TECH TIP - Solution to foam rubber deteriorating. I have been using this bike rack for a few weeks and it did not take long for the foam rubber protection to start to disintegrate. Especially when clamping down near the folding welds on the XP. The uneven welds/hinge area causes excessive wear on the foam rubber. I load two XP's and flip the bikes so the fronts point in opposite directions. This results in the KAC rack clamping on one of the XP's right around the weld/folding hinge area. The solution is I went to Home Depot and purchased a dishwasher drain hose. This is a heavy duty rubber hose with a 5/8" inside diameter. I removed the old foam and replace with the same length of dishwater hose. A little WD-40 and they went right on. Not only is the hose more durable, it grips the bike frame better, and not not mar the paint like the foam when highly compressed.
We have owned an Overdrive Sport-2 for almost a year. Over 10k miles since end of last May...cross country plus up into Canada with our 2 RAD eBikes....HIGHLY recommend.
To work on the bike in an upright position, as opposed to handlebars and seat, I have repurposed a heavy patio umbrella stand, using a closet pole in place of the umbrella. I lift the bike over the top of the pole and lower it onto the pole and into the pipe that holds the seat. It is high enough to raise the bike so I can hand pedal the bike for adjustments. Works like a charm.. BTW, if you are having trouble raising the XP onto this rack, it's even more trouble loading it into the bed of a pickup truck. I have removed the jump seat from my truck (not needed) and load the folded bike into the back and bungee around the seat pipe to the passenger headrest.. This method will accommodate two XP's, one behind each seat..
I have two step thru e bikes and wondering if the clamps go down far enough to secure the bikes or would you use an adapter bar to secure the bikes? Thanks for a very clear and honest video.
Thanks for the comment and concern about my bike rack.I didn't make theYou Tube video but my last E-mail with them i told them I was going to make one and show the world the parts that failed and wore, fact they don't stand behind their warranty, and that they don't stock replacement parts! Well new KAC 4 bike rack arrived yesterday. I spent $175 for a welding shop to replace weak part with new and heavier metal and weld gussets on the vertical posts the stronger those areas also. Looks like this rack might be going on the market
Instead of installing wood on the mount to fit the little bike, you might want to try heavy duty zip ties across the mounts to shorten the length. Thanks for the good video, covered a lot of what I was curious about.
The comments are very good. I had my experience with the Aston Rider kit, it came out less than 6lb and 268USD with lifepo battery and it has been running without problems since I had it more than a year ago
I have a rear hitch motorcycle rack from Harbor Freight, Haul-Master, Item #:62837. It is rated at 400 lbs., made entirely from aluminum and has a attached loading ramp as well. No need to lift the bike/motorcycle into the rack. However, it is only for a single motorcycle. A reviewer indicated that he uses this rack for his heavy e-bike. I have carried a 250cc motorcycle on it; next time I will try carrying the Lectric XP.
Thank you for you tip, the motorcycle carrier will definitely work and I have recommended it to other people that only need to transport 1 bike however I’m usually carrying 3 bikes so it won’t work for me!😢.
I really wanted to like this rack but it doesn't work on my FJ Cruiser. The part that bends up will block my door from opening because my spare tire is in the way. So for anyone with a rear door that swings open, you'll want to check clearance. That bend that comes up is pretty big and will get in the way. Imho this is best for hatch type doors.
One thing that is important is the quality and grade of the metal throughout. low-grade metal will fatigue. Especially the hook that holds down on the frame, As a precaution, add winch straps for safety. Also as previously mentioned replace the foam hook hold-down pads with rubber. Foam is unacceptable.
I know there has been a few people that loaded the bike rack up with 4 E-bikes on the Lectric Facebook group however I would be very cautious about that and not sure if I would trust it to be honest. It may hold but sometimes I worry about the little things like that lol.
Jeremiah McIntosh, great video. Very detailed and informative. I have been using this rack for a few months now. I have 2 fat tire e bikes that weigh 65lbs a piece. I take out the battery when transporting. Help take off 15 lbs per bike. Heavy duty rack. Do you have anybidea how to stop the side to side wobble? The anti wobble works great for the hitch insert but not the over all wobble coming from the adjustable section.
I just got one for my MTB and families bikes. It is super heavy duty and heavy. I like everything you get with the rack. Was missing end cap and they sent me one right away. Love everything except I wish the hold down bars would rotate making it easier to load and unload the bike without having to tilt the bike.
If you slide the holding bars off then you can bend fold down the middle one and easily put the bike on then fold it back up, that is what I do with my bike because it is around 60 pounds!
Hey Jeremiah, Very informative vid as always. I did found something interesting. I purchased the KAC Overdrive Sports K2. The manual states 60lbs per bike. My Lectric will be mounted on the inside & a lighter bike will be on the outside. I think I'll be fine, this rack is very well built! Cheers!
Thanks for the review. My Lectric 3.0 weighs 64 lbs plus the racks. I notice you mention the manual stats 65-pound capacity. I went online and looked at the manual, which says 60-pound capacity? I was wondering where you sew the higher weight rating. Just want to be safe hauling our 2 Lectric bikes.
It was in my manual but they may have changed it. If you gave the battery’s out you will be under the 60# limit. You can also take the seat out to make it even lighter yet.
This looks like the best of many racks I’ve looked at so far for our Lectric step-thru e-bikes. Thanks for the video review so we can see it in action. How much of little do the bikes wobble (side to side) when driving?
I'm glad Overdrive offered a fat tire version instead of offering the standard version where you would have to drop another $60 on fat tire holders and then you are left with holders you paid for but don't need.
The only difference I’m aware of is the older style like I have has knobs that you turn to tighten on the center hold down clamp and only one locks. The new model has more of a ratcheting style hold down bracket and each one locks. To be honest I’m not sure which one is better but I would lock the bikes with a heavy chain as well if left unattended.
Hi there, I have a fat tire trike as well as a fat tire bike. Have been trying to find a platform carrier large enough to accomodate both but no luck. I see your multi bike rack here and am wondering if it an be altered for putting a 3 wheel trike on it as well as my bike. Can you offer any assit please?
Hi Jeremiah, great video--very informative! I've asked KAC for a couple measurements, but they can't seem to provide this for me--could you tell me the distance from the center of the second wheel hoop to the center of the fourth wheel hoop, and the distance from the inside edge (nearest vehicle) of the second hoop to the inside edge (to rear away from vehicle) of the fourth hoop? Also, I need 2 measurements on the L-shaped piece of frame that goes into the hitch: what is vertical distance from the top of the horizontal piece of L to the top of the vertical part of the L, and what is the distance from the hitch to the inside of the vertical part? Thanks so much.
How much it hangs backwards, how much more entimeters i lengthens your car with bikes on it and the 4th bike handlebar sticing litle bi out when folded , so overal, in both 1 2 3 and 4 bike modes? could you measure it please?
Jeremiah, do you think this rack will hold and secure Two of the new Lectric XP Step thru models with its lower cross member? Enjoy your videos...very informative!
I’m sure it would hold 2 weight wise but not sure how good it would hold them down being a step through. I plan on getting one and I will make a video on it if I do.
Hello again Jeremiah Great videos you go into a lot of detail on the overdrive 4 bike heavy duty bike rack. And No deafening loud music just plain info and good info I sent you a comment aprox 22 hours ago on the same rack was wondering if you read it please as asked for a bit more info on the bike rack. Thank you mate. PAUL H ( UK)
Do you know if the company Overdrive sport bike rack for 4 Electric bikes will ship there bike rack too Canada . I just found out they wont ship overseas to EUROPE so annoying.
Great review, well done. But I don't think the locking mechanism with the square pin that slides into an open slot is good enough. You noticed it too, and made a comment at 3:05 of your video. I'd drill a hole and put a bolt through. I realize the manufacturer wanted a quick way to be able to move the rack, but I see problems on a bumpy road and over time when that mechanism gets worn.
I agree with you and have always been a little skeptical of that however with that being said I have not done anything with mine yet and have been using it with no problems. With a longer trip I would probably consider doing as you suggested with drilling a hole and using a pin or a bolt in it.
You should not have a problem with 2 bikes on the 2” version it seems very strong however the spring loaded latching pin that keeps the rack from tilting makes me think maybe I should drill and put a pin under just in case it fails and Pops out. With that being said tho I have not had any problems with it but I’m just a cautious guy lol.
Great review, excellent info. I have a Curt basket cargo carrier. Would it fit in the receiver that is made to connect the extra 2 bike carrier? The Curt basket has a 2” male connection.
Great question. Probably not because the receiver part of the main rack inside dimension is 1 11/16 x 1 11/16 ...outside is 2” x 2” which would be the same as your rack. You may be able to make some kind of adapter out of square tubing to fit in your rack that will fit in this rack kind of like the extender for the four bikes.
Unfortunately, my fat-tire e-bike I ordered is 70 lbs., so I'd be over on this weight wise. If/when my wife wants an e-bike, if she gets one like mine, we'd really be over on weight. Looking for extra-heavy duty racks I guess. Thanks for the video Jeremiah...much appreciated!
Hello Jeremiah, I watcht many of your videos and respect your opinion. I'm asking for your advice. My wife n I are looking for a bike rack for our Lectric XP step through. I have a bad back and we drive a 2007 Toyota Tacoma, can you recommend a durable rack that's not too high off the ground that I can attach to my 2" hitch m?
The only issue I see is the clamps that come down to hold the bikes. you may have to shift one bike to one side or the other for the clamps to come down to hold the bikes if that makes sense or figure out a way to put a top tube bar on for the other clamp to hold the bike. kind of hard to explain but I haven’t really tried it yet with two steps throughs that’s just from my speculation.
I like your review in how thorough it is. I'm concerned with your comment that you can remove the whole rack by removing two bolts. It that only for the last two bikes or for all four? Why is there a key connected to the hitch if you can just remove the whole rack relatively easily. How are the bikes individually secured to the rack? Thanks for your time.
Where the rack folds up on the vehicle there is only one bolt that holds it on there and if you remove that bolt You can basically remove the whole rack. This can be prevented by replacing the bolt with a locking hitch pin or welding the Nutt onto the bolt so that it could not be removed. I’m pretty sure this is probably the same with most bike racks and I recommend using a heavy duty chain lock to lock the bikes to the vehicle if you leave them anywhere unattended.
I think any hitch mounted bike mount will work for an ebike as long as the tires fit properly. The weight should not be a factor as long as the electric bike is mounted closest to the hitch. You can buy a cheap walmart hitch mount for bicycles and a human that weighs 150 plus pounds can stand on the bike rack on the main support beam closest to the hitch. You could not stand on the sides where the tires go of course. I think the weight recommendations are just a safety factor and to keep people from trying to put a heavy dirt bike on a bicycle mount. Old timers would make anything work that they had laying around. The modern generation always wants the best of everything and tries to evaluate every aspect of products and safety. I am guilty of it myself. Not sure if that makes us better or worse than the old timers in the long run. I guess time will tell.
That’s the problem with most fat tires they don’t usually fit unless you buy additional fat tire racks which this one includes. I did not shown in the video but I stood on the back of the hitch when it was all together plus had my ebike mounted up close to the car and it supported me no problem at 160 pounds plus the bike. However going down the road hitting bumps obviously will put more stress on it but I don’t think it will be a problem at all.
@@JeremiahMcintoshYea, those hitch mounts seem to move around a little in the hitch of the vehicle. I have a regular two bike hitch carrier and the electric bike fits in it fine, the only problem is that the fat tires slide down into where the wheels go. It just makes it a little snug when you go to get it out. Whats the inside width measurement where the tires sit, on that one? I have the two bike Swagman and the inside width is 3 and a half inches. It says it is rated for 35 pounds a bike. I have had the lectric xp and another bike on there and stood on it and it is solid. That is over 300 lbs on the swagman and it does not bend etc. Maybe the companies are being cautious when they tell you that it is only designed to hold a certain weight. I am pretty sure the swagman will hold 500 pounds plus if it is evenly distributed before it would bend.
How right you are..!! People spend more time deciding on the latest over-priced cell phone rather than educating their children..!! What a sad state of affairs this country is in....
I would go slow over speed bumps but I have not had any problems with it yet. I would like to add some sort of additional safety pin just for extra security bit I haven’t needed it yet.
I think it would work but that’s a lot of weight I would take out the batteries. I personally would be nervous with 3!but I’ve seen photos of others using it with 3-4 Lectric bikes without problems on the Facebook forum.
I would suggest going on the Facebook forum and I think Brian Cohen or some thing is the one that I seen Had a picture with four bikes on the rack maybe ask on there you might be able to get some more opinions.
It works good with both of our bikes however we have one of each. The only thing that would be difficult with two step Throughs is the arm that comes down to secure the bikes are two different lengths and the taller one may not come down far enough to hold the tube on one of the step throughs. You might have to figure out how to put some sort of top tube Bar on one of the bikes if that makes sense.
@@JeremiahMcintosh thanks for the very fast response. We purchased two step thrus and are now looking for a carrier. Like you, I dont want to spend as much for a carrier as a bike but still need something strong enough to carry them both. Your vids are the reason we went with Lectric bikes like your wife's. Thanks, Bruce
No problem that’s awesome I’m glad I could help. Like I said it would probably work but you may have to add a top tube bracket like the one I showed and one of my bike rack videos to go from the base of the handlebars to the seat post and then the clamp can hold it down there. Honestly you would probably have the same problem with any bike rack. Some bike racks have the holders that hold the wheels down instead of the bike itself but you might run into an issue with the fenders with that style.
I specifically didn't buy a fat-bike because range was my primary focus. I wanted to be able to ride 100 miles with a fully loaded (more like over-loaded) tour bike pulling a single wheel suspension trailer. More and more often when I ride on biking infrastructure I see fat-bikes riding in pairs and small groups. I'd love to be able to ride over and through everything they can with 4" tires. The biggest drawback I have seenwith fat-bikes is having to transport them places to ride. I was riding the Foothills trail near Orting, WA and watched a little lady (wife I presume) about 130 lbs. 5'7" unload a fat-bike (her husbands I think) to get to the other fat-bike and then unload it. She lifted the back tire off the stand and drops it to the ground, She squeezes the back brake and pulls back on the bars lifting the front tire up and over the carrier and down to the ground... not even straining. After both bikes are on the ground she opened the back door of the car to grab her water bottle and rode off while a guy sat in the car on the phone the whole time. Ya know... I'm not so sure she was coming back. If those bikes had been in the back of a pickup rather than a low trailer rack I might have had to help her Bike pics: prior to Oct 2019 photos.google.com/share/AF1QipN67sUw0ykU-Mg5gLsOw9vF8kBMEM5cGCgCNmLT_j72h9iu5fKYFFVbLJ2Z415Umw?key=LUZqdEl1d3RjNV9id0ZvTEFickhITnBwWFZrU3hR
Thank you so much for that detailed description. As a single older woman, I've been debating whether to invest in an e-bike due to doubts about how in the world I would wrestle it on & off a rack. Now I feel confident that I could manage it! Thanks!
I bought the two fat tire bike version for my 1.5 inch receiver last fall. The rack flops around loosely in the receiver because it arrived without a set screw to tighten the connection. I have scoured the internet for any mention of Overdrive bike racks, but the company does not seem to exist. Amazon also says that the company does not exist either, and offers no warranty support whatsoever. So now I am stuck with a defective product from a non existent company with zero customer support. Does anyone know what kind of screw fastener I need to look for is that will allow me to tighten the bar to receiver connection?
It should of come with a Locking anti-rattle bolt as seen in my video, in fact mine came with one extra one as well. The company you are looking for is overdrive brands and you can contact them through Amazon where it says shipped from and sold by maybe they can send you another one but ultimately if it was missing when you received it you should’ve maybe just returned it and bought another one if they would not send you a new pin. I’ll see if using a regular pin you may be able to use an anti-rattle mechanism like this amzn.to/2x3KptX Just keep in mind This is a affiliate link and I will get a small commission if it is purchased through this link which is no extra cost to you. Hope this helps.
HELLO JEREMIAH, VERY GOOD VIDEO on the fat tyre bike rack heavy duty electric bikes , Overdrive sport for 4 bikes. I may purchase this one for a two wheel e bike and a adult European UK tricycle. ( ALPINE EXPLORER ELECRTIC TRICYCLE , in ENGLAND UK and a fat tyre 2 wheeled e-bike like the SONDORS XS FOLD . ) THIS WILL CARRY THE WEIGHT fine if I remove the battery packs. can you tell me if I am able to fix a LIGHT BOARD ON THIS BIKE RACK for tail lights and directional indicators can be seen clearly. this would be fitted onto my RV HERE. AM WAITING FOR some info from the manufacture off the ALPINE EXPLORER TRICYCLE ( its on TH-cam & there website video ) for the distance measurement (gap) between the rear two wheels centre off the tyre to centre off tyre, CAN YOU TELL ME MATE is there any way off adjusting the gap closing it up or widening it off the wheel tray ( wheel holder ) on one bike rack too the other wheel holder on the bike rail. so you can move the bikes further apart or a little closer if needed. PARTICULAR for the centre wheel holder that you showed was only 10.5 inches apart instead off the 12.5 inches gap off the first bike wheel holder. much appreciated thank you kindly Jeremiah. Paul H
I doubt it....these ebikes are heavy but this rack seems to hold them well with no problems. Currently the four bike one is on sale for the lowest I’ve ever seen it.
@@JeremiahMcintosh Amazon has got one that is supposed to hold 60 lbs. That is much too close to the weight of the Lectric, less you remove the battery
As I’ve said in the video amazon has it listed as 60lb per bike but the manual states 66lb per bike for the 2” hitch version. But yes you are right about taking the batteries out.
@@JeremiahMcintosh about 64 pounds without battery. I was more worried if the rack is long enough. I wanted to get the Overdrive bike rack for the 1.25 hitch.
Absolutely it will definitely hold 2 Lectric bikes! It is rated for 66 pounds per bike in the manual so no problem for weight or size. I weigh 160 pounds and stood on the rack and it held me just fine.
Covering up the license plate is just another reason for the police to stop you... also covering up the bikes with a tarp can block your tail lights... this is a problem with all the hitch racks
LOL I wouldn’t cover up the license plate while driving down the road but good point on the grill cover ...I did not think about it covering the tail lights. 🤔
@@JeremiahMcintosh Take another look at your set-up.....you are covering your plate location..Lol... you can't have anything in view of your plates... not even a hitch ball if it block the plate... its a reason to be stop. I have the same problem with my 1up-usa rack... I have to relocate my plate to the back of the rack. If I fold down the seat and handlebar I'll be okay with the lights if I have the cover on.....I don't want to be rear-ended. Here in the State of California you can't have any type covering your plates. That included the smoke or clear plastic protector... even if they sale it in the local part store. They get really strict because of all the toll bridges and lanes....also the red light camera. To make this all legal you also have to have a license plate light....... It just doesn't stop to have everything legal
You are absolutely correct but if you need the extra storage space when you’re going on a trip is nice to have the option to transport it externally as I said in the video. I doubt you’ll find a nicer bike for A comparable price of the lectric though. Or if you’re transporting other bikes that are not foldable like I will this is a great rack because you can use it for both.
@J Hunt Actually you could probably use It with a cargo carrier ...fold your bike up put it in a tote and strap it to that however I needed something that was going to carry my families bikes as well.
@pedro fernandez Haha well thank you I appreciate that! I am very frugal when purchasing things and tend to research my purchases prior to buying that’s why I like to share my experiences with items I purchased to help other people out especially with questions I had that I could not find the answers to.
TECH TIP - Solution to foam rubber deteriorating. I have been using this bike rack for a few weeks and it did not take long for the foam rubber protection to start to disintegrate. Especially when clamping down near the folding welds on the XP. The uneven welds/hinge area causes excessive wear on the foam rubber. I load two XP's and flip the bikes so the fronts point in opposite directions. This results in the KAC rack clamping on one of the XP's right around the weld/folding hinge area. The solution is I went to Home Depot and purchased a dishwasher drain hose. This is a heavy duty rubber hose with a 5/8" inside diameter. I removed the old foam and replace with the same length of dishwater hose. A little WD-40 and they went right on. Not only is the hose more durable, it grips the bike frame better, and not not mar the paint like the foam when highly compressed.
Are you concerned about the weight of the bikes. Mine is a xp 2.0 and says they weigh 64lbs. And the carrier only holds 120lbs?
I always take the batteries out and that that will put the bikes under the 60lb limit per bike.
Excellent presentations, one of the few I've subscribed to. Thanks for your videos WITHOUT IRRITATING, overbearing music!!!
Thank you @tennisbum I really appreciate that!
We have owned an Overdrive Sport-2 for almost a year. Over 10k miles since end of last May...cross country plus up into Canada with our 2 RAD eBikes....HIGHLY recommend.
Wow that’s awesome! Thank you for the update especially with that many miles!
Which model of radpowerbikes did you get? The radrunner doesn't have a crossbar, wondering if this rack will work?
@@christiffkennedy We have 2...2018 mini and 2018 City Step through. I use the overdrive crossbar adapter on the step through...14k now.
To work on the bike in an upright position, as opposed to handlebars and seat, I have repurposed a heavy patio umbrella stand, using a closet pole in place of the umbrella.
I lift the bike over the top of the pole and lower it onto the pole and into the pipe that holds the seat. It is high enough to raise the bike so I can hand pedal the bike for adjustments. Works like a charm..
BTW, if you are having trouble raising the XP onto this rack, it's even more trouble loading it into the bed of a pickup truck. I have removed the jump seat from my truck (not needed) and load the folded bike into the back and bungee around the seat pipe to the passenger headrest.. This method will accommodate two XP's, one behind each seat..
I have two step thru e bikes and wondering if the clamps go down far enough to secure the bikes or would you use an adapter bar to secure the bikes? Thanks for a very clear and honest video.
Thanks for the comment and concern about my bike rack.I didn't make theYou Tube video but my last E-mail with them i told them I was going to make one and show the world the parts that failed and wore, fact they don't stand behind their warranty, and that they don't stock replacement parts! Well new KAC 4 bike rack arrived yesterday. I spent $175 for a welding shop to replace weak part with new and heavier metal and weld gussets on the vertical posts the stronger those areas also. Looks like this rack might be going on the market
Glad they finally took care of you. If you have Instagram can you send me some photos of your upgrade?
@@JeremiahMcintosh Sorry I don't have instagram, can send via tx or E-mail pics
Thanks so much for such a thorough review. We have 2 65lb ebikes and 1 52lb e bike and need a rack for all 3.
Great review. I ordered the newer model that holds two bikes. As always Jeremiah, great work informing the Lectric XP community.
Thank you you’re welcome!
Thank you for taking the time to make this video! It's great!
Thank You! Glad you found it helpful!
Thanks for taking time and creating this very detailed and meticulous review!
Thank you! You’re welcome!
This bike and company is phenomenal.
Instead of installing wood on the mount to fit the little bike, you might want to try heavy duty zip ties across the mounts to shorten the length.
Thanks for the good video, covered a lot of what I was curious about.
Thanks Brian that’s a good idea about the zip ties! Glad it answered some of you questions.
The comments are very good. I had my experience with the Aston Rider kit, it came out less than 6lb and 268USD with lifepo battery and it has been running without problems since I had it more than a year ago
I have a rear hitch motorcycle rack from Harbor Freight, Haul-Master, Item #:62837. It is rated at 400 lbs., made entirely from aluminum and has a attached loading ramp as well. No need to lift the bike/motorcycle into the rack. However, it is only for a single motorcycle. A reviewer indicated that he uses this rack for his heavy e-bike. I have carried a 250cc motorcycle on it; next time I will try carrying the Lectric XP.
Thank you for you tip, the motorcycle carrier will definitely work and I have recommended it to other people that only need to transport 1 bike however I’m usually carrying 3 bikes so it won’t work for me!😢.
You did a great job on the demo. Thank you.
Your welcome
Very nice video production as usual.
Thank you I appreciate that.
You keep rocking it Jeremiah!
Good video Jeremioah, but no thank you with the E Bike rack. Too heavy for my back
Really good honest review, facts, and video!
Thank you mark!
My bike weighs 75 lbs. This rack should be ok for my one bike? ❤️
I really wanted to like this rack but it doesn't work on my FJ Cruiser. The part that bends up will block my door from opening because my spare tire is in the way. So for anyone with a rear door that swings open, you'll want to check clearance. That bend that comes up is pretty big and will get in the way. Imho this is best for hatch type doors.
One thing that is important is the quality and grade of the metal throughout. low-grade metal will fatigue. Especially the hook that holds down on the frame, As a precaution, add winch straps for safety. Also as previously mentioned replace the foam hook hold-down pads with rubber. Foam is unacceptable.
I saw that on Amazon and came here to see the review that's what I needed for my bike but I'm concerned if it will hold 3 e-bikes that weight 66 each
I know there has been a few people that loaded the bike rack up with 4 E-bikes on the Lectric Facebook group however I would be very cautious about that and not sure if I would trust it to be honest. It may hold but sometimes I worry about the little things like that lol.
Nice work man, good content
Jeremiah McIntosh, great video. Very detailed and informative. I have been using this rack for a few months now. I have 2 fat tire e bikes that weigh 65lbs a piece. I take out the battery when transporting. Help take off 15 lbs per bike. Heavy duty rack. Do you have anybidea how to stop the side to side wobble? The anti wobble works great for the hitch insert but not the over all wobble coming from the adjustable section.
I just got one for my MTB and families bikes. It is super heavy duty and heavy. I like everything you get with the rack. Was missing end cap and they sent me one right away. Love everything except I wish the hold down bars would rotate making it easier to load and unload the bike without having to tilt the bike.
If you slide the holding bars off then you can bend fold down the middle one and easily put the bike on then fold it back up, that is what I do with my bike because it is around 60 pounds!
Hey Jeremiah, Very informative vid as always. I did found something interesting. I purchased the KAC Overdrive Sports K2. The manual states 60lbs per bike. My Lectric will be mounted on the inside & a lighter bike will be on the outside. I think I'll be fine, this rack is very well built! Cheers!
Thanks for the review. My Lectric 3.0 weighs 64 lbs plus the racks. I notice you mention the manual stats 65-pound capacity. I went online and looked at the manual, which says 60-pound capacity? I was wondering where you sew the higher weight rating. Just want to be safe hauling our 2 Lectric bikes.
It was in my manual but they may have changed it. If you gave the battery’s out you will be under the 60# limit. You can also take the seat out to make it even lighter yet.
This looks like the best of many racks I’ve looked at so far for our Lectric step-thru e-bikes. Thanks for the video review so we can see it in action. How much of little do the bikes wobble (side to side) when driving?
Not to much as long as you have the anti-rattle mechanism tight when installing the hitch.
This is exactly what I need. Thanks for reviewing this rack.
You’re welcome.
@@JeremiahMcintosh Do you think it would hold 2 Electric XP and 2 mountain bikes. According to the spec it should, but I'm not so sure.
I’m not 100% sure but it should. I would take out the batteries and put the heavier bikes closer to the vehicle.
I'm glad Overdrive offered a fat tire version instead of offering the standard version where you would have to drop another $60 on fat tire holders and then you are left with holders you paid for but don't need.
Exactly! And they can be used for skinny tires also! Makes it well worth it in my opinion.
Please explain the difference between the older model rack and newer model rack. You posted links for both models. Thanks
The only difference I’m aware of is the older style like I have has knobs that you turn to tighten on the center hold down clamp and only one locks. The new model has more of a ratcheting style hold down bracket and each one locks.
To be honest I’m not sure which one is better but I would lock the bikes with a heavy chain as well if left unattended.
Hi there, I have a fat tire trike as well as a fat tire bike. Have been trying to find a platform carrier large enough to accomodate both but no luck. I see your multi bike rack here and am wondering if it an be altered for putting a 3 wheel trike on it as well as my bike. Can you offer any assit please?
Hmm I’m not sure. How much does the trike weight?
@@JeremiahMcintosh about 80lbs
great presentation. bought the 2 bike version..
Thank you. In comparison to the price of other fat tire bike racks it’s a good deal.
How do you like it?
So far I like it and haven’t had any problems but I may drill a hole and put a pin in just Incase the swiveling part doesn’t hold.
Hi Jeremiah, great video--very informative! I've asked KAC for a couple measurements, but they can't seem to provide this for me--could you tell me the distance from the center of the second wheel hoop to the center of the fourth wheel hoop, and the distance from the inside edge (nearest vehicle) of the second hoop to the inside edge (to rear away from vehicle) of the fourth hoop? Also, I need 2 measurements on the L-shaped piece of frame that goes into the hitch: what is vertical distance from the top of the horizontal piece of L to the top of the vertical part of the L, and what is the distance from the hitch to the inside of the vertical part? Thanks so much.
Just don’t forget you have 4 bikes on the rack when backing up
Yes for sure...it does stick out pretty far!
How much it hangs backwards, how much more entimeters i lengthens your car with bikes on it and the 4th bike handlebar sticing litle bi out when folded , so overal, in both 1 2 3 and 4 bike modes? could you measure it please?
Jeremiah, do you think this rack will hold and secure Two of the new Lectric XP Step thru models with its lower cross member? Enjoy your videos...very informative!
I’m sure it would hold 2 weight wise but not sure how good it would hold them down being a step through. I plan on getting one and I will make a video on it if I do.
Thank you. We have two Step throughs on order and want to get this rack if possible.
@@JeremiahMcintosh I just checked web site and crossover on step through is 18.5 inches. I sure hope these bikes will fit on the Overdrive rack!
The kid is so cute!
Thanks for the detailed review. It helped make the decision to purchase this on Amazon
No problem you’re welcome. I tried to answer every question I had when I was looking into buying one so I’m glad I could be helpful!
Hello again Jeremiah Great videos you go into a lot of detail on the overdrive 4 bike heavy duty bike rack. And No deafening loud music just plain info and good info
I sent you a comment aprox 22 hours ago on the same rack was wondering if you read it please as asked for a bit more info on the bike rack. Thank you mate. PAUL H ( UK)
Do you know if the company Overdrive sport bike rack for 4 Electric bikes will ship there bike rack too Canada . I just found out they wont ship overseas to EUROPE so annoying.
Thank you! I Just seen it and replied to it.
Ok Great shame they cant be adjusted the other way the distance gap between each bike but thanks for the reply.
Great review, well done. But I don't think the locking mechanism with the square pin that slides into an open slot is good enough. You noticed it too, and made a comment at 3:05 of your video. I'd drill a hole and put a bolt through. I realize the manufacturer wanted a quick way to be able to move the rack, but I see problems on a bumpy road and over time when that mechanism gets worn.
I agree with you and have always been a little skeptical of that however with that being said I have not done anything with mine yet and have been using it with no problems. With a longer trip I would probably consider doing as you suggested with drilling a hole and using a pin or a bolt in it.
Sturdy enough for 2 lectric xp bikes? Seems like its right on the edge of the weight limit especially if you have a few mods on them.
You should not have a problem with 2 bikes on the 2” version it seems very strong however the spring loaded latching pin that keeps the rack from tilting makes me think maybe I should drill and put a pin under just in case it fails and Pops out.
With that being said tho I have not had any problems with it but I’m just a cautious guy lol.
Great review, excellent info. I have a Curt basket cargo carrier. Would it fit in the receiver that is made to connect the extra 2 bike carrier? The Curt basket has a 2” male connection.
Great question. Probably not because the receiver part of the main rack inside dimension is 1 11/16 x 1 11/16 ...outside is 2” x 2” which would be the same as your rack. You may be able to make some kind of adapter out of square tubing to fit in your rack that will fit in this rack kind of like the extender for the four bikes.
👍
Thank you. My Rad Rover is on back order so I am thinking ahead
No problem and hope it helped you out!
Ditto for me!
Unfortunately, my fat-tire e-bike I ordered is 70 lbs., so I'd be over on this weight wise. If/when my wife wants an e-bike, if she gets one like mine, we'd really be over on weight. Looking for extra-heavy duty racks I guess. Thanks for the video Jeremiah...much appreciated!
No problem Dale how about if you take the batteries out are they under 60 pounds then?
Hello Jeremiah, I watcht many of your videos and respect your opinion. I'm asking for your advice. My wife n I are looking for a bike rack for our Lectric XP step through. I have a bad back and we drive a 2007 Toyota Tacoma, can you recommend a durable rack that's not too high off the ground that I can attach to my 2" hitch m?
Do you need it for one bike or two? If you only need it for one bike you might want to check out a motorcycle carrier or something with a ramp.
@@JeremiahMcintosh
I need it for 2 step through Lectric ebikes
After 2 years any update
Jeremiah, Is there an update on whether or not this rack will work for two step through XP 2.0 models?
The only issue I see is the clamps that come down to hold the bikes. you may have to shift one bike to one side or the other for the clamps to come down to hold the bikes if that makes sense or figure out a way to put a top tube bar on for the other clamp to hold the bike. kind of hard to explain but I haven’t really tried it yet with two steps throughs that’s just from my speculation.
Is this bike rack good enough behind an RV motorhome with the E bike
No it is not Rv rated.
Does the bike hold-down hook shown at 5:30 go down low enough to hold your wife's Lectric Step-Through, or did you have to modify it in some way?
Yes it works on the step through. You can see an example of both bikes on this rack in my trail ride video if you would like to check it out.
Thanks!! Will do. Love your videos, so helpful, thorough, informative & personable. Good to see your wife's perspective too. Your son is adorable!
Thank you very much!
Can I attach this to my front hitch ?
I like your review in how thorough it is. I'm concerned with your comment that you can remove the whole rack by removing two bolts. It that only for the last two bikes or for all four? Why is there a key connected to the hitch if you can just remove the whole rack relatively easily. How are the bikes individually secured to the rack? Thanks for your time.
Where the rack folds up on the vehicle there is only one bolt that holds it on there and if you remove that bolt You can basically remove the whole rack. This can be prevented by replacing the bolt with a locking hitch pin or welding the Nutt onto the bolt so that it could not be removed. I’m pretty sure this is probably the same with most bike racks and I recommend using a heavy duty chain lock to lock the bikes to the vehicle if you leave them anywhere unattended.
What platform did you use to edit the GoPro footage in the bike cruise video
I edit all my videos on an iPad Pro with an app called LumaFusion.
Do you think I can put 2 letric bikes on there xp2's
Yes I’ve hauled 2 on it easily.
Do you have a link to the cover you use?
Jeremiah I just bought this rack based on your review.
Awesome and I’m glad you found my video helpful. It has been working well for me. Make sure to use the strap when transporting for extra safety!
I'm planning on using this to haul 4 sewing machines. Do you think it will work? HA! great video!
🤔 hmmm lol
Lol just buy a cargo carrier much cheaper
I think any hitch mounted bike mount will work for an ebike as long as the tires fit properly. The weight should not be a factor as long as the electric bike is mounted closest to the hitch. You can buy a cheap walmart hitch mount for bicycles and a human that weighs 150 plus pounds can stand on the bike rack on the main support beam closest to the hitch. You could not stand on the sides where the tires go of course. I think the weight recommendations are just a safety factor and to keep people from trying to put a heavy dirt bike on a bicycle mount. Old timers would make anything work that they had laying around. The modern generation always wants the best of everything and tries to evaluate every aspect of products and safety. I am guilty of it myself. Not sure if that makes us better or worse than the old timers in the long run. I guess time will tell.
That’s the problem with most fat tires they don’t usually fit unless you buy additional fat tire racks which this one includes. I did not shown in the video but I stood on the back of the hitch when it was all together plus had my ebike mounted up close to the car and it supported me no problem at 160 pounds plus the bike.
However going down the road hitting bumps obviously will put more stress on it but I don’t think it will be a problem at all.
@@JeremiahMcintoshYea, those hitch mounts seem to move around a little in the hitch of the vehicle. I have a regular two bike hitch carrier and the electric bike fits in it fine, the only problem is that the fat tires slide down into where the wheels go. It just makes it a little snug when you go to get it out. Whats the inside width measurement where the tires sit, on that one? I have the two bike Swagman and the inside width is 3 and a half inches. It says it is rated for 35 pounds a bike. I have had the lectric xp and another bike on there and stood on it and it is solid. That is over 300 lbs on the swagman and it does not bend etc. Maybe the companies are being cautious when they tell you that it is only designed to hold a certain weight. I am pretty sure the swagman will hold 500 pounds plus if it is evenly distributed before it would bend.
@Electric Life I have all the measurements in the end of the video that you should need including the width Where the tires go.. hope this helps.
How right you are..!! People spend more time deciding on the latest over-priced cell phone rather than educating their children..!! What a sad state of affairs this country is in....
We have 2 lectric bikes in addition to 2 regular bikes. Is there enough room in between the bikes for all of them to fit?
Yes there is.
How does this bike rack handle speed bumps? Any chance that the rack will fall do the ground while driving?
I would go slow over speed bumps but I have not had any problems with it yet. I would like to add some sort of additional safety pin just for extra security bit I haven’t needed it yet.
I have 3 XP Lectrick bikes what do you think about 3 and a mountain bike do you think it will work?
I think it would work but that’s a lot of weight I would take out the batteries. I personally would be nervous with 3!but I’ve seen photos of others using it with 3-4 Lectric bikes without problems on the Facebook forum.
@@JeremiahMcintosh That's what I was thinking maybe a small trailer would be better thanks.
I would suggest going on the Facebook forum and I think Brian Cohen or some thing is the one that I seen Had a picture with four bikes on the rack maybe ask on there you might be able to get some more opinions.
@@JeremiahMcintosh Thanks but I don't do Facebook
What’s the brand name of rack ? There are tans of In Amazon, can you please give me mor info to buy the rack from Amazon.
The link for it is in the video description.
I would have to install a trailer hitch to my Honda civic hatchback
Thanks for the review...helped me out a lot.
No problem I’m glad it was helpful!
120lbs isn't enough for two Aventon Aventures. For a few $$ more, the Hollywood HR1500 can carry 160lbs.
Will it work with the Lectric step through
Yes it will.
Jeremiah, would this rack work for TWO step thru lectric bikes like your wifes? Thanks
It works good with both of our bikes however we have one of each. The only thing that would be difficult with two step Throughs is the arm that comes down to secure the bikes are two different lengths and the taller one may not come down far enough to hold the tube on one of the step throughs. You might have to figure out how to put some sort of top tube Bar on one of the bikes if that makes sense.
@@JeremiahMcintosh thanks for the very fast response. We purchased two step thrus and are now looking for a carrier. Like you, I dont want to spend as much for a carrier as a bike but still need something strong enough to carry them both. Your vids are the reason we went with Lectric bikes like your wife's. Thanks, Bruce
No problem that’s awesome I’m glad I could help. Like I said it would probably work but you may have to add a top tube bracket like the one I showed and one of my bike rack videos to go from the base of the handlebars to the seat post and then the clamp can hold it down there. Honestly you would probably have the same problem with any bike rack. Some bike racks have the holders that hold the wheels down instead of the bike itself but you might run into an issue with the fenders with that style.
Any idea why the rack can’t be used on RV’s? I have a motorhome.
I have no idea? Maybe it would bounce to much and cause it to break?
Here is a good reason www.etrailer.com/question-224572.html
I specifically didn't buy a fat-bike because range was my primary focus. I wanted to be able to ride 100 miles with a fully loaded (more like over-loaded) tour bike pulling a single wheel suspension trailer. More and more often when I ride on biking infrastructure I see fat-bikes riding in pairs and small groups. I'd love to be able to ride over and through everything they can with 4" tires. The biggest drawback I have seenwith fat-bikes is having to transport them places to ride. I was riding the Foothills trail near Orting, WA and watched a little lady (wife I presume) about 130 lbs. 5'7" unload a fat-bike (her husbands I think) to get to the other fat-bike and then unload it. She lifted the back tire off the stand and drops it to the ground, She squeezes the back brake and pulls back on the bars lifting the front tire up and over the carrier and down to the ground... not even straining. After both bikes are on the ground she opened the back door of the car to grab her water bottle and rode off while a guy sat in the car on the phone the whole time. Ya know... I'm not so sure she was coming back. If those bikes had been in the back of a pickup rather than a low trailer rack I might have had to help her
Bike pics: prior to Oct 2019
photos.google.com/share/AF1QipN67sUw0ykU-Mg5gLsOw9vF8kBMEM5cGCgCNmLT_j72h9iu5fKYFFVbLJ2Z415Umw?key=LUZqdEl1d3RjNV9id0ZvTEFickhITnBwWFZrU3hR
Thank you so much for that detailed description. As a single older woman, I've been debating whether to invest in an e-bike due to doubts about how in the world I would wrestle it on & off a rack. Now I feel confident that I could manage it! Thanks!
@@freedomartwork6950 You are most welcome.
I have a Hollywood rack I really like it really works good
I bought the two fat tire bike version for my 1.5 inch receiver last fall. The rack flops around loosely in the receiver because it arrived without a set screw to tighten the connection. I have scoured the internet for any mention of Overdrive bike racks, but the company does not seem to exist. Amazon also says that the company does not exist either, and offers no warranty support whatsoever. So now I am stuck with a defective product from a non existent company with zero customer support. Does anyone know what kind of screw fastener I need to look for is that will allow me to tighten the bar to receiver connection?
It should of come with a Locking anti-rattle bolt as seen in my video, in fact mine came with one extra one as well. The company you are looking for is overdrive brands and you can contact them through Amazon where it says shipped from and sold by maybe they can send you another one but ultimately if it was missing when you received it you should’ve maybe just returned it and bought another one if they would not send you a new pin.
I’ll see if using a regular pin you may be able to use an anti-rattle mechanism like this amzn.to/2x3KptX
Just keep in mind This is a affiliate link and I will get a small commission if it is purchased through this link which is no extra cost to you. Hope this helps.
HELLO JEREMIAH, VERY GOOD VIDEO on the fat tyre bike rack heavy duty electric bikes , Overdrive sport for 4 bikes. I may purchase this one for a two wheel e bike and a adult European UK tricycle. ( ALPINE EXPLORER ELECRTIC TRICYCLE , in ENGLAND UK and a fat tyre 2 wheeled e-bike like the SONDORS XS FOLD . ) THIS WILL CARRY THE WEIGHT fine if I remove the battery packs. can you tell me if I am able to fix a LIGHT BOARD ON THIS BIKE RACK for tail lights and directional indicators can be seen clearly. this would be fitted onto my RV HERE. AM WAITING FOR some info from the manufacture off the ALPINE EXPLORER TRICYCLE ( its on TH-cam & there website video ) for the distance measurement (gap) between the rear two wheels centre off the tyre to centre off tyre, CAN YOU TELL ME MATE is there any way off adjusting the gap closing it up or widening it off the wheel tray ( wheel holder ) on one bike rack too the other wheel holder on the bike rail. so you can move the bikes further apart or a little closer if needed. PARTICULAR for the centre wheel holder that you showed was only 10.5 inches apart instead off the 12.5 inches gap off the first bike wheel holder. much appreciated thank you kindly Jeremiah. Paul H
No you cannot adjust the distance between the bikes only the distance between the wheelbase of each bike. Hope this helps.
Have you gotten any tickets due to not being able to see your taillights and license plates?
Not yet but I do plan on figuring out a way to mount the plate on the rack for long-distance trips.
Can you put two electric bikes on a two rack
It depends of the weight of each bike and the weight rating on the rack.
Good info to know !
Do you transport bike in inclement weather? If so, how do you protect the electronics? Thanks.
I have not yet but I plan on ordering a cover made for transportation when they come back in stock.
Great presentation, thank you!
Thank you. Your welcome!
The clamps will rub the paint off your bike if your bike has a square tube llike yours has, I have two wallke bikes and took the paint right off
Thank for the heads up. I haven’t had a problem yet but I’ve been keeping an eye on it.
I don't know if there is a non trailer hitch bike rack that can handle the weight of these ebikes.
I doubt it....these ebikes are heavy but this rack seems to hold them well with no problems. Currently the four bike one is on sale for the lowest I’ve ever seen it.
@@JeremiahMcintosh Amazon has got one that is supposed to hold 60 lbs. That is much too close to the weight of the Lectric, less you remove the battery
As I’ve said in the video amazon has it listed as 60lb per bike but the manual states 66lb per bike for the 2” hitch version. But yes you are right about taking the batteries out.
will this type of bike rack hold my ripcurrent s electric bike?
How much does your bike weigh?
@@JeremiahMcintosh about 64 pounds without battery. I was more worried if the rack is long enough. I wanted to get the Overdrive bike rack for the 1.25 hitch.
Oh OK it holds my 63 Pound bike no problem I don’t think you would have an issue with the wheel base but the 1.25” one May not be As sturdy🤔
Great review, thanks
Thanks
Use plummers tspe for small bike
Is this rack rated for tow vehicles?
No I don’t believe it is.Do you mean on an RV?
@@JeremiahMcintosh on our Honda CR-V being towed behind our motorhome.
I’m not sure then in that situation. Maybe 🤔.
Can I fit 2 Lectric e bikes on the rack
Absolutely it will definitely hold 2 Lectric bikes! It is rated for 66 pounds per bike in the manual so no problem for weight or size. I weigh 160 pounds and stood on the rack and it held me just fine.
I carry an XP and the LX on mine, no problem. After 3 months of steady use I'm very pleased with this rack. (And the Lectric bikes also!)
If you use a BBQ cover cant see lic plate
Thanks for your review. I’ll get it from Amazon.
NIce. Thanks
Covering up the license plate is just another reason for the police to stop you... also covering up the bikes with a tarp can block your tail lights... this is a problem with all the hitch racks
LOL I wouldn’t cover up the license plate while driving down the road but good point on the grill cover ...I did not think about it covering the tail lights. 🤔
@@JeremiahMcintosh Take another look at your set-up.....you are covering your plate location..Lol... you can't have anything in view of your plates... not even a hitch ball if it block the plate... its a reason to be stop.
I have the same problem with my 1up-usa rack... I have to relocate my plate to the back of the rack. If I fold down the seat and handlebar I'll be okay with the lights if I have the cover on.....I don't want to be rear-ended. Here in the State of California you can't have any type covering your plates. That included the smoke or clear plastic protector... even if they sale it in the local part store. They get really strict because of all the toll bridges and lanes....also the red light camera. To make this all legal you also have to have a license plate light....... It just doesn't stop to have everything legal
Damnit why cant I find a rack like this for 300 bucks
Lol they were way cheaper when I bought mine 2 years ago.
@@JeremiahMcintosh btw great detailed video 👍
Thank You I appreciate that!
Nice but your hitch has severe rust
On Amazon it says "RV use prohibited", so it's no good to put behind my motorhome. Nice video otherwise, thanks.
Most bike racks are not rated for rv use.
Hollywood bike racks say the same thing but specify, not on towed RVs. Motorhomes and B vans are OK. I'm sure these would be the same.
@@jima28080 Thank you.
This kind of defeats the purpose of having a folding bike. In that case you can get a non folding model that's maybe a bit nicer than this one
That was my thinking also before I bought mine....Why wasn't there a rack out there where you can fold-up your bike and put it on a rack.
You are absolutely correct but if you need the extra storage space when you’re going on a trip is nice to have the option to transport it externally as I said in the video. I doubt you’ll find a nicer bike for A comparable price of the lectric though. Or if you’re transporting other bikes that are not foldable like I will this is a great rack because you can use it for both.
@@JeremiahMcintosh Amazon and Lectric could use you as a spokesperson, you are very convincing and likable.
@J Hunt Actually you could probably use It with a cargo carrier ...fold your bike up put it in a tote and strap it to that however I needed something that was going to carry my families bikes as well.
@pedro fernandez Haha well thank you I appreciate that! I am very frugal when purchasing things and tend to research my purchases prior to buying that’s why I like to share my experiences with items I purchased to help other people out especially with questions I had that I could not find the answers to.
You no the cops can give you a ticket for obstruction to the car tag
Rv use prohibited 🚫
Most hitch racks are.
@@JeremiahMcintosh many ebike owners are RVing so just wanted to make sure they were aware
Great review, thanks