Powrtouch Classic Motor Mover: Cover removal & bearings etc.

แชร์
ฝัง
  • เผยแพร่เมื่อ 24 ธ.ค. 2024

ความคิดเห็น • 20

  • @MsInlovenow
    @MsInlovenow 2 หลายเดือนก่อน +2

    This is exactly the video I needed to find. Thanks

  • @jimmystobbart6968
    @jimmystobbart6968 หลายเดือนก่อน

    I’m trying this tomorrow so this has been very helpful!!!

    • @MrRichardmorris
      @MrRichardmorris  หลายเดือนก่อน

      @@jimmystobbart6968 good luck - and expect to get grubby!

  • @colsuemeg
    @colsuemeg 5 หลายเดือนก่อน +1

    Thank you so much for making this video. I followed Powrtouch instructions for removing the cover, they never mentioned doing what you did. Now I know. Thank you. 👍👍👍

  • @moxymagic
    @moxymagic 10 หลายเดือนก่อน +2

    This is a job that I need to do but had no idea how to go about it , thank you for posting this.

  • @WayneHellewell
    @WayneHellewell 4 หลายเดือนก่อน

    Hi Richard, excellent video and thank you. However a question if I may. I need to replace the inner and outer bearings but removing them is not easy, any tips?

    • @MrRichardmorris
      @MrRichardmorris  4 หลายเดือนก่อน

      Glad you found the video useful. I used lots of WD40 and different screwdrivers. Firstly I used a levering action between the roller and the bearing, then as it opened up a bit a twisting action and finally a chiselling action with a light hammer and broad screwdriver - always rotating the shaft after each strike so the bearing didn’t bite into the shaft. I may have been lucky and guilty of tool abuse!

  • @rawiriadair9595
    @rawiriadair9595 5 หลายเดือนก่อน

    Glad i came across you.
    I was operating lever to engage movers,
    Heard a bang on the other mover,
    Now its stuffed.
    I undone hexagon bolt and thought the cover would come off.....
    Oh no no no!!
    Because of you , i now know,
    So simple.
    Do tomorrow i van investigate the broken!?!? Internal part.

    • @MrRichardmorris
      @MrRichardmorris  5 หลายเดือนก่อน

      @@rawiriadair9595 good luck - prepare to get dirty crawling under the caravan and then encountering all the grease!

  • @ste118sa
    @ste118sa 8 หลายเดือนก่อน +1

    Hi great video I'm fitting one of these to my caravan now I'm just wondering how big is the gap between the motor mover and wheels before it is engaged thanks

    • @MrRichardmorris
      @MrRichardmorris  8 หลายเดือนก่อน

      This link will show you the different values based on model number: www.powrtouch.com/roller-gap-adjustment/
      Hope that helps- and good luck!

  • @cq44b
    @cq44b 8 หลายเดือนก่อน

    Great video Richard, I’ll drop my van of later for new bearings.❤

  • @tom42n
    @tom42n 6 หลายเดือนก่อน +1

    Helpful video, many thanks.

  • @neilglover2969
    @neilglover2969 8 หลายเดือนก่อน

    Very helpful Richard. Thank you.

  • @themorfill
    @themorfill 5 หลายเดือนก่อน

    How did you remove the roller?

    • @MrRichardmorris
      @MrRichardmorris  5 หลายเดือนก่อน

      Hi - you can only remove the roller by completely dismantling the mover. There is a bolt through the gear inside the housing through into the end of the roller so you can never just pull/wack it out after removing the “3 bolt” roller end cover. Does that answer your question?

    • @themorfill
      @themorfill 5 หลายเดือนก่อน

      @@MrRichardmorris yes. I had it dismantled, it just needed a couple of whacks with a hammer to get the spline of the roller to release. 👍 Thanks.

    • @MrRichardmorris
      @MrRichardmorris  5 หลายเดือนก่อน

      @@themorfill Brilliant!

  • @daleaxe1030
    @daleaxe1030 10 หลายเดือนก่อน

    Thanks pal 🎉