I recommend using painters tape before you remove the original emblems to line off the edges to help with putting the new ones on perfectly level in the exact same spot.
Very well explained --- THANKS. I almost didn't try this because of the challenges you had getting the rubber trim popped back out after putting the 6 inch painted trim piece (that the "H" symbol is connected to) back on. You used your plastic trim "pop off too"l to pry the rubber trim back out -- but you had what looked like a pretty tough challenge getting it back out of the seam. Instead of using your approach, I put a strip of painters tap -- glue side facing up -- over the rubber trim. Then put another strip of painters tape, covering 1/2 the width of the previous strip of tape (just to make the painters tape wider than I strip would provide), and then to pull the tape away from the work area, I put some small pieces of tape running straight up, onto the back window, to pull my strips of tape up and away. Once I got the 6" plastic trim piece snapped back onto the car, I just pulled the painters tape off the rubber trim, and it fell right back into place without being squeezed into the gap that you were struggling to get the rubber trim out of. Everything else worked great, just like you showed. Thanks again.
Very well explained and looks great! I painted the emblem black on my 2016 crv without removing the trim just slowly pulling it out, luckily the washers fell out where the license plate lights are but this looks much more professional.
After removing the emblems with floss you know it's much easier to just heat the remaining foam lightly with the heat gun and it would come off a lot easier vs. trying to manually roll it off with your fingers.
Yes. But it's not going to less lol. I made it permanent. It will less for years. I was looking just to get dipped too but it's only less max 2 years or so. Paint will fade too. Car washes will pill it of slowly.
Great video, but one important thing that you should do is make a template of the emblem prior to removal so you know exactly where to put it back instead of just eyeballing it like you did. Adjust horizontal position of the emblems as well with leveler tool while you were making a template coz sometime they are crooked straight from the factory.
@@IvanRossS Put masking tape around the emblem strategically from the taillights vertically and horizontally so you know exactly where the C starts or where the V Stops. Remove the masking tape before you do the removal or emblems and clean up, then lay the masking tape back on the trunk again so you now know exactly where to put the emblem back. Align the emblem horizontally by using a leveler and make adjustments if required. Emblems always appear crooked when it’s not aligned horizontally.
My goodness, what a pain for just swap little plastic letter. My Honda Passport is just pull the emblem of with plastic lever, clean the spot then push new one in.
I definitely agree with a pain in the butt but there is a way to get around it. By just simply pulling out and breaking H logo.. and replacing it with a new one But you have a chance to ruin some things. Put scratches on pain. And I believe 3M double tape not really going to hold it properly being so thin on the back of the new logo
Just plasti-dipped mine after seeing the pdf instructions on Honda site. Sport model has blacked out “sport badge” it should have the others blacked out from the factory
Dude im pretty sure you didnt have to take off the whole inside of your car and just used floss around the emblem, pop it off and put black one in its place. Ive never see someone pop off the whole inside of there car
You don't have to. You can Ridgid pretty much everything. And do a half ass job I show it how it needs to be done by the book... you can find these manuals all over Honda website... and this is proper way !
Also you probably have not noticed or you didn't finish watching the whole video but Honda emblem holds by two metal washers from the inside and those are really hard to remove.... to proper secure it have to be be the same way installing emblem and securing with two little washers from the inside.... emblem is really thin and just 3M tape is not going to hold it after a couple of pressure washers it will fall off
@@IvanRossSvery true, im just gona have the dealership do it bc i dont feel confident in taking the door apart. I would probably break the pegs off trying to take the emblem off anyway. Appreciate the video
Just put my black H emblem on my brand new pilot black edition yesterday, looks great , Honda should do that at the factory for black edition , by the way Слава Україні🇺🇦
how did you do it? we just got the '23 pilot trailsport. wanting to replace the chrome H mark with a gloss black one. do i need to open the inside of the trunk or i can pry the emblem directly?
Дякую за відео! Перший канал де багато корисного матеріала безпосередньо від власника Honda CR-V hybrid! Так легко у Вас все виходить), таке враження, що мали досвід в автосфері. Рамка під номерний знак - ТОП! Слава Україні! Слава ЗСУ!
Hey Ivan, just wondering if you check your CRV underbody? I know that Toyota has the thing called under body plug (under about in passenger and driver under body) that is part of PDI inspection to plug it in. Reason I asked is because mine didn't get installed and just wondering if you can look up yours and to see if you have the body plug installed? Thank you beforehand!
Double tape was made by 3M. You can buy it at any hardware store And blue paint was simply nail polish... yes I know it's not a great choice lol. Because it's going to be on direct sun but we'll see how long it's going to last. But you can buy any enamel base blue paint. You can find a little small jars of this type of paint at the craft stores. For only few dollars
@@NinjaAlex6r I was thinking about it. I'm sure soon it will be sticker available that you can just put over it. It shouldn't mess with a radar. but over all that logo been chrome don't look to bad
@@IvanRossS Я на Copart купив теж Хонду Спорт з невеликим пошкодженням. Зараз пливе, очікую і потроху вивчаю що може бути корисним... Буде перший мій гібрид)
Buddy barely got his car and he’s already modifying it!!! I respect that! 🤝
Yep that how you do it lol. I modified all my cars and updated audio system, brakes etc. on my old RAV4 i had.
@@IvanRossS haven't even picked up my new CRV yet, and already ordering stuff for it 🍻👍
I recommend using painters tape before you remove the original emblems to line off the edges to help with putting the new ones on perfectly level in the exact same spot.
that's what the 2 pegs are for
@@nbraa only the H has the pegs
Very well explained --- THANKS. I almost didn't try this because of the challenges you had getting the rubber trim popped back out after putting the 6 inch painted trim piece (that the "H" symbol is connected to) back on. You used your plastic trim "pop off too"l to pry the rubber trim back out -- but you had what looked like a pretty tough challenge getting it back out of the seam. Instead of using your approach, I put a strip of painters tap -- glue side facing up -- over the rubber trim. Then put another strip of painters tape, covering 1/2 the width of the previous strip of tape (just to make the painters tape wider than I strip would provide), and then to pull the tape away from the work area, I put some small pieces of tape running straight up, onto the back window, to pull my strips of tape up and away. Once I got the 6" plastic trim piece snapped back onto the car, I just pulled the painters tape off the rubber trim, and it fell right back into place without being squeezed into the gap that you were struggling to get the rubber trim out of. Everything else worked great, just like you showed. Thanks again.
That rubber seal was the worst part about whole job
Good idea!
What a great, helpful, to-the-point, quality video. Thank you! This is exactly what I’ve been looking for.
Great video and very clear instructions. Install went flawless and had no issues whatsoever thanks to you!
Great to help, now you have quality made logos that will last you for years and you never have to repaint
Very well explained and looks great! I painted the emblem black on my 2016 crv without removing the trim just slowly pulling it out, luckily the washers fell out where the license plate lights are but this looks much more professional.
After removing the emblems with floss you know it's much easier to just heat the remaining foam lightly with the heat gun and it would come off a lot easier vs. trying to manually roll it off with your fingers.
Looks great!!! Thanks for sharing the how too.
Wow thanks. It’s actually not as hard as you would think. The process is a little tedious but it’s doable
Great video, Thanks!
Just ordered mine. Thinking about ripping and gluing the new one 🤔
I heard people do that :)
Where did you buy it from brother?
I just plastidip it black, works beautifully! Just took less than half an hour when and make sure your car is clean, that is it!
Yes. But it's not going to less lol. I made it permanent. It will less for years. I was looking just to get dipped too but it's only less max 2 years or so. Paint will fade too. Car washes will pill it of slowly.
@@IvanRossS True, it only last maybe 3-4 years. If you hand wash your car it may last 5-6 years. How much you buy the blackened emblem btw?
@@slothypunk all links in the discretion. And currently prices. I bought a kit
@@IvanRossS Thank you, I don't realize it in the description below
Looks so much better.
Wow quite a bit of a pain! Good job.
It was worth it :) I have not seen any CRV with blacked out emblems yet
Great video, but one important thing that you should do is make a template of the emblem prior to removal so you know exactly where to put it back instead of just eyeballing it like you did.
Adjust horizontal position of the emblems as well with leveler tool while you were making a template coz sometime they are crooked straight from the factory.
Couldn't because area was buffet and polished
@@IvanRossS Put masking tape around the emblem strategically from the taillights vertically and horizontally so you know exactly where the C starts or where the V Stops. Remove the masking tape before you do the removal or emblems and clean up, then lay the masking tape back on the trunk again so you now know exactly where to put the emblem back. Align the emblem horizontally by using a leveler and make adjustments if required. Emblems always appear crooked when it’s not aligned horizontally.
My goodness, what a pain for just swap little plastic letter. My Honda Passport is just pull the emblem of with plastic lever, clean the spot then push new one in.
I definitely agree with a pain in the butt but there is a way to get around it. By just simply pulling out and breaking H logo.. and replacing it with a new one But you have a chance to ruin some things. Put scratches on pain. And I believe 3M double tape not really going to hold it properly being so thin on the back of the new logo
Just plasti-dipped mine after seeing the pdf instructions on Honda site. Sport model has blacked out “sport badge” it should have the others blacked out from the factory
Yeah I know. That's alot of work
Topgun modification video on the Topgun SUV.
❤️ 🇺🇦
🇨🇦
What's crazy to me is there's a world in which people live that want Chrome emblems. I don't understand that at all.
Great job. I have to say though that it is ridiculous Honda makes it that hard to simply change the emblem.
Yes I was surprised too.. but just wanted to do it properly by the book and shoot a video about it
@@IvanRossS and that…you did.
Nice job! But "Hybrid" emblem was placed slightly slanted downward on the right side.
No it's not it's just look like this the video
Ну красавчик 😍 за символику 🇺🇦 отдельный респект 👍
Are the new emblems gloss black and the SPORT satin? Do they match?
Excellent how to video. Thank you for doing it.
One question, Is that blue nail polish you used to fill the letters in?
Yes it was nail polish lol. So far it's holding up.
Thank you for the quick reply Ivan. That's what I'm going to use also. Pretty cheap to buy to. Less than $2.00 here in USA.@@IvanRossS
@@bigallis1 I'm in US too :)
Amazing video! Would you like to test our new product glossy black front garnish overlays?
Dude im pretty sure you didnt have to take off the whole inside of your car and just used floss around the emblem, pop it off and put black one in its place. Ive never see someone pop off the whole inside of there car
You don't have to. You can Ridgid pretty much everything. And do a half ass job I show it how it needs to be done by the book... you can find these manuals all over Honda website... and this is proper way !
Also you probably have not noticed or you didn't finish watching the whole video but Honda emblem holds by two metal washers from the inside and those are really hard to remove.... to proper secure it have to be be the same way installing emblem and securing with two little washers from the inside.... emblem is really thin and just 3M tape is not going to hold it after a couple of pressure washers it will fall off
@@IvanRossSvery true, im just gona have the dealership do it bc i dont feel confident in taking the door apart. I would probably break the pegs off trying to take the emblem off anyway. Appreciate the video
Excellent video! Thank you! 🇺🇦 🇺🇦
What is the stuff you used to take out the minor scratches you said?? After you used the winded?
Just put my black H emblem on my brand new pilot black edition yesterday, looks great , Honda should do that at the factory for black edition , by the way Слава Україні🇺🇦
On sport touring with all that money they charged.. it should comes with it
how did you do it? we just got the '23 pilot trailsport. wanting to replace the chrome H mark with a gloss black one. do i need to open the inside of the trunk or i can pry the emblem directly?
@@12Jsilva Hi ,it should come out pretty easy , you just have to cut of 3M tape on the top and bottom by using fishing line
@@MultiFays gotcha. Will do it tomorrow. Got my emblem today 😁😁😁
Good luck
Дякую за відео! Перший канал де багато корисного матеріала безпосередньо від власника Honda CR-V hybrid! Так легко у Вас все виходить), таке враження, що мали досвід в автосфері.
Рамка під номерний знак - ТОП! Слава Україні! Слава ЗСУ!
Дyже дякую вам. Героям Слава 🇺🇦
You make it look so easy to do🤣!
I know that was a ridiculous job but I was just trying to show people by the book how is done properly. Besides painting hybrid logo :)
@@IvanRossS i wanna do it but I’m scared of messing up
That middle one seems like such a pain, i don’t get why they didn’t have it glued on like the other ones.
I was surprised to find out how much work need to be done when I ordered these emblems. But it was a great opportunity for a video 😀
RearGate Insulation: pls post video! TY
OH MAN...i cant do that to my new car. hahaha... i wish it was easier
It's yours you can do whatever you want with it
How much did you cost for all?
What the tool name you use to heat the bubble
That’s a lot of work the silver emblem is ok me personally I wouldn’t do that
It is. But I did it properly. By the book. I have heard people yanked it out. By braking it off and just gluing new one back on.
What about the H for the grill?
@@michaelfiss4282 they don't have it because it's your front radar sensor
Do you think its possible to access the H logo from the trunk handle below it?
No lol. Of course not. You have to do all this job just to get to it . I know it's insane. But it's can be done as u see on the video
Hey Ivan, just wondering if you check your CRV underbody? I know that Toyota has the thing called under body plug (under about in passenger and driver under body) that is part of PDI inspection to plug it in. Reason I asked is because mine didn't get installed and just wondering if you can look up yours and to see if you have the body plug installed? Thank you beforehand!
I’m curious tho! What’s the reason for the insulation!?!
What do you mean what is the reason for insulation? You installing insulation to lower outside noise lol.
Give me the name of the blue that you painted the hybrid and the adhesive tape, please!!!
Double tape was made by 3M. You can buy it at any hardware store And blue paint was simply nail polish... yes I know it's not a great choice lol. Because it's going to be on direct sun but we'll see how long it's going to last. But you can buy any enamel base blue paint. You can find a little small jars of this type of paint at the craft stores. For only few dollars
Do you have Honda part# for the H and CR-V black emblems?? How about the front one??
@@toddmeadows1291 You probably have these, but maybe it will help someone else. The H and CR-V kit part #: 08F20-3A0-100
I wish someone could do a 2023 pilot emblem install???? PLEASEEEEE
wanting to replace mine on my 23 trailsport. dunno why the badges are black but the H emblem is chrome
Can u send me the link for buy the black one , please 😅
Read description...
Can you list the black and blue paint that you used?
Black paint you can literally see in the video. Blue paint was nail polish
What type of blue was it? It was hard to see the name, also did you use the gorilla glue to stick back the hybrid logo? Thanks for the response
Where u got the crv logo? I can’t find in us
You never read descriptions to the videos..... you can find a lot of useful information in that section ! all links in the description
Дякую!
Будь ласка :)
Have you blackout the front fake air vents yet
I just ordered those to replace mine.
Garnish L Front Bumper 71157-3D4-A01
Garnish R Front Bumper 71152-3D4-A01
No. actually do not find them being ugly at all.
More video trik for the crv hybrid
Do you plan on doing the front emblem?
You can't lol. Its a radar
😩😩 you think we can smoke it with light tint vinyl?
@@NinjaAlex6r I was thinking about it. I'm sure soon it will be sticker available that you can just put over it. It shouldn't mess with a radar. but over all that logo been chrome don't look to bad
@@IvanRossS I bought dark smoked vinyl and it had no effect on the radar system
hi is there emblem for the front?
No, front emblem it's a radar. Very very expensive peace
How about a spare?
No spare tire in Hybrid models
The blue shade looks cheap, you shouldve pick a better blue gloss shade so it will look better
It's same color lol on all Hybrid logos
Id just rip it off and adhere the new one.
Can you putting to my crv?
Yes sure. send me your address, I can go ahead take a vacation buy plane ticket, pay for it and fly to you to install Honda logo
Thank you for supporting Ukraine!❤
I was born and raised in Ukraine of course I will support Ukraine
@@IvanRossS Тоді це все пояснює) Приємно чути)
@@IvanRossS Я на Copart купив теж Хонду Спорт з невеликим пошкодженням. Зараз пливе, очікую і потроху вивчаю що може бути корисним... Буде перший мій гібрид)
Why the fuck would anyone pay for and install a black auto logo.
Слава Україні!
Героям слава, смерть ворогам ✊️🇺🇦
Whyyyy
Why what lol??