You made a mistake in connecting the pump to relay, you connected it to NC then pump stops only when we show our hands to ir sensor. I know you realized it and changed it to NO but why don't you mention it in the video?
Hi, Thank you for bringing this to our notice. There is a minor connection correction performed in the video. However the lable on screen at 6:05 indicates the correct connnections to be made which should be followed.
It depends on the solenoid pinout. If the solenoid can be triggered using a 5V signal, then the same circuit can be used and the relay can be replaced with solenoid
Hi, have you tuned the IR sensor, it has a small potentiometer on top that can be used for tuning , ensure that it turn on only when you get your hand close to it
Hi, If you wish to use a switch as a master override to turn the dispenser off, you can add it between the VCC (red wire) from the adapter and the VCC junction that goes to the motor and sensor.
This video really helps, thanks! I made this but whenever I try to put the battery, it automatically starts pumping; however after that it functions normally. Can you tell me what the problem is?
Hi Prabhat, The adapter and relay used are 5 volts, hence a 9v battery cannot be used. You may howver use a voltage regulator to step down the 9v to 5v. A circuit built using the 7805 voltage regulator may help you.
Yes! As long as all your parts work with 9V safely (the motor, relay, IR module). You should be good to go. Otherwise you will need a way to step down 9V to 5V using buck modules
Hello, There might be some issue with the connection. The positive pin of motor or pump is connected with the NO pin of the Relay and the negative pin of the motor or pump is connected with the negative pin of the DC jack.
I am 3rd year b.tech student I selected this project as mini project But for me the relay is not triggering when hand is placed in front of ir sensor. Please tell me what will be the issue.
@@helalali6555 Since there is the addition of Arduino to the existing components in the kit, it will not be cheaper to use Arduino, however, if your application has additional requirements such as use of more sensors, LEDs, actuators etc. then it would be advisable to use an Arduino since it is easier to control those using a microcontroller
Friend my project is going just opposite, when objects comes in contact with sensor then motor stopes and when the object removed the motor start working
Hi Nitin, Please check the second last paragraoh in the video description. If the system is behaving differently, the steps given in the description may help you.
Sir Mera ir sensor ki red light glow ho rahi hai par jab me hat aage le ke ja raha hu tho work nahi ho raha hai red light hi hai. Mene ir sensor ke blue part ke up me gumaya plz hel
Hi, You can find the kit for this project here: www.robocraze.com/diy-automatic-sanitizer-dispenser-kit Using Arduino depends on your requirement and budget. This dispenser can be made without using Arduino as demonstrated in this video. However, if you wish to modify the system to include more sensors, LED's or any other peripheral which requires a microcontroller, then you could use an Arduino since its a low-cost microcontroller.
How do u get active high output on IR module? All Chinese modules have active low o/p. They give high when no obstacle and low when detected obstacle. Something is wrong or missing!
Hi, The sensor that ships with the kit is active high, hence it can be used in the configuration as shown. If you happen to have an active low sensor, you could work around this issue by connecting your pump to the NC pin of the relay.
To clarify the circuit once, this setup requires 4 sets of connections. These are as follow: 1. VCC from adapter -> VCC of relay module, VCC of proximity sensor and NO (normally open) pin of relay 2. GND from adapter -> GND of relay module, GND of proximity sensor and GND of pump motor 3. Output of proximity sensor -> input of relay module 4. Positive terminal of pump motor -> COM pin of relay module For more information refer our blog: www.robocraze.com/blog/post/automatic-sanitiser-dispenser
Hi Syed, Please find our blog in the link given below. Here you can find the circuit diagram along with additional information about this build. www.robocraze.com/blog/post/automatic-sanitiser-dispenser
Sir you are going great but you must create a circuit diagram so that if someone didn't understand your language or connections in the video so he/she can refer the circuit diagram for their project Thank you ❤️
Hi, Please try powering your pump motor directly to see if it is faulty or not. If the motor powers on when conected to supply directly, there may be a problem with your connections.
If the sensor have a diode(LED) on the module then you can directly check its working just by giving power supply and checking if the LED status changes according to your requirements.
You can use ultrasonic sensor if you have a controller such as the Arduino. Without controller, it is not really possible as the a microcontroller is required to calculate the distance between pulses emitted by the sensor itself
But.... Sir in last u cut the video....? .... Bcaz there is fault in your connection.... Thus why....The relay Start in low signal.... Pls sir make a full live video without any editing.... Otherwise... Ur video explanation is very... Gud... But my Project is not working with this circuit....
Hi, To clarify the circuit once, this setup requires 4 sets of connections. These are as follow: 1. VCC from adapter -> VCC of relay module, VCC of proximity sensor and NO (normally open) pin of relay 2. GND from adapter -> GND of relay module, GND of proximity sensor and GND of pump motor 3. Output of proximity sensor -> input of relay module 4. Positive terminal of pump motor -> COM pin of relay module Hope this clears things up For more information refer to our blog: www.robocraze.com/blog/post/automatic-sanitiser-dispenser
Hi, The relay is to control the power to the pump. We need the pump to turn on and off based on the output of the proximity sensor. The output of the proximity sensor is connected to the input of the relay. The output of the proximity sensor in itself is insufficient to drive the pump.
Hi Beena, Please find our blog in the link given below. Here you can find the circuit diagram along with additional information about this build. www.robocraze.com/blog/post/automatic-sanitiser-dispenser If you are facing any other issues with the circuit, do let us know.
We dont give free samples, but you can use the coupons on our website to avail discounts. robocraze.com/deals/ For any further asssitanace, please reach out to us via website chat.
Yes, a phone charger can be used as a power supply if it meets the required rating of 5V 1A. However, exercise extreme caution while making connections so as to not cause any damage to the phone charger.
Hi Sneh, Please find our blog in the link given below. Here you can find the circuit diagram along with additional information about this build. www.robocraze.com/blog/post/automatic-sanitiser-dispenser
Hi, Please check the steps given in the description of this video to ensure your potentiometer settings and connections are correct. We have discussed these issues in the description.
You made a mistake in connecting the pump to relay, you connected it to NC then pump stops only when we show our hands to ir sensor. I know you realized it and changed it to NO but why don't you mention it in the video?
Hi,
Thank you for bringing this to our notice. There is a minor connection correction performed in the video. However the lable on screen at 6:05 indicates the correct connnections to be made which should be followed.
This is so cool. Explained really well.
Thanks! :)
Hi Saakshi,
We are glad you liked this tutorial. Do subscribe for more such cool projects :)
How many volt is the adapter
Is it work with phone charger
Regualr 5V 1A adaptor will work. Yes, most phone chargers will work, but do note that you will need to cut the wires
@@Robocraze thank you ok
can you make a wiring diagram?
How to set particular quantity to dispense?
You will need a timer module for this. Check this video th-cam.com/video/LBafrZd6Pbw/w-d-xo.html
Superb sir
We are glad you enjoyed this video. Do check out the other videos on our channel for more cool ideas! :)
Can I do this with a 12v relay ??
You can, but ensure all your other components are also rated for 12V
How did u open up the middle of the wire?
You can use a wire stripper or wire cutter to strip out the insulation
I tried using a 9v battery, why doesn't it work? do you really have to use 3.7v?
What kind of relay module you are using in your video?
Hi Amatya,
In this video, a regular 5v relay module has been used.
I'm getting a problem pls help mine relaymodules both light glows but light on ir sensor doesn't glows pls help
Hello,
You can try adjusting the potentiometer and then check it out.
Thank you
Sir, how long will it take for the product to be delivered if we order the kit which is mentioned in the video description???
We ship all orders within 1 Working Day.
Is it okay to use 6v adapter but the single jumper delay module is 5v?
It is not recommended to use a source voltage higher than the component's voltage rating as it might end up damaging the device
Sir please explain how the adaptor is connected in the end...my project is incomplete...help me out please
The adapter is connected to the jack splitter. GND is taken as common and the VCC is passed through the relay to control on/off.
Can the IR sensor handel 12v 500ma voltage constant from an adaptor? I wonder because the load is low.
Hi,
The adapter being used in the video is a 5v 1A adapter. A 12v adapter will not work since the IR module requires 5v VCC.
Is soldering required?
Soldering is not required for this project
What's the input power supply
Hi,
In the video, we have used a 5v 1A DC adapter.
What changes will I have to make if I want to add a solenoid (SV) please tell
It depends on the solenoid pinout. If the solenoid can be triggered using a 5V signal, then the same circuit can be used and the relay can be replaced with solenoid
Hello its not working dude all 2 lights of relay is glowing when pull wire from relay and then motor is working without sensor
Hi, have you tuned the IR sensor, it has a small potentiometer on top that can be used for tuning , ensure that it turn on only when you get your hand close to it
Robocraze yo now it’s working
Hi there, if I was to add a switch to the circuit to turn it on and off. Where would I add the cables?
Hi,
If you wish to use a switch as a master override to turn the dispenser off, you can add it between the VCC (red wire) from the adapter and the VCC junction that goes to the motor and sensor.
Perfect, thank you so much.
We are glad this helped you. Do leave a like and subscribe to get more such content :)
How to add cut off in this??
It automatically cuts the circuit off using relay when the hand is not in front of the proximity sensor
Can i use 9 v battery
Hello,
The relay and the sensor work on 5v. so a 9v battery wouldn't directly work.
Thank you
This video really helps, thanks! I made this but whenever I try to put the battery, it automatically starts pumping; however after that it functions normally. Can you tell me what the problem is?
Same problem
Hello, It could be happening because any obstacle is getting detected while you put the battery.
Can I use 9V battery instead of DC connector
Hi Prabhat,
The adapter and relay used are 5 volts, hence a 9v battery cannot be used. You may howver use a voltage regulator to step down the 9v to 5v. A circuit built using the 7805 voltage regulator may help you.
@@Robocraze Thx for the Help.
@@prabhatsharma8958 Glad we could help you. Do drop a like and subscribe and stay tuned for more cool projects :)
Nicely explained bro
Thank you, we are glad the tutorial was helpful to you :)
Can i connect 9volt battery
Yes! As long as all your parts work with 9V safely (the motor, relay, IR module). You should be good to go. Otherwise you will need a way to step down 9V to 5V using buck modules
Sensor is not working🙁 Plz help
Hi, which sensor are you talking about? If you purchased from Robocraze, please contact tech@robocraze.com to help you with your project
@@Robocraze I've purchased from Amazon. Earlier I was working fine but now it has stopped working
Thanks.
You're welcome
Sir mera ak project hai lakin humse ir sensor or realy se motar nahi chal raha hai please help me
Hello, please raise a ticket on support.robocraze.com with your detailed query and images, and our team will get back to you at the soonest!
With out motor relay is working on and off but if connet motor close the sensor not off if remove hand why bro
Hello,
There might be some issue with the connection. The positive pin of motor or pump is connected with the NO pin of the Relay and the negative pin of the motor or pump is connected with the negative pin of the DC jack.
Such a good project!!
Thank you, we are glad you enjoyed the video. Please like and subscribe for more such content.
When connect the motor always on..
If not connect motor relay working good why
Hi, we will need more information to help you out with your issue
Sir mainay battery use kari iski light nay battery khatum kerdi led light was continuously on.
Hi,
The LEDs can be desoldered to reduce power consumption or can be supplied with power from an adapter.
I am 3rd year b.tech student
I selected this project as mini project
But for me the relay is not triggering when hand is placed in front of ir sensor.
Please tell me what will be the issue.
The issue can vary from relay module not working to connections being incorrect. We will need more information to help you out better
Cool man
Thank you, we are glad you enjoyed the video. Please like and subscribe for more such content.
Gracias amigo un suscriptor más ..
Sir can i get the circuit diagram of the connection ?
Please check the description where we have linked the blog post with circuit diagram on our website
Awesome Awesome Awesome
Thank you, we are happy that you liked the video. Please like and subscribe to not miss our new videos.
@@Robocraze sir it will cheaper than arduino can u please answer?
@@helalali6555 Since there is the addition of Arduino to the existing components in the kit, it will not be cheaper to use Arduino, however, if your application has additional requirements such as use of more sensors, LEDs, actuators etc. then it would be advisable to use an Arduino since it is easier to control those using a microcontroller
Friend my project is going just opposite, when objects comes in contact with sensor then motor stopes and when the object removed the motor start working
Hi Nitin,
Please check the second last paragraoh in the video description. If the system is behaving differently, the steps given in the description may help you.
Sir Mera ir sensor ki red light glow ho rahi hai par jab me hat aage le ke ja raha hu tho work nahi ho raha hai red light hi hai. Mene ir sensor ke blue part ke up me gumaya plz hel
Hello,
You can try adjusting the potentiometer and then check it out.
Thank you
Bro i want to know how its costed to you?? And 1 more questions if i use arduino which would be cost effective?
Hi,
You can find the kit for this project here: www.robocraze.com/diy-automatic-sanitizer-dispenser-kit
Using Arduino depends on your requirement and budget. This dispenser can be made without using Arduino as demonstrated in this video. However, if you wish to modify the system to include more sensors, LED's or any other peripheral which requires a microcontroller, then you could use an Arduino since its a low-cost microcontroller.
How do u get active high output on IR module? All Chinese modules have active low o/p. They give high when no obstacle and low when detected obstacle. Something is wrong or missing!
Hi,
The sensor that ships with the kit is active high, hence it can be used in the configuration as shown. If you happen to have an active low sensor, you could work around this issue by connecting your pump to the NC pin of the relay.
One more thing. Relay has arcing issue which can be very dangerous in case of alcohol based sanitizer. It can trigger an explosion.
@@Robocraze can you help with this wiring diagram of connecting
motor to NC
To clarify the circuit once, this setup requires 4 sets of connections. These are as follow:
1. VCC from adapter -> VCC of relay module, VCC of proximity sensor and NO (normally open) pin of relay
2. GND from adapter -> GND of relay module, GND of proximity sensor and GND of pump motor
3. Output of proximity sensor -> input of relay module
4. Positive terminal of pump motor -> COM pin of relay module
For more information refer our blog: www.robocraze.com/blog/post/automatic-sanitiser-dispenser
You can give the diagrame?It would be usefull.Please help me,
Please find the connection diagram in the blog here: robocraze.com/blog/post/automatic-sanitiser-dispenser
Ok bro I trying this,Thank you bro❤
Very nicely done 😊👍
Thank you, we are glad you enjoyed the video.
i buyed this project on ur website
i m not able to understand the wiring can u plz give me WIRING DIAGRAM...
REGARDS
Hi Syed,
Please find our blog in the link given below. Here you can find the circuit diagram along with additional information about this build.
www.robocraze.com/blog/post/automatic-sanitiser-dispenser
Sensor ko adjust how to
Sensitivity can be adjusted with the onboard potentiometer
Sir you are going great but you must create a circuit diagram so that if someone didn't understand your language or connections in the video so he/she can refer the circuit diagram for their project
Thank you ❤️
Please check the video description for a link to the blog post containing all the necessary circuit diagrams
Motor pump not work
Hi,
Please try powering your pump motor directly to see if it is faulty or not. If the motor powers on when conected to supply directly, there may be a problem with your connections.
Mera ir sensor on hi nahi hora
Same connection hi mene kiye he 😔
If the sensor have a diode(LED) on the module then you can directly check its working just by giving power supply and checking if the LED status changes according to your requirements.
Can we use ultrasonic sensor In the place of IR sensor
You can use ultrasonic sensor if you have a controller such as the Arduino. Without controller, it is not really possible as the a microcontroller is required to calculate the distance between pulses emitted by the sensor itself
But.... Sir in last u cut the video....? ....
Bcaz there is fault in your connection.... Thus why....The relay Start in low signal....
Pls sir make a full live video without any editing.... Otherwise... Ur video explanation is very... Gud...
But my Project is not working with this circuit....
"Hello,
We appreciate your feedback, and we will certainly take your input into account to enhance the quality of our upcoming videos. Thank you!"
Every thing is good but connections are very confusing.
Hi,
To clarify the circuit once, this setup requires 4 sets of connections. These are as follow:
1. VCC from adapter -> VCC of relay module, VCC of proximity sensor and NO (normally open) pin of relay
2. GND from adapter -> GND of relay module, GND of proximity sensor and GND of pump motor
3. Output of proximity sensor -> input of relay module
4. Positive terminal of pump motor -> COM pin of relay module
Hope this clears things up
For more information refer to our blog: www.robocraze.com/blog/post/automatic-sanitiser-dispenser
@@Robocraze Thank you very much for solving my issue and replying fast 🙏
We are glad this helped you. Do leave a like and subscribe to get more such content :)
Relay nahi lagate fir bhi kaam karta hai IR Sensor, fir relay kyo lagaya aap ne ?
Hi,
The relay is to control the power to the pump. We need the pump to turn on and off based on the output of the proximity sensor. The output of the proximity sensor is connected to the input of the relay. The output of the proximity sensor in itself is insufficient to drive the pump.
not working
please help
Hi Beena,
Please find our blog in the link given below. Here you can find the circuit diagram along with additional information about this build.
www.robocraze.com/blog/post/automatic-sanitiser-dispenser
If you are facing any other issues with the circuit, do let us know.
I want an free sample from you please give a link.
We dont give free samples, but you can use the coupons on our website to avail discounts. robocraze.com/deals/
For any further asssitanace, please reach out to us via website chat.
5v and single ampere means 5v& 1 ampere ...and also can we use any phone charger as adapter???
Yes, a phone charger can be used as a power supply if it meets the required rating of 5V 1A. However, exercise extreme caution while making connections so as to not cause any damage to the phone charger.
Not working, share your complete circuit diagrams
Hi Sneh,
Please find our blog in the link given below. Here you can find the circuit diagram along with additional information about this build.
www.robocraze.com/blog/post/automatic-sanitiser-dispenser
Mere sensor ki dono lights jal rahi hai.... Aur current pass karte hai toh bina kuch saamne laye hi pani aana start ho jaata hai... PLZ HELP ME 😩😩
Hi,
Please check the steps given in the description of this video to ensure your potentiometer settings and connections are correct. We have discussed these issues in the description.
Please sir help kijye 😭😭😭
Hello, please raise a ticket on support.robocraze.com with your detailed query and images, and our team will get back to you at the soonest!
Bhai hindi m kyu nhi bolte hooo...circuit diagram bhi show karte
Hi,
Please check timestamp 6:05 for motor connections. They are mentioned on the screen.
you do know that sanitizer is flammable, right?
The sanitiser itself is not in contact with any of the electrical components apart from the pump - which is designed to be submersible.
@@Robocraze yes, they do. That kind of diaphragm pump is notorious for being leaks. Once it does, it can cause somebody their life.
@@Robocraze i hope you understand what i was saying about LEAK. That cheap diaphragm pump is NOTORIOUS for leaking. can you comprehend my statement?
this is just a small project so daddy chill
@@ifhami4122 small project that can cost someone's their life? Are you nuts?
Please give me the kit for free 😭😭😭
Wish we could do that. But we have a lot of coupons available. Check out on www.robocraze.com
Please give me a coupon link
@@Odiadunia-m3e robocraze.com/deals/
I want the automatic sanitizer kit for free