How to Replace CV Axle Assembly 2008-2013 Nissan Rogue
ฝัง
- เผยแพร่เมื่อ 27 ส.ค. 2024
- Buy Now!
New CV Axle Assembly from 1AAuto.com 1aau.to/ib/1AAX...
This video shows you how to install a new CV Axle assembly in your 2008-2013 Nissan Rogue. A CV axle has flexible joints. Often, these joints wear out, or seize from contaminants due to the protective boot tearing open. A worn joint is prone to breakage, or other hazards. If your vehicle needs a new CV axle, install a quality TRQ axle that is engineered to your vehicle’s specifications.
This process should be similar on the following vehicles:
2008 Nissan Rogue
2009 Nissan Rogue
2010 Nissan Rogue
2011 Nissan Rogue
2012 Nissan Rogue
2013 Nissan Rogue
Tools you will need:
• Flat Blade Screwdriver 1aau.to/obiA/1A...
• 18mm Wrench
• 13mm Socket 1aau.to/obsB/1A...
• 18mm Socket 1aau.to/oafY/1A...
• 21mm Socket 1aau.to/oafY/1A...
• 32mm Socket 1aau.to/ocx/1AA...
• CV Axle Shaft Popper Tool 1aau.to/of/1AXA...
• Dead Blow Hammer 1aau.to/oTt/1AX...
• Pliers
• Socket Extensions 1aau.to/obsB/1A...
• Torque Wrench 1aau.to/oaDb/1A...
• Cotter Pin
• Gloves 1aau.to/o3I/1AX...
• Safety Glasses 1aau.to/oUS/1AX...
• Bucket
• Chisel 1aau.to/okH/1AX...
• Floor Jack 1aau.to/o4i/1AX...
• Hammer 1aau.to/oTt/1AX...
• Jack Stands 1aau.to/oSI/1AX...
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
Removing tie rod end from knuckle makes life a lot easier when doing this
You don’t need to remove the ball joint just loosen the strut bolts and turn the wheel to the right and let the top bolt slide out leaving the bottom bolt loose but not out all the way and if you have to take the second one out it won’t do any thing to the strut as long as it’s lifted off the ground so no tension is there, and let the strut lean forward so at that angle the axle will slip out easy I’ve changed two of these now I’m on a third one and bearing
I love TRQ videos, and parts.
Instructive and understandble thanks
Great! So clear, thanks!
For the lower ball joint i used various sockets and a prybar against the cv joint to press it thru. A size 14 will fit thru the ball joint clamp.
I had to use a torch on the bearing support bracket to get it out becuase it was really stuck.
The book said to replace the trans seal so i did just to be safe.
Bearing support bracket bolt torque 18 ft lb. Ball joint clamp fastner 46. Axle nut 133-136.
It took me 2 full days. Take your time and make sure when you put the axle into the transmission that the spline is matched because if you start wacking the axle to press the bearing in and it isnt lined up and you mash the spline your transmission will have to be rebuilt
Where can I find a slide hammer with the claw?
Removing the ball joint from the knuckle was difficult. We ended up using a crow bar, placed vertically so the curved bit goes around the knuckle to the bottom of the joint. Then used a sledge on the top of the crowbar to knock it free downward.
Wheel alignment afterwards needed?
How is this video different than the other video?
Thisone needs a new lower control arm ball joint too
Ones passenger side the other is drivers side trq has videos on both
Question
My 2008 Nissan Rogue’s dip stick has the HOT label on it, but it doesn’t have the “greater than & less than” symbol marks. It does contain the hashed area and the two notches. The Hayne’s manual states to fill the fluid between the two notches once the transmission fluid is brought to hot temperature. You’re saying to fill it to the HOT marks. Which is correct? By the way, the operator’s manual doesn’t give any guidance.
Why cut the Cotter pin instead of filing both sides?
How many pounds is the slide hammer?