How to remove old wallpaper glue with out chemicals once the wallpaper has been removed

แชร์
ฝัง
  • เผยแพร่เมื่อ 20 ต.ค. 2024
  • How to remove old wallpaper glue with out chemicals once the wallpaper has been removed

ความคิดเห็น • 72

  • @bhappy8892
    @bhappy8892 2 ปีที่แล้ว +4

    I used this process, went over couple times, the walls are squeaky clean. Ready to paint. Thank you for sharing this video. God bless.

    • @nitrokyosho
      @nitrokyosho  2 ปีที่แล้ว +1

      Glad to help friend

  • @BeverlySwegman
    @BeverlySwegman 3 ปีที่แล้ว +7

    Thank you so much, I did what you said to remove my old wallpaper on my plaster wall. Worked great!

    • @nitrokyosho
      @nitrokyosho  3 ปีที่แล้ว

      Thank you glad to hear

  • @jonathanbecker9082
    @jonathanbecker9082 3 ปีที่แล้ว +6

    Thank you for this video!!! Who knew??? You wouldn’t believe how long I’ve been putting this off!!!

    • @nitrokyosho
      @nitrokyosho  3 ปีที่แล้ว +2

      Glad to help my friend

  • @michaelbedell6523
    @michaelbedell6523 2 ปีที่แล้ว +2

    Great video for a simple approach. Am sure your next video will suggest to prime the walls to seal any glue residues. Thanks again

  • @jess6972
    @jess6972 ปีที่แล้ว +1

    Pretty much. I do a quick wipe wet it with water and a little dish soap really helps break that glue down. Then wipe with clean water and dry towel gets all that glue off. Then either good primer+paint or primer then paint. House i bought lady looooved wall paper lol

  • @LoathsomeX
    @LoathsomeX ปีที่แล้ว +1

    thank you so much. good vid and no bs. greetings from finland.

  • @F-MK96
    @F-MK96 4 ปีที่แล้ว +3

    Thank you so much I am planing to paint over the wall so is there another step to paint over it or once i take the glue off in this manner i can just go ahead fill up the holes and paint?

    • @nitrokyosho
      @nitrokyosho  4 ปีที่แล้ว

      Yes after the glue is off check the wall and patch any defects ,I use a plastic putty knife and spackle pre mixed from a hardware store

  • @drinny26
    @drinny26 3 ปีที่แล้ว +2

    I took the paper down and the glue is dry as can be. Not tacky at all. Should I still remove the glue or can I get a good primer from Kills and just prime it?

    • @nitrokyosho
      @nitrokyosho  3 ปีที่แล้ว +3

      Yes I would take a hot bucket of water and a sponge and wipe the glue off if you don't it could have a chemical reaction with the paint not adhering properly. It's quick and easy to do.just wipe the walls with a sponge and hot water.

  • @krystalblackburn6471
    @krystalblackburn6471 2 ปีที่แล้ว +1

    Thank you for the video!
    Hopefully an easy quick question. When can one sleep in the room after the wallpaper has been removed and the walls have been wiped down? Do you have to prime it first?

    • @nitrokyosho
      @nitrokyosho  2 ปีที่แล้ว

      You can sleep in the room immediately there's no health hazard danger, I use water based kilz primer low odor I slept in the room after painting same day. I Also use behr paint water based low odor.

    • @krystalblackburn6471
      @krystalblackburn6471 2 ปีที่แล้ว

      @@nitrokyosho Thank you!

  • @jamesgulla9125
    @jamesgulla9125 3 ปีที่แล้ว +2

    Hey Ray, thank you for the video and the information. it is very helpful.

  • @M4R1N4
    @M4R1N4 2 ปีที่แล้ว +1

    You never made the follow-up? I didn't find it anyway.. my bathroom wallpaper was from the 60s and I believe was put up with paste. Hot water doesn't seem to dissolve it easily like you are doing here. Do I need a different tactic or just keep at it again with hot water? Thanks!!

    • @nitrokyosho
      @nitrokyosho  2 ปีที่แล้ว +1

      You can try a steamer there pretty cheap $50.00 at home depot that will be stronger than a sponge and hot water.

  • @lakishasnipes5680
    @lakishasnipes5680 9 หลายเดือนก่อน +1

    What is the next step to do before painting ??this video helped me alot i feel like my glue has been a struggle

    • @nitrokyosho
      @nitrokyosho  9 หลายเดือนก่อน

      I like to use kilz stain blocker primer water based before painting also I use a pre mix dap spackle to fix any wall imperfections can be applied with a putty knife.

  • @cynthiamolina1557
    @cynthiamolina1557 2 ปีที่แล้ว +2

    Hi, thank you for the video. I'd seen another video similar to yours where the person used a wet sponge and I started doing it with that. The paper doesn't come off as easily a it did in your video or theirs. It almost shredded when I did it. I know it could be my technique, but could it be due to how they applied the paper? Could it be because I didn't use hot water?

    • @nitrokyosho
      @nitrokyosho  2 ปีที่แล้ว

      Yes you need to use hot water

    • @bhappy8892
      @bhappy8892 2 ปีที่แล้ว +1

      After wetting the paper, let it soak for 10/20 mins before peeling it off. I personally soak the entire wall at a time, while one wall is soaking I go back to the previous wall and remove the paper. Believe me the whole row will come of in one pull, just like cutting softened butter☺️. You have to be patient. Try it and let me know if it worked for you. You may have some tiny pieces in the corners that might need a plastic spatula to loosen it out.

  • @blairsomberg9391
    @blairsomberg9391 4 ปีที่แล้ว +2

    LOVE LOVE LOVE your videos Thank you!!!!

    • @nitrokyosho
      @nitrokyosho  4 ปีที่แล้ว

      Thank you buddy and thanks for watching

  • @cyhomer
    @cyhomer 10 หลายเดือนก่อน

    Hi..I need help! I have just removed some VERY old paper…but I have a lot of old, yellow, hardened glue left over. I don’t think your water will do a thing. Any better ideas? Ty!

    • @nitrokyosho
      @nitrokyosho  10 หลายเดือนก่อน

      Get a steam machine there cheap at home depot $60.00 the steam will melt the glue then wipe it Wagner 725 Wallpaper Steamer 2418627 - The Home Depot
      www.homedepot.com/p/Wagner-725-Wallpaper-Steamer-2418627/316606367

  • @ftocar
    @ftocar 2 ปีที่แล้ว +1

    Once you’ve washed the wall and got the glue off is it okay to paint afterwards

  • @TheBeesKneesPhoto
    @TheBeesKneesPhoto 3 ปีที่แล้ว +2

    Will this work if the wall was never painted underneath and it's basically untreated sheetrock?

    • @nitrokyosho
      @nitrokyosho  3 ปีที่แล้ว +2

      Yes the demo I'm doing it on is a wall that was never painted

  • @mikeweissenborn6055
    @mikeweissenborn6055 3 ปีที่แล้ว +1

    Watched your vid, hoping for some short-cuts as I have about 60ft of wall to prep. Major issue I am having is at many doorways plastic corners were applied with contact cement to protect the wallpaper edges. How do I remove this OLD contact cement stuck on walls to paint over?

    • @nitrokyosho
      @nitrokyosho  3 ปีที่แล้ว

      I would try to sand it down to get rid of it

  • @BDSxPIPESTAND
    @BDSxPIPESTAND 3 ปีที่แล้ว

    What type of primer would you use for this oil base or just standard?

    • @nitrokyosho
      @nitrokyosho  3 ปีที่แล้ว +1

      I use Kilz white stain blocker paint water based, no one uses oil based any more in home's

  • @thomasmoore1823
    @thomasmoore1823 3 ปีที่แล้ว +5

    What is the ratio of vinegar to water?

    • @bhappy8892
      @bhappy8892 2 ปีที่แล้ว +1

      He’s only using HOT water, no vinegar.

  • @HighFlyBlue
    @HighFlyBlue 2 ปีที่แล้ว

    Is there anything different to do if I have a wall that had wallpaper but was painted before the glue residue was taken off? I have a small bathroom I want to repaint but you can see glue residue under the current paint.

    • @nitrokyosho
      @nitrokyosho  2 ปีที่แล้ว +1

      The only way to fix that is to sand the walls smooth

  • @Ne14tns
    @Ne14tns 2 ปีที่แล้ว

    Does this washing process work on dry wall, or will this ruin the wall?

    • @nitrokyosho
      @nitrokyosho  2 ปีที่แล้ว

      This video is being done on dry wall

  • @nevilleroberts2805
    @nevilleroberts2805 3 ปีที่แล้ว

    Hi sir thanks for the video but what’s the name to that sponge?

  • @Stamnessj
    @Stamnessj 3 ปีที่แล้ว +1

    Is the process the same for a chipboard wall? I'm afraid the glue inside the chipboard will disolve!

    • @nitrokyosho
      @nitrokyosho  3 ปีที่แล้ว

      I would give it a try

  • @samlightner
    @samlightner 4 ปีที่แล้ว +7

    please i need to know the next step make another video!!!!

  • @KatsBeautyBlog
    @KatsBeautyBlog 4 ปีที่แล้ว +2

    Thank you for the help :)

  • @ericaortiz03
    @ericaortiz03 2 ปีที่แล้ว +1

    Will this work on wood?

  • @skokie8231
    @skokie8231 ปีที่แล้ว +1

    I have so much hard glue all over the wall. It's just not coming off even with a putty knife. Any ideas?

    • @nitrokyosho
      @nitrokyosho  ปีที่แล้ว

      Try a steam machine you can
      Buy them at home depot cheap and they work ,I have a video demonstration on TH-cam. Wanger 725 $50.00

  • @Stolesher
    @Stolesher ปีที่แล้ว +1

    After I removed the wallpaper (took me literally less than a minute, pieces came out by themselves) the whole wall was covered with green goo (glue?) How do I remove it? I tried water, soap, vinegar, hydrogen peroxide, none of it works.

    • @nitrokyosho
      @nitrokyosho  ปีที่แล้ว

      I have never seen green glue should be clear or white not sure but sounds like who ever put the paper on used the wrong product. It should wipe off with a dense sponge and hot water.

    • @Stolesher
      @Stolesher ปีที่แล้ว

      @@nitrokyosho looks like a kid painted the wall with a watery green color and it's completely removed from the actual wallpaper which itself comes off easily.

  • @ellal5750
    @ellal5750 2 ปีที่แล้ว

    Can I use fiber cloths?

    • @nitrokyosho
      @nitrokyosho  2 ปีที่แล้ว

      I use a sponge but give it a try

  • @pouyanebrahimilialekol2197
    @pouyanebrahimilialekol2197 4 ปีที่แล้ว +1

    Awesome! It is working!

  • @andrewhills6535
    @andrewhills6535 2 ปีที่แล้ว +1

    Thanks

  • @katelynkopa8549
    @katelynkopa8549 4 ปีที่แล้ว

    These are great but what's the next step?! Thanks!

    • @nitrokyosho
      @nitrokyosho  4 ปีที่แล้ว +3

      Fix any wall defects with some spackle then prime and paint

  • @TM-ge4xg
    @TM-ge4xg 2 ปีที่แล้ว

    Where's the next video after this ?

  • @rexorbernarte4487
    @rexorbernarte4487 3 ปีที่แล้ว +1

    So what the next step guys? help me pls

    • @nitrokyosho
      @nitrokyosho  3 ปีที่แล้ว +2

      Now patch any wall imperfections then prime with kilz water base primer and paint

  • @acheng9938
    @acheng9938 3 ปีที่แล้ว

    My glue is mega thick. I have repeated four times and still have the glue on the cement wall .

    • @nitrokyosho
      @nitrokyosho  3 ปีที่แล้ว +2

      I would try using a 3 inch putty knife after the glue is activated and use it to gently scrap the glue off the wall

  • @Sophia-gi5io
    @Sophia-gi5io ปีที่แล้ว

    Where's part two?

    • @nitrokyosho
      @nitrokyosho  ปีที่แล้ว +1

      The next step is to spackle any damage on the wall prime and paint it and you're done