Great video. What kind of a relay did you use? I purchased a 12 Volt Automotive relay and it won’t work. The condenser fan runs on 9 volts and once energized the voltage drops to 4. Also the board is not able to see the operation of the new compressor. Getting 3 flash codes. Any ideas? Thank you.
Excelente video pero tengo un problema. El abanico tiene 4 cables y tiene 12vdc constantemente. Cuando se apaga el condenser fan todavía tiene 12v y por esa razón no se apaga el compresor. Tiene algún arreglo para eso? Gracias!
I do not believe that the use of conventional compressor instead of linear one work as expected, because the linear compressor does not work with ON OFF control temperature, it works with incresasing or decreasing the speed depending of thermal load inside the frige. So when you use a realy taking the PWM signal of feedback signal from Condenser fan just stopping the conventional compressor when defrosting process starts.
did the amount of refrigerant needed change? my swap is only getting into the 40s frdge/20s freezer (f). once it gets this low the lowside goes 0 or negative and the high side is down at 100.
What is the difference between the EGX 70HLC and the em3y60hlp? or should I use EMBRACO # FF10HBK/FF10HBK1?(I have a French door, 2 drawer freezer ice and water in the door) thanks
im wondering which one to order also, the ff10hbk seems common for others to use, but it seems to need a hard start capacitor on it. maybe the egx70hlc has a start relay on it?
I try that and don't get it to work you are not getting,12 volt to the fan and next the board will not respond with out the compressor in the circuit thanks let me know what you think God bless keep up the good work
Great video. What kind of a relay did you use? I purchased a 12 Volt Automotive relay and it won’t work. The condenser fan runs on 9 volts and once energized the voltage drops to 4.
Also the board is not able to see the operation of the new compressor. Getting 3 flash codes. Any ideas?
Thank you.
I need more information about this operation excellent
Excelente video pero tengo un problema. El abanico tiene 4 cables y tiene 12vdc constantemente. Cuando se apaga el condenser fan todavía tiene 12v y por esa razón no se apaga el compresor. Tiene algún arreglo para eso? Gracias!
How come you didn't show the other components? Other than what's on the board already?
Does the water dispenser and ice make work norma with this replacement compressor?
My embraco is at 170 f. Is this to hot . Is cooling ok
I do not believe that the use of conventional compressor instead of linear one work as expected, because the linear compressor does not work with ON OFF control temperature, it works with incresasing or decreasing the speed depending of thermal load inside the frige. So when you use a realy taking the PWM signal of feedback signal from Condenser fan just stopping the conventional compressor when defrosting process starts.
Ayudaría mucho un diagrama eléctrico para saber cómo y dónde conectar el relay del compressor y el condensador gracias
ESTA EN EL MINUTO 3:05 USTED DEBE USAR EL DIAGRAMA DEL EQUIPO Q TIENE USTED
did the amount of refrigerant needed change? my swap is only getting into the 40s frdge/20s freezer (f). once it gets this low the lowside goes 0 or negative and the high side is down at 100.
Sounds like it’s either undercharged, leaking, or restricted at the filter drier input
what model embraco compressor ?
you can use any regular compressor, the ones that uses starter relay,PTC. i used an em3y60hlp
@@faleroappliances8111 , how about the upgrade the software to motherboard?
@@chrisnguyenDQ2012 THE UPDATE IS FOR THE LINEAR COMPRESSORS, IS NOT NEEDED IN THIS ONE .
PLEASE LEAVE A REVIEW IF THIS HELPED YOU , THANKS IN ADVANCE.
g.page/r/CaA0PdyfjfuXEA0/review
Where you found that relay board
I just made it myself
USE THIS . www.amazon.com/dp/B00NF0ICSO?ref=ppx_pop_mob_ap_share
LEAVE A REVIEW IF THIS HELPED YOU PLEASE .
g.page/r/CaA0PdyfjfuXEA0/review
What is the difference between the EGX 70HLC and the em3y60hlp? or should I use EMBRACO # FF10HBK/FF10HBK1?(I have a French door, 2 drawer freezer ice and water in the door) thanks
im wondering which one to order also, the ff10hbk seems common for others to use, but it seems to need a hard start capacitor on it. maybe the egx70hlc has a start relay on it?
Hi Falero Appliance, can you draw a diagram to help me more please?
MINUTE 3:05 , CHECK YOUR OWN WIRING DIAGRAM ALL OF THEM ARE DIFFERENT .
I try that and don't get it to work you are not getting,12 volt to the fan and next the board will not respond with out the compressor in the circuit thanks let me know what you think God bless keep up the good work
I have the same issue with the one I’m working on. Did you get it figured out?
Thank you.