Simple Touch Free Automatic Hand Sanitizer Dispenser
ฝัง
- เผยแพร่เมื่อ 19 พ.ค. 2020
- Hi friends, as you are aware of the current situation around the world. i have made this Simple non-contact sanitizer dispenser so that one bottle of sanitizer can be used by many persons.
this is a simple and easy to do project. for which you will require the following parts:
Arduino UNO
HC-04 Ultrasonic Sensor
SG90 Servo motor
9v Battery and Cap
some jumper wires
Link for Code: drive.google.com/file/d/1KuEA...
Schematic: drive.google.com/file/d/1qykU...
Solder Iron i Use: bit.ly/2GSArih
Helping Hand Magnifier: bit.ly/2Uh11oe
arduino uno Micro USB: bit.ly/aRdUiNo
also do check out these cool 3d Printers:
Creality Ender 3 pro : bit.ly/36m1POI
Creality CR-10s pro: bit.ly/2QmqU6z
#SanitizerDispenser #Arduino #Project
super!
Love you 😘
love u you are a very nice youtuber keep doing your job and i will tell people about you
Thank you so much 😀
@@SuperbTech we have to connect the battery and motor at the same point ??
how to code ultrasonic sensor so that it detects first instead of loop
bro wiring diagram link is not in the description
Bro we need power source for the aurduino board .. otherwise the servo motor will not work
Can't open the code link. Please update
Are hc 04 and hc sr04 same
how to connect the battery with the arduino?
Hey bro the link dosent open
Please make it Wireless
Bro the schematic is incorrect, how can u give 9v supply from battery to Vin Pin and also take supply from.same.pin and give to motor? And what you have done in video is different from what is in the schematic.
I can't open the code😢
We cant oepn the code
my servo motor is working but not coming again my servo motor
Ultra sonic sensor cost
Please tell me code link not opening
Can u pls state the code here?
HCSR04
Pump motor
Led
Resistor 330 ohm
Relay(5v) 1dənəli
Aurdino (nano)
Can I use Arduino nano for this.
Sure you can
What application do you use for coding?
Arduino i.d.e
What's the code?
Hey sir, code doesn't open😭😭😭
Code please
Bro send me the code please bro
bro wiring diagram not in description, pls provide it...tq
i have updated
this is the code
Guys i have the code
It is working for me
may i have the code? if you dont mind to share
Can you pls share the code?
can i get the code
can i get code pleas
Bhai code dado yrrr chaya kasa
Send me arduino diagram
It’s in the description
Dude it broke my servo because u short your 9 volts to servo motor wtf
Update your BS SCHEMATIC SHEESH
What should be it?
@@darkcookie2457 what are we supposed to do ?
Bro please send me the code
Please bro
Bro please
Bro please
Bro please
Sorry
Khaby📞
the schematic is bad connected
Guys this is the code:
I first opened it in PC with notepad then i copied it and WhatsApped to my phone
#include
const int trigPin = 10;
const int echoPin = 11;
long duration;
int distance;
Servo myServo;
void setup() {
// put your setup code here, to run once:
myServo.attach(12);
pinMode(trigPin, OUTPUT); // Sets the trigPin as an Output
pinMode(echoPin, INPUT); // Sets the echoPin as an Input
Serial.begin(9600);
}
void loop() {
// put your main code here, to run repeatedly:
distance = calculateDistance();
myServo.write(0);
if ( distance < 5)
{ myServo.attach(12);
myServo.write(160);
delay(500);
myServo.write(0);
delay(1000);
}
else{
myServo.detach();
}
Serial.println(distance);
}
int calculateDistance(){
digitalWrite(trigPin, LOW);
delayMicroseconds(5);
// Sets the trigPin on HIGH state for 10 micro seconds
digitalWrite(trigPin, HIGH);
delayMicroseconds(10);
digitalWrite(trigPin, LOW);
duration = pulseIn(echoPin, HIGH); // Reads the echoPin, returns the sound wave travel time in microseconds
distance= duration*0.034/2;
return distance;
}
Bro send me the code please bro
Bro send me the code please bro
Bro send me the code please bro
Bro send me the code please bro
Check description
It's curropted