Remember to turn off phase filter function in VESC Tool if you have newer version! As it was not made clear in the video! (Phase filer is not available for Flipsky ESC75100 and 75200! Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in escs damage. Please do not restore the default parameters when using the wizard interface.)
Thanks for the reminder, since we are using firmware 5.2 in the video, it is not marked as such. I have noted your suggestion in our profile column. Thank you for your rigor, which has brought convenience to other viewers.
Hi i have 2 Quastions. Iwant to use it for a kide Ride On car. 1. Can I also use it for brushed motors? 2. Is there an option to use a normal 3 pin throttle? Thanks in common
Why not use the UART communication with the remote? Because on Uart it gives all data (amperage, temperature, and battery) on the remote, while via ppm it doesn’t show anything.
how did you get it to work? I am connected via Uart, but I don’t get amperage, nor temperature nor voltage. Do I have to change some settings in the VESC tool?
Hello, Is it normal that the battery, current and power info is missing ? I connected my vx3 remote in uart with the 8pin connector. In my previous "Flipsky high-current FSESC 200A 60V" I had all the informations.
Hello, sir. Thanks for your message. Sorry for any inconvenience caused. Please let us know your question through email at flipsky-service@outlook.com/fs_service@flipsky.net
where does the blue wire from the receiver go?...the diagram shows it goes to the positive line from the battery...for a 12s battery that means 50v to the blue wire to the receiver?
The blue dupont wire is for eskate board or efoil battery signal notification. Soldering it with battery + and adding glue for insulation please. Thanks.
Señor, si está utilizando FSESC 75200 con carcasa de refrigeración por agua, debe utilizar un conector de bala de 8 mm. Enlace: flipsky.net/collections/connectors/products/bullet-connector?variant=42844026503409
У меня контроллер 75300 и мотор 65161 Батарея 20s не могу сделать калибровку двигателя ругается на отсутствие датчиков хола На батарее 13s все проходит без проблем
Здравствуйте, сэр, какое сообщение об ошибке появляется при использовании 20S для настройки параметров? Это перенапряжение? Какую версию прошивки вы используете?
Ошибка по напряжею возникает в версии 6.+ именно это натолкнуло меня на мысль попробовать сделать напряжение по меньше Но я сейчас работаю в версии 5.2 так как рекомендована на сайте производителя контроллера
@@ИванВикторович-з2д Здравствуйте, сэр, так как настройка входного напряжения по умолчанию составляет 72 В, когда мы покидаем завод, при использовании батареи 20S вам необходимо изменить значение максимального входного напряжения. Изменено положение: General-Advanced-Maximum Input Voltage (батарея 20S должна быть изменена на 90V)-↓M (напишите для сохранения). Поскольку TH-cam не может отправлять изображения, если вы не можете найти измененное местоположение, вы можете отправить электронное письмо в наш отдел послепродажного обслуживания: flipsky-service@outlook.com
@@FlipskyTech при изменении этого параметра на 90 v выскакивает окно The following parameters were truncated because they were set outside of their allowed limits.
Remember to turn off phase filter function in VESC Tool if you have newer version! As it was not made clear in the video!
(Phase filer is not available for Flipsky ESC75100 and 75200!
Please turn off the phase filter function and choose "false" in vesc_tool when use firmware version on or above 5.3 (VESC_TOOL 3.01). Without turning off the phase filter will result in escs damage. Please do not restore the default parameters when using the wizard interface.)
Community is crucial!
Thanks for the reminder, since we are using firmware 5.2 in the video, it is not marked as such. I have noted your suggestion in our profile column. Thank you for your rigor, which has brought convenience to other viewers.
The FSESC75200 is so compact ... Good job !
Glad you like it, thank you so much.
Hi i have 2 Quastions. Iwant to use it for a kide Ride On car.
1. Can I also use it for brushed motors?
2. Is there an option to use a normal 3 pin throttle?
Thanks in common
Hi. The ESC is not suitable for brushed motors. And about question 2 do you ask the 3 pin throttle whether connects with ESC?
Why not use the UART communication with the remote? Because on Uart it gives all data (amperage, temperature, and battery) on the remote, while via ppm it doesn’t show anything.
Thanks for suggestion.
how did you get it to work? I am connected via Uart, but I don’t get amperage, nor temperature nor voltage. Do I have to change some settings in the VESC tool?
What battery voltage was used in this demo?
It's 12S battery.
Hello,
Is it normal that the battery, current and power info is missing ? I connected my vx3 remote in uart with the 8pin connector. In my previous "Flipsky high-current FSESC 200A 60V" I had all the informations.
Hello, sir. Thanks for your message. Sorry for any inconvenience caused. Please let us know your question through email at flipsky-service@outlook.com/fs_service@flipsky.net
Did you get it to show up again? I have the same issue…
where does the blue wire from the receiver go?...the diagram shows it goes to the positive line from the battery...for a 12s battery that means 50v to the blue wire to the receiver?
The blue dupont wire is for eskate board or efoil battery signal notification. Soldering it with battery + and adding glue for insulation please. Thanks.
Hola, necesito saber los conectores que lleva el control con el motor,, yo tengo el mismo controlador
Señor, si está utilizando FSESC 75200 con carcasa de refrigeración por agua, debe utilizar un conector de bala de 8 mm.
Enlace: flipsky.net/collections/connectors/products/bullet-connector?variant=42844026503409
Fsecs 75200, 75350 очень нуждается в ip 67. Это же водные виды спорта .
What are some good batteries i can use?
Sorry friend, we don't sell batteries so no good idea🥲
@@FlipskyTech how many volts and ah should the battery be and what battery was used in this video?
Also what i am trying to build is my own diy seabob f5 which is an underwater scooter.
@@ramaanplayz2901 FSESC75200 voltage safe for 4-20S and in video we use 12S.
@@ramaanplayz2901 Oh, looking forward your great build for diy seabob f5👏
Is there a gps in the remote?
Yes, the remote can display GPS
У меня контроллер 75300 и мотор 65161
Батарея 20s не могу сделать калибровку двигателя ругается на отсутствие датчиков хола
На батарее 13s все проходит без проблем
Здравствуйте, сэр, какое сообщение об ошибке появляется при использовании 20S для настройки параметров? Это перенапряжение? Какую версию прошивки вы используете?
Detection failed. Reason: Sensor detection failed
V5.2
Ошибка по напряжею возникает в версии 6.+ именно это натолкнуло меня на мысль попробовать сделать напряжение по меньше
Но я сейчас работаю в версии 5.2 так как рекомендована на сайте производителя контроллера
@@ИванВикторович-з2д Здравствуйте, сэр, так как настройка входного напряжения по умолчанию составляет 72 В, когда мы покидаем завод, при использовании батареи 20S вам необходимо изменить значение максимального входного напряжения.
Изменено положение: General-Advanced-Maximum Input Voltage (батарея 20S должна быть изменена на 90V)-↓M (напишите для сохранения).
Поскольку TH-cam не может отправлять изображения, если вы не можете найти измененное местоположение, вы можете отправить электронное письмо в наш отдел послепродажного обслуживания: flipsky-service@outlook.com
@@FlipskyTech при изменении этого параметра на 90 v выскакивает окно
The following parameters were truncated because they were set outside of their allowed limits.