Thanks Alan. I'm glad that someone was able to figure this out and share it. Demonstrations of any other DRO functions would be appreciated. I just installed the exact same model of 3 axis DRO. I was disappointed to find that this model has less functions than some others and in fact has less functions than previous versions of this same model. Several buttons are "missing".
Ya one of the better DRO video's I've ever seen. No kidding the DRO can help you make some super acurate tools make sure your indicator is on center hight for tapers. Realy great for compound angle's set the vise toe clamped at the one angle and a custom? angle block in the jaw's. no swival base no angle plate no roatery table if your lucky you won't ever need any of that. achiner'ys hand book has the tables for 100 mm x and 5" X use it all the time ha ha Thanks great video very entertaining stuff
Thanks, Alan. Very useful. I have a combo lathe and mill, so I have the DRO set up as x=length and y=diameter all the time. It's just a matter of getting used to it. 😊😊
Hmmmm...I need to check that the face of my top slide is parallel to the travel and fix it if it is not. This could be very useful for setting short tapers. I never had the "inclination" to look into this feature before. Thanks!
Hi Alan very well explained and clear . Never had a DRO before on my lathe I'm finding it very handy but some of the settings are very confusing to me so your video was very helpful . Thanks for taking the time to post your video kind regards Shaun PS always nice to watch thanks 😀
By some reason Your last videos comes up with text in my mobile phone. That's new to me, text.... Watching the same video using the Pc, there's no text. This only happends to Your videos. When the text appears that strip is effectivly hiding the work You are showing. Strange. Any tip?
The subtitles are on all of my videos but you need to turn them on to see them. your phone must have it turned on you need to turn off subtitles on you phone
When on you tube on your phone touch the screen you should see three dots on the top right hand touch the dots and a screen should open showing you caption on change it to captions off
@@enotsengineering Thanks a lot Alan! As You sometimes say, "Spot on!". Just did as You told and there it is. It puzzled me because it has only been on Your videos and it started without reason, without explanation. Now it's cured! However, for viewers using the text, remember that the lower 1/4, 1/3 of the frame is hidden by the text.
Thanks Alan. I'm glad that someone was able to figure this out and share it. Demonstrations of any other DRO functions would be appreciated. I just installed the exact same model of 3 axis DRO. I was disappointed to find that this model has less functions than some others and in fact has less functions than previous versions of this same model. Several buttons are "missing".
Ya one of the better DRO video's I've ever seen. No kidding the DRO can help you make some super acurate tools make sure your indicator is on center hight for tapers. Realy great for compound angle's set the vise toe clamped at the one angle and a custom? angle block in the jaw's. no swival base no angle plate no roatery table if your lucky you won't ever need any of that. achiner'ys hand book has the tables for 100 mm x and 5" X use it all the time ha ha Thanks great video very entertaining stuff
Thank You, I have looked at it a number of times, I could never figure it out. Great information, once again Thank you..
Good morning Alan! Great episode.
Thanks, Alan. Very useful. I have a combo lathe and mill, so I have the DRO set up as x=length and y=diameter all the time. It's just a matter of getting used to it. 😊😊
Thats a helpful procedure Alan.Thanks.
Clear and helpful
Hmmmm...I need to check that the face of my top slide is parallel to the travel and fix it if it is not. This could be very useful for setting short tapers. I never had the "inclination" to look into this feature before. Thanks!
Super useful thanks for sharing.
Glad it was helpful!
Hi Alan very well explained and clear . Never had a DRO before on my lathe I'm finding it very handy but some of the settings are very confusing to me so your video was very helpful . Thanks for taking the time to post your video kind regards Shaun PS always nice to watch thanks 😀
Glad it helped
Helpful information. Thanks!
By some reason Your last videos comes up with text in my mobile phone. That's new to me, text.... Watching the same video using the Pc, there's no text. This only happends to Your videos.
When the text appears that strip is effectivly hiding the work You are showing. Strange. Any tip?
The subtitles are on all of my videos but you need to turn them on to see them. your phone must have it turned on you need to turn off subtitles on you phone
@@enotsengineering All You are saying is showing up in text on 2 lines a bit down on the screen. I've never seen "subtitles" in the phone near TH-cam.
When on you tube on your phone touch the screen you should see three dots on the top right hand
touch the dots and a screen should open showing you caption on change it to captions off
@@enotsengineering Thanks a lot Alan! As You sometimes say, "Spot on!". Just did as You told and there it is.
It puzzled me because it has only been on Your videos and it started without reason, without explanation. Now it's cured!
However, for viewers using the text, remember that the lower 1/4, 1/3 of the frame is hidden by the text.