So I'm trying to make a drawing of the flat patterned helixed part. But I'm having trouble dimensioning it since it's not really a circle. What's the best way to dimension it and check out that it's correct? Cut it out and lay it on a 1:1 print?
Thank you for your lessons. I keep getting an error when I create a flat pattee that the part contains features which cannot be unbent and I guess it's the pipe. What should I do
Thanks for your lessons. I am ordered two weeks of free program testing section. This lesson will help me because I doing almost similar things. But I am 99,9% sure that the flat steel part did not make one round of helix. If I cut a fully round circle and welded them together to drag them to the helix. The seam will be turning almost that much like your example shows, (After about 30 flat section you have about 29round of the helix) even the starting point was fully round. It is obvious. because the material perimeter does not enough, one full round of helix perimeter (girth) is longer than the same on the flat round. Therefore each flat round part after drag to helix makes less than one round helix. That's is not your false, the program makes it that way. Easy to follow your speech even I am speaking Finnish and intermediate English. Bye, the way -21 degrees outside right now.
Can we increase the height or length of the helix/spiral instead of using pattern it.. Or is there no option for increasing length of the helix?? And while we using catia , there is a option for increasing / decreasing the length of the helix/spiral... Please clear my doubt in detailed information.
Bro You still have not replied I have asked few times. Why do I need to join your lectures and pay whereas I can learn from your youtube channels everything for free? However your videos are excellent and I appreciate you making such nice videos and making me learnt so easily long awaited program to learn. Cheers Bro and dont forget to reply me please. Thanks
Why did you make this so hard you just need to make a second helical sketch with the OD of the flight then just convert the helixes to 3D sketches and skip the entire middle part
I do not understand how the flattened form is less than a full rotation and each spiral section rotates 360 degrees and also travels in the z dimension. I feel like the flattened form should be more than a full rotation.. I wish I understood why now
You may have found the reason, just incase. The reason for making flat pattern is to facilitate mark then cut or g code laser cut flat sheet metal. Spiral length beyond certain value of 1 revolution one round will cause an overlap in flat pattern which is not feasible and of no use. Another point is the flat pattern also looks round but the inner edge perimeter will be more than the cylinder OD perimeter where it was 3d sketched. When it is bent over the original dia pipe the flat sheet the radial edges end align along a single plane allowing for copying sections to increase length.
Scewr conver 300mm, length 15'f ,metrial ice cutting meshion hour in 8000 kg daimention no idea to help... And I am gujrati. So plz on my commet help us..
It's almost 2023, and your lecture videos are still used in production. Thank you, sir.
One of the best Solidworks teachers out there! perfect thankyou.
Absolutely Great !! Thank you . Little adjustments to the real parts and your are pack to go. Perfect. Thanks to share your knowledge like this.
Thank you sir, because of your video my project can be completed quickly
You have been my guru for quiet sometime now.
Very thankful,sharing this courses.
Brilliant tutorial! Did this on Solidworks 2011 no problem!
I managed to do it step by step as I explain in the video even though my native language is Spanish. Thank you sir.
A very useful video, Thank you very much for your valuable teaching for self learners, keep it up, May the God Bless You
Thank you sir it's very helpful
thanks for your lesson sir
THANKS ALOT SIR. IT HELPED ME A LOT
Super.
How should I create Helical Screw Conveyor but with variable pitch ?
I need also parts for one pitch.
Thank you.
BR
Peter
So I'm trying to make a drawing of the flat patterned helixed part. But I'm having trouble dimensioning it since it's not really a circle. What's the best way to dimension it and check out that it's correct? Cut it out and lay it on a 1:1 print?
Very nice I like it Thank you sir.
Thanks for the help!
thank you soo much its very useful
Thanks for making this vedio.. Beacause useful for me...
Thank you for your lessons. I keep getting an error when I create a flat pattee that the part contains features which cannot be unbent and I guess it's the pipe. What should I do
You are a master
Always appreciated your work👍👍 Your my online teacher .. Thanks sir🙂
Great Video!! I followed along and had very little to no trouble! I'm subscribing! Thank you!!
This video is very useful. Thank you Sir. Please teach us how to make a bucket elevator
Very useful thank you
Brother please try post video of the screw flight DIE and mold design video... It's very useful...
Great video thank you for sharing!!!!👍👍👍
thnx
Es muy buena la explicación...
Thanks a lot Sir
Is there any ready recknor to find out ID and O D of the conveyor section
So this is a softcopy. How to make hardcopy? Can you tell me? Cnc Or 3d print?
The video is really awesome
Sir can u please explain about the working of spiral conveyor
Gracias, excelente, felicidades, Ud. Me ayuda mucho con sus videos, sigua adelante, éxitos.
Very nicely explained sir. Thank you !!!
thanks for ur totorials, u always are help me with my dude, thanks continue there
help me with my doubt xD
great video sir !! thanks a lot for sharing
Thanks
Very good
can you make a tutorial on how to make a clutch, such as a spiral jaw clutch, centrifugal clutch, cone clutch and other clutches please
"brain explosion" thank you very much for sharing this method, solidworks continues to amaze me!
Lofted bends me profile select nhi ho pa rha hai.. Please btaye?
what is the angle of cutout on the disk i am making this by hand
Thanks for your lessons. I am ordered two weeks of free program testing section. This lesson will help me because I doing almost similar things. But I am 99,9% sure that the flat steel part did not make one round of helix. If I cut a fully round circle and welded them together to drag them to the helix. The seam will be turning almost that much like your example shows, (After about 30 flat section you have about 29round of the helix) even the starting point was fully round. It is obvious. because the material perimeter does not enough, one full round of helix perimeter (girth) is longer than the same on the flat round. Therefore each flat round part after drag to helix makes less than one round helix. That's is not your false, the program makes it that way. Easy to follow your speech even I am speaking Finnish and intermediate English. Bye, the way -21 degrees outside right now.
What process would one use to form the helical from the flat part.
I am not able to lofted bend what should I do
Thanks a lot , please design a conical screw
This is great thanks.
Thanks!
Congratulates on Reaching 70K+ Subs.
Awesome
Can we increase the height or length of the helix/spiral instead of using pattern it.. Or is there no option for increasing length of the helix?? And while we using catia , there is a option for increasing / decreasing the length of the helix/spiral... Please clear my doubt in detailed information.
Thank you sir, we got what we needed🙏🏻
Спасибо за видеурок. Отлично!
How to calculate inside whole and outside size of round plate as the size of plate is changed while it is cut and expanded on the rod?
Thank You... I Enjoy the Rhythm of the Swamp Cooler Air Conditioning in the Background.... You in Kolkata or Mumbai?
Thank you very much
How to process in machine mean to say....... How this made on vmc or afyer drawing process.
Looft bend can not accept the converted arc of the the spiral in 2015 version solid works
Alguien me puede decir que software es ese para adquirirlo
Hello sir, can we do this in 2008 or 2012 version also?
what is the ID and OD of Flat form
Why did you have to use the longest method to make this?
Any other options for sheet metal looft bend
We insert 2d drawing to solidwork for 3d
Thanks sir.
But I cant understand why u save in .dfx formate ?
Niranjan Akhil .dfx file format used for CNC machine programming, once design finish make program and cut in machine,
To send to Laser Cutter or CNC Plasma., or even a printer for a pencil stencil.
You can save it as a parasolid and upload this file into master cam to program the machining as well as a dxf.
how to make dimension in the flatten Helical screw .( outer and inner Dia)
Bro You still have not replied I have asked few times. Why do I need to join your lectures and pay whereas I can learn from your youtube channels everything for free? However your videos are excellent and I appreciate you making such nice videos and making me learnt so easily long awaited program to learn. Cheers Bro and dont forget to reply me please. Thanks
how do i do this on solidworks 2019?
SUPER💛❤
Thank you sir
Kay ap mojay Ak warm ka size Bata day gay
Sir,
Thank you
Why did you make this so hard you just need to make a second helical sketch with the OD of the flight then just convert the helixes to 3D sketches and skip the entire middle part
I do not understand how the flattened form is less than a full rotation and each spiral section rotates 360 degrees and also travels in the z dimension. I feel like the flattened form should be more than a full rotation.. I wish I understood why now
You may have found the reason, just incase. The reason for making flat pattern is to facilitate mark then cut or g code laser cut flat sheet metal. Spiral length beyond certain value of 1 revolution one round will cause an overlap in flat pattern which is not feasible and of no use. Another point is the flat pattern also looks round but the inner edge perimeter will be more than the cylinder OD perimeter where it was 3d sketched. When it is bent over the original dia pipe the flat sheet the radial edges end align along a single plane allowing for copying sections to increase length.
@@muthumanikya1847 nice! that totally makes sense
Nice
Sir how to download the solid works software
Are u have link to download solidworks for free??
Will you make it for me
Elegante
Give me Flattening machine diagram
Scewr conver 300mm, length 15'f ,metrial ice cutting meshion hour in 8000 kg daimention no idea to help... And I am gujrati. So plz on my commet help us..
Sir hindi me bhi banao na
Can't select profile 4:50
Same problem here! Did you find a solution?
Very same problem, quite irritating, can't seem to find a solution
You should choose 2 different 3d sketches for each profile curve, had the same problem, now working perfectly
im fucked if i can get it,,,,,frustrated
G
Thank you so much.
thank you sir.
Nice
Thank you very much
Thank you so much
Thank you sir
Thank you sir