My money is on that butterfly nut needing to be 1 notch tighter, and when you replaced the plate you cranked her down better.. Mark the nut with a scratch, and the plate with a scratch so you can align them when removing and reinstalling. Then count your rotations so you restore it to the same specs. That plate to me looks like it still have plenty of life left on it. Hit it with some sand paper to increase it's friction but otherwise it looks fine. Cheers
Question I'm trying to get my started but it won't let me paddle...I'm pulling the clutch lever all the way back and it's still won't engage.what can I do
Im at the same place. Bike runs fine when going but does not go from a dead stop. I was going to start tightening the flower nut, but after watch ing, I'm trying to restore some friction by drilling a tiny bit into all those square holes on the clutch plate or marking some grooves in it with a heavy file. I can always just buy the plate.Thanks for the video.
Kinda having this problem. I replaced the pads it was good for a week then as the pads wore out a little it needed adjusting again and again but it got to the point it was good to ride. One day I was riding and realised I was getting uneven clutch wear. The only thing I can see that needs replacing is that friction plate since around the edge there’s a spot where it’s smoothed out where it’s got so hot most likely. So do u think replacing that friction plate will solve my issue? If so please send a link to where I can get one
and after I put the chain on it won’t roll the tire when I try to roll the bicycle the back wheel just locks up and what’s to slide on the ground how can I fix that and when I flip the bike over and move the wheel it wants to act like it’s going to start but when I put it on the ground it just skid on the ground
@@ihmaelx9187 A couple things you could try: 1) be sure you're getting a decent amount of speed before you release the clutch 2) check your wired connections as a faulty connection to the CDI is a likely culprit to a no start/no sound issue 3) make sure your spark plug connector is good and making adequate contact with the plug (mine came broken out of the box and I had pretty much the same issue you're describing. A cheap (and much better) replacement can be found at your local auto parts store.
I got a comment maybe able to help me okay mine's different I'll pull in the clutch and the handle thing up there and I'll push the motor while the bicycle Ford and backwards and will not out gauge where the tire just turned freely where I ain't trying to turn the motor would you know anything about that or if you knew somebody to send me if you send me a link on it or something I appreciate it thank you have a good day sir
Dude thanks I was trying to figure out so many things and never thought about the clutch plate because had just gotten it thank you!
My money is on that butterfly nut needing to be 1 notch tighter, and when you replaced the plate you cranked her down better.. Mark the nut with a scratch, and the plate with a scratch so you can align them when removing and reinstalling. Then count your rotations so you restore it to the same specs. That plate to me looks like it still have plenty of life left on it. Hit it with some sand paper to increase it's friction but otherwise it looks fine. Cheers
Thank you so much I did this and it worked like new
Same problem I'm having I appreciate it im gonna try to swap my plate and pads out with my other bike clutch
Tell me if it works!
did it work
my motor is brand new and when i pull the clutch it do nothing
Adjust your flower nut under clutch cover
@@tokenkingg3528tighter or looser?
Mine is used, but i have a brand new lever and messed with the lever and rod, but it never worked imma buy a new clutch
I’m having trouble with my bike when I’m riding and go to pull in the clutch so it can idle it just cuts off any ideas of wats wrong with it ?
Question I'm trying to get my started but it won't let me paddle...I'm pulling the clutch lever all the way back and it's still won't engage.what can I do
Same with mines
Mine is doing the same thing
Update?
@@Dummymanloll Update?
@@ttomyking28 update?
What do you do if the clutch plate is at an angle
I have a hard time pedaling I have to have someone push me to start my engine what do I do
Im at the same place. Bike runs fine when going but does not go from a dead stop. I was going to start tightening the flower nut, but after watch ing, I'm trying to restore some friction by drilling a tiny bit into all those square holes on the clutch plate or marking some grooves in it with a heavy file. I can always just buy the plate.Thanks for the video.
Kinda having this problem. I replaced the pads it was good for a week then as the pads wore out a little it needed adjusting again and again but it got to the point it was good to ride. One day I was riding and realised I was getting uneven clutch wear. The only thing I can see that needs replacing is that friction plate since around the edge there’s a spot where it’s smoothed out where it’s got so hot most likely. So do u think replacing that friction plate will solve my issue? If so please send a link to where I can get one
I’ve replaced the friction plate and still nothing, still have the same problem
and after I put the chain on it won’t roll the tire when I try to roll the bicycle the back wheel just locks up and what’s to slide on the ground how can I fix that and when I flip the bike over and move the wheel it wants to act like it’s going to start but when I put it on the ground it just skid on the ground
Are you squeezing the clutch lever when you try to move the bike?
@@bloatedpotato this shi happening to me when I let go of the clutch the tire just skids on the floor no engine sound no piston sound nothing
@@ihmaelx9187 A couple things you could try: 1) be sure you're getting a decent amount of speed before you release the clutch 2) check your wired connections as a faulty connection to the CDI is a likely culprit to a no start/no sound issue 3) make sure your spark plug connector is good and making adequate contact with the plug (mine came broken out of the box and I had pretty much the same issue you're describing. A cheap (and much better) replacement can be found at your local auto parts store.
So my bikes letting me go without holding the clutch in idk how I get the clutch to be engaged again
Tighten the clutch flower
loosen the nutt loosen the clutch cable that worked for me
I got a comment maybe able to help me okay mine's different I'll pull in the clutch and the handle thing up there and I'll push the motor while the bicycle Ford and backwards and will not out gauge where the tire just turned freely where I ain't trying to turn the motor would you know anything about that or if you knew somebody to send me if you send me a link on it or something I appreciate it thank you have a good day sir
Anyone know how to trouble shoot back wheel getting stuck?
I have the same problem you gotta align the back wheel with the chin
Oh I forgot it's a 70cc 2-stroke
Don’t see how that plate could wear out
What’s the discord?
Hey motorized sexy my clutch is not disabled some reason I need help I replaced everything