Ford 3000 tractor Simms Minimec dieselpump renovation
ฝัง
- เผยแพร่เมื่อ 19 ก.พ. 2022
- This tractor has not been able to start for some years. The problen was that no fuel was coming to the injectors. When I first looked at it, I dismantled the Simms pump a little while it was still on the tractor. I found the plungers totally stuck in the bores and freed them up. I cleaned the fuel tank and changed the two diesel filters. I then decided to take the pump off the tractor to get it resealed and make a video of the renovation.
- บันเทิง
Excellent video!!!
J.L.Kofod thank you
Brilliant, thank you, I have to overhaul mine tomorrow!
Simon Brooke thank you for commenting. Good luck with the overhaul.
@@poulgammelgaard8868 fortunately, before proceeding to the strip, I replaced a broken bleed screw, and the engine started. I think I'm going to put the injection pump strip off for a winter job, unless the hard starting problem returns.
Hello engineer Paul I am justice in ghana I over haul this pump twice a week .our problem is quality of plungers they brought here in ghana
Tak for den detaljerede video!
Hvor fik du den lille gummidims til den knap man trykker ind for at give ekstra brændstop under opstarten? Bruger den altid i koldt vejr, men gummiet er ødelagt.
Velbekom. Der sidder nok en næsten magen til på din Ford 5000.
injectionpumps.co.uk/product/simms-minimec-and-majormec-control-rod-bellows/
Thanks for the very clear and detailed video. Was just wondering what the behaviour of the pump should be when the timing marks are aligned? Trying to help out with the rebuild of a Ford which has a similar pump, though 6 cylinder, and when we have the marks lined up fuel still flows from the number 1 valve when trying the spill timing. When we supposedly line up all the timing marks the tractor still will not start and we are wondering if there is something wrong with the pump and we should remove it to look at getting it serviced.
thehermitish1 thank you for commenting. I would remove the top element and check it for stuck plungers and stuck delivery valves.
@@poulgammelgaard8868 thanks for the reply, I will pass the advise on to the owner. We are able to get the spill timing to engage but the timing mark on the plate is a good 60 degrees back from the mark on the casing. Regardless, something we will have to investigate further.
You will probably find your control rod or rack may be in the wrong position for spill timing.
Vaccum gov pumps are different to Mark 2 mech pumps like this and they are different to D-series Minimecs in adjusting the timing.
Plus you turn the engine in direction of rotation so that with the side door of the inj pump off you can see number one tappet lifting and what you want is the first of cutoff. Then replace the delivery valve, button it up, bleed it and I always pop the excess fuel
Button to bleed the air out faster than cranking it over with it off and she should fire up straight away..
I have the Ford 3000 with this Simms Injection pump. Sadly the Injection pump was already taken off when I got the tractor So I need to figure out where it was set as per timing marks at the pump. My middle plunger is stuck ( Soaking in Marvel mystery oil ) Now it's in CRC Evapo-Rust said to work great on rust ) So far I have not found a socket with the right splines either to remove the top section. I heard it's 34 teeth for Ford where Metric is 33 teeth. Pump did not have any or much oil in the right hand section....
Injectionpumps.co.uk have the special socket. If you watch my video at 42.55 you can see the timing marks under the little cover on the back end of the pump. With the ford 3000 on 19 degrees BTDC on the compression stroke it matches. You find the marks on the tractor flywheel behind a little cover on the bottom af the clutch housing. I find it easiest to rotate the engine, if I take off the starter motor and have acces to the teeth on the flywheel. To figure out if the tractor is on compression stroke, you maybe have to take off the valve cover.
Muy buen video master👏👏 , ¿para poder aumentar o reducir el caudal de petroleo que perno debo mover? Gracias
Thank you for commenting
I'd like to see what you went through for the timing of taking the fuel injection pump off the motor? I understand you got to be careful when you do that but it goes on exactly the same way?
When you bolt the gear back on the front of the pump, the bolt holes are slotted, so you can not be sure where it is correct. Before taking the pump off, you have to turn the tractor to 19 deg btdc on the compression stroke. There is a little plate to take off on bottom of the clutch housing where you can read the 19 deg on the flywheel. On the pump there are timing marks on both ends, as I show in the video.
Great video, thanks for sharing your knowledge, i need to fix mine, but i can not find the kit, where can i get it?, tia!!
Luis Calderon thank you for commenting. You will also need the special socket for the valve holders. Injectionpumps.co.uk have it.
Nice video,can you tell me please where did you buy the gasket kit and additional parts?
jose m mora b thank you for commenting. You will also need the special socket for the valve holders. Injectionpumps.co.uk have it.
@@poulgammelgaard8868 Thank you very much!
What is the name of the tool used to remove that stuck cover with an impact wrench? It has a center punch and pry grippers. Thanks.
Puller with three adjustable arms
@@poulgammelgaard8868 thanks, that was very helpful!
I’m rebuilding this pump and I need the special spline socket that you are using, can you please tell me where I can get one. Thank you so much
I bought mine from "injectionpumps.co.uk", it was out of stock many other places, where I looked for it.
@@poulgammelgaard8868 thank you!
Hvilken olie skal der på pumpen efter reparation/service?
Jeg brugte bare alm 15 w 40, samme olie som motoren.
Hej hvor har du bestilt reservedele fra?
Hej Kristian. Det meste er fra injectionpumps.co.uk, de har bl.a. den specielle top til ventilholderne. en anden mulighed er: www.charnleys.com/part/leyland_middle/17h6606/fuel-valve-and-guide
Mvh Poul
Need a replacement plunger for simms injection pump off of a 1968 ford 3000 the lever that the rail turns on plunger is broken. Any suggestions? Thanks
Injectionpumps.co.uk have the parts you need: Simms Minimec delivery valve removal splined socket. ID: F14A, seal kit for Simms Minimec 3 cylinder diesel injection pumps: ID S13, plunger and element for Simms Minimec pumps 512506-42, ID M6A.
@@poulgammelgaard8868 Thank you so much
Should all three be replaced or can the one that's broke be replaced only?
You can replace just one, but I would replace all three, but after replacing one or more the pump needs to be calibrated. You could alternatively just transfer the lever from a new plunger to the old plunger if you have a hydraulic press. It has to be oriented exactly the same in order to get the calibration right.
@@poulgammelgaard8868 Thanks again for your help sir.
Where did you order the plunger in element from?
injectionpumps.co.uk, You will also need the special socket for the valve holders
Hey I also have the same pump in my ford 3000 but the condition of my pump is ruff 😅 can you find me or source me another same pump if possible.I live in India there are only 10 tractor with same pump in India which are imported from England at that time and it’s impossible to arrange that same pump here. So can you help me to arrange that pump. I am waiting for your reply 🙏