick stand :/
Hi, replied about the battery mounts on the previous comment. If you're interested in getting a set made, please feel free to reach me at donnyterek@gmail.com . For the kick stand you mean the specialized stick at 44:40? 😄