Nice job on the video , I hv a k24a2 , out of an 05 Tsx , that I want to build a little and put in my 03 crv,5-speed. Information in crv k24 swaps is limited, but your video has plenty of good nuggets , keep up the good work.
Im running K24a2 with K20 oil cooler, water pump and housing, with RSX belt tensioner, power steering pump, k20z1 alternator, on a K20a2 crank pulley and non-ac belt. With dual height Hasport mounts on lowest setting none of it touches the hood.
Im swapping a k24a into an eg. Want to keep AC, can I buy one of these pulley kits (hybrid/k tuned) and keep the waterpump and alternator that came with my motor? I figure if they fail, Ill make the swap down the line, and remove the conversion bracket right? Thanks in advance bro you are a great help and an inspiration
I want to k swap my 2012 honda ge8. I'm looking for a k24a2 with 06-11 SI Trans (SLD). I'm not sure which harness would best setup. You advice will be helpful thanks
I'm very new to kswaping. Honda fits ge8. I'm not sure about the compatibility. But seeing the k24z are the most compatible ones. They typically run i believe tsx harness or accord to my understanding.
My tsx came with k24a4 previous owner sold it to me with blown head gasket i boutght k24a imported i know i am going to need to change water pump housing what about the vetc sensor the k24a doenst have it and anything else that i need to change to make it run
Oh wait one more question, I would usually see people using the accord ecus or Rsx ecus. Could I use those instead or I would have to add those to the ecu
I just bought a fa5 with a k24a rbb3 swap. The alternator is bad, it seems to have the usdm accessories. You had said either a base model rsx alternator or a 02-6 crv alternator should fit correct? Or can I get a k20z3 alternator. New to the k series. Coming from a j series
You would need the crv post mount or you get can an aftermarket universal one. And by pulley I don't know what you mean. You can transfer everything or keep what you wish from the z3.
You tank try I know is been done with the 9th gen si k24a7. The problem is that your engine has sensor not in the same location than the k24a. For example like the crank sensor. On the k24z is located near the flywheel. And on the k24a is by the crank pulley.
Hello bro I have installed the k24A rbb-2 engine on my honda Accord 2004. It worked great i am still using the engine, but i have one problem, and that's the car's The torque is weak
Not sure what bolt ons you have but if you add bigger injectors and bigger throttle body feed it more are it should help gain more. Also look into a standalone like ktuner to solve you problems. Because I'm sure you had the k24a4 and now have a true vtec k24 in there and would need tunning.
On the usdm tsx k24a2 the waterpump housing is fine is only on the jdm k24a. I seen jdm rbb k24a being sold for cheaper than k24a2. But if you could source a k24a2 cheaper with less mileage is good.
Yes you can.. but you will have to change the bracket and the oil pan. Knock sensors. I literally just did it on my wife 2012 last weekend… awd trans.. from the top also.
I believe the euro accord has two versions a type r k20a and a k24a rbb. In the states the accords have a different k24 and usdm tsx/accords only have a k24a2 no type s
I'm not too sure, to be honest. I have heard that the k24z block has different water port vs. the k24a cylinder head. I saw 4piston do it before. Is more common to swap a k20z3 head. I also seen jdm k24z.
No issues, you would have good hood clearance, probably but the oil pan might sit a bit lower. Just swap over from the type s engine the: knock sensor, crank sensor and if you want which I recommend waterpump housing with oil cooler. Intake manifold with everything. And the intake vtc gear along with the whole oil pump kit. And make sure to get your ecu chipped with hondata.
@@Almostboosted does it matter wt year or where from I am new to all of this doing this swap on my ek hatch I wanted run a 5 speed from a rsx but wasn’t sure was possible because the motor is from a tsx
Question to upgrade a 03 Accord K24A4 auto. Any possible upgrades? TSX cylinder head swap, intake manifold, or newer pistons? Love my car and runs great. Just wish it had more power when I do drives up the grapevine.
If you try swapping a different head, you would need to change pistons because it would make contact. Your best bet is swapping the complete engine. And yeah, you could upgrade everything else, but it won't make much power. I'm sure ktuner has flash for the ecu, but it won't be that efficient.
Did you complete your swap? Just did mine on the 04 tsx same ecu and harness. It runs great but eventually would get misfires and knock sensor code. Do you know if I need to tune the tsx to work properly or I there is another underlying problem? In order to tune, I would need to swap the ecu to a newer ecu/immobilizer to get hondata or ktuner to work because the 04-06 ecu is not writable. Leading to more work/money which makes me feel like I should’ve went with a used k24a2 than the k24a3 jdm.
Not sure if you could try ktuner. I would double-check maintenance issues. It's like a tune-up to see if it helps by pulling any DTC codes. If not, you might need to tuned.
To be honest they are very identical the k24a jdm Is the oversea version of the k24a2. Now the 06 to 08 k24a2 is a bit more aggressive vs the 04 to 05 k24a2. I'm sure it could be the same with the jdm k24a. I would just go with the jdm one just because it has way lower miles.
The only difference I see is cosmetic. Like difference overseas water pump housing, alternator and ac compressor, and power steering pump. You typically convert it with a usdm one.
@@Almostboosted oh ok gotcha I wanted to do a K frank (24/20) in my 8th gen si and here where I live this place called jdm place in Houston texas has the k24a for $800 for the long block.
I am throwing mine into a 2001 Honda Insight. Did I hear you correctly that i might not be able to use Hondata with the Japan variation? If anyone has any info on this swap, I am looking for an ECU, Wiring Harness, Hasport Mounts, Accord Parts, I really want to make mine AWD. I am also wanting to do a Naturally Aspirated Build with lighter Crank, Longer Rods, ARP head studs, Higher RPM Pistons, K20 Type R Head, K20 Oil Pump Swap, Warlboro fuel pump are among many on my list for the build.
I have the JDM k24 rbb3 swapped into a 2004 Ep3 and both Kpro and Ktuner works on the setup. I do have a vid when it was on the dyno while tuning on Ktuner.
so what’s better? rbb2 vs rbb3? i have rsx rbb2 on kpro w rbc intake mani and plm headers, custom exhaust. etc. basic bolt ons and my boy has fa5 rbb3 on flash pro w same bolts on but w full race exhaust and i made more power and i beat him. i’m not understanding.
The only thing that changes is the year. The RBB 3 and 4 are newer and have slightly better upgrades. Like the slightly bigger intake valve. But overall, it is not a bid difference to worry about.
There is no need to change the camshaft unless you want better ones. And ecu yes if you are swapping into older honda chassi you need a compatible ecu that has been flash or chipped.
To be honest, yes, the k24a has its advantages. More torque bigger displacement. The k20z3 smaller displacement, les torque but more aggressive cylinder head and flow. I would wait until the k20z3 goes out, or you can interchange parts between them and hace a Frankenstein engine
Awesome good to know! The only problem I’m facing my car has 230k miles and just recently car overheated,blew head gasket, noticed coolant in the oil pan, so sadly it’s time to change out. What is your best advice to make this swap smooth transition?
Get an rbb 2 or 3 jdm k24a. Swap over from the k20z3, the oil cooler, water pump housing with everything. swap over the crank sensor, knock sensor. The intake cam sensor is angle different the vtec pressure switch sensor next to the vtec solenoid by the back of the cylinder head since jdm Engines don't have it. Get a CRV post mount. Flash your ecu with hondata or whatever you can find to tuned. And slap back the transmission. Optional yo can Swap over the k20z3 hear and or rsc type s oil pump kit with a 50° vtc gear
To be honest, I have not personally measured them. But every importer that I seen selling RBB 3. Is way more expensive compared to the RBB 1 and 2. Not sure if it might have the more aggressive cams, but I'm sure it has the slightly bigger intake valve.
Been trying to solve the same riddle myself. Based on my reading even the later RBB3 JDM K24a's stuck with the 04 USDM TSX cams - not the more desirable 06+ K24a2 USDM cams. As a result, in terms of power specs the JDM motors out of the box wont achieve as much peak HP however they do tend to make up for it in torque. Silver lining: this makes a drop in cam even more attractive on the JDM motors especially with 40+ degree VTC
@@Astonmarvinusdm tsx 04-06 is different from usdm tsx 07-08. Both k24a2 Latter has slightly beefier rods. Intake valves are 1mm larger. And cams are better from what I’ve read. However what I’ve also read is that even in the usdm the rbb1,2,3,4 castings don’t always correlate to being an 04-06 vs 07-08. Meaning you can’t rely on it saying rbb3 or rbb4 and assume it’s an 07-08. The consensus has been that it’s not a 100% guaranteed way to tell.
I have seen people use rsx type s waterpump housing. With there k24a even with RBC manifold kinda of a tight fit. For Ac and Ps you would need a k20 or k24 compressor, the rsx type s powersteerimg. Preferably and with a string measure to see what serpentine belt you would need. But I seen hybridracing also have a powersteering kit like lines and hoses. And a Ac kit too to help with kswap.
How many rbb are there in k24a series'? What is type s? Can any one explain me difference in k24a rbb head triptonic type s and k24a rbb head manual transmission
Is rbb head good? What does it mean 1 2 3 4? Also one guy is selling type s rbb head with triptonic, so was concerned would its manual gear give performance like a normal type s manual gear or with lag.
@AhmedJAnsari the best ones to get are 3 and 4 bigger intake valves. And the transmission I doubt they are better than a k20 on just have to look up the gearing ratios.
@@Almostboosted mine says rbb3 does what does that mean ? Is that the good kind 😂 I knew to all this cause I recently purchased a FA5 sedan with a k24a swap and I looked at the crankshaft sensor and it has a rbb3. What car do these come from and how much power does it push
skipped all that stuff and stick with k20z3, k20a2, k24a2.. still put good amount of power also with everything else and probably better than a k24a jdm imo..
I have a K24a JDM motor with RBB-3 head.. I’m searching what is the year of production of the engine.. I read that the serial number also determines the production year.. on the back of the head it’s says 05 which I’m assuming is 2005.. your say will help me further..
@rcgod Not sure if you are referring to a 2.4 or a 3.0 6 cylinder. But your 2007 Accord had this dosplament option 2.4 L K24A4/K24A8 I4 3.0 L J30A4/J30A5 V6. For a jdm 2.4, probably the k24a non rbb. Because it would be the closest to your ecu parameter without reflashing.
I swapped in an 05 Accord water pump housing on my RBB, seem to fit great.
Thank you for sharing this information 🙏 I was always curious but just went with what everyone else posted online while researching.
great to know!
You can use idler pulley and alternator from 2009-2014 K24Z3 TSX on JDM K24A engine, don't need to buy pricey idler pulley.
I try mocking a k24z3 idler pulley on to the jdm waterpump housing, and it did not fit.
Contemplating on swapping a built k into my 02’ S2K. I love my F series though. That 9k rpm is fun
That's what I tell my buddy to do. Because F series are to expensive to replace vs a k series.
03-07 accord water pump housing will fit as well
Nice job on the video , I hv a k24a2 , out of an 05 Tsx , that I want to build a little and put in my 03 crv,5-speed. Information in crv k24 swaps is limited, but your video has plenty of good nuggets , keep up the good work.
Thank you, I appreciate the feedback.
Thanks!
Thank you. I really appreciate the support 🙏
Im running K24a2 with K20 oil cooler, water pump and housing, with RSX belt tensioner, power steering pump, k20z1 alternator, on a K20a2 crank pulley and non-ac belt. With dual height Hasport mounts on lowest setting none of it touches the hood.
What intake manifold you running?
@@Almostboosted 04-05 TSX intake manifold with 03 Accord throttle body.
How much hp did you make with that set up?
The 07-08 ones are the same when JDM. Only different in USDM TSX type-s iirc.
Good information here thank you.
even the JDM water pump got 2 types of outlet, straight facing down and angled
Cast iron piston sleeves I believe on k24a jdm
Im swapping a k24a into an eg. Want to keep AC, can I buy one of these pulley kits (hybrid/k tuned) and keep the waterpump and alternator that came with my motor? I figure if they fail, Ill make the swap down the line, and remove the conversion bracket right? Thanks in advance bro you are a great help and an inspiration
Yes definitely. I would rather invest in a compatible set up all usdm waterpump with matching alternator and accessories it would be a lot easier.
Thank you bro I appreciate it 🙏
@@Almostboosted so you think its worth doing that right now before the car is running?
@ChampinOnEm yeah I would not wait to do it afterwards.
@@Almostboosted thanks bro
I want to k swap my 2012 honda ge8. I'm looking for a k24a2 with 06-11 SI Trans (SLD). I'm not sure which harness would best setup. You advice will be helpful thanks
I'm very new to kswaping. Honda fits ge8. I'm not sure about the compatibility. But seeing the k24z are the most compatible ones. They typically run i believe tsx harness or accord to my understanding.
Can i slap a auto tsx 2006 k24a2 onto my 6speed 2004 tsx?
Yes, but the stock ecu might be off because of the parameters .
My tsx came with k24a4 previous owner sold it to me with blown head gasket i boutght k24a imported i know i am going to need to change water pump housing what about the vetc sensor the k24a doenst have it and anything else that i need to change to make it run
On the back of the head you have the vtec valve. And you need to swap over the vtrc pressure switch, the k24a dosent have it.
I'm doing a k24 awd 88crx, I have 5g in it already but so many options, I just want to keep it simple, by d way what is my budget? Lol😂
Hard to tell lol awd is expensive probably s1. I sure by the time your done probably between 15k or 20k
I own a 5 speed 2005 Honda accord coupe would I need to change anything if I’m doing this swap ???
You're going to have to get your ecu reflash and see what is compatible with the k24a, like plugs and sensors.
I got an accord s type with 6 speed trans and a jdm k24a as soon as o start tearing it down ill be posting vids
I subscribe
u lie
VERY CLEAN BUILD BRO 🔥🔥🔥THANKS FOR THE CONTENT WE WILL BE TUNED IN ON YOUR CHANNEL NOW!!WE ARE SUBSCRIBED ‼️
Thank you so much. I appreciate the support 🙏
NO DOUBT BRO THIS IS WHAT ALL OF US HONDA GUYS SHOULD BE DOIN..SUPPORTING EACH OTHERS BUILD AND NO HATING 🤜🏽🤛🏽💯GOD BLESS🙏🏽
Definitely bro 💯
I subscribe bro
@@Almostboosted appreciate u bro..LETS GOOOO‼️🫡🚀
Which inlet manifold it that on your engine that's already install on the black car please?
Is a RBC Intake Manifold oem from honda.
Hey I’m thinking of getting my a jdm k24a, what ECU should I use? I want to get a 6spd but if I’m ok with settling for 5spd
If you are going with hondata kpro, get the 6 speed 02 to 04 PRB. For the 5 speed, get the PND. If going with ktuner 6 speed 05-06 PRB.
@@Almostboosted oh ok bet thank you!!!
No problem
Oh wait one more question, I would usually see people using the accord ecus or Rsx ecus. Could I use those instead or I would have to add those to the ecu
With hondata kpro, you can not use accord ecus that's only for ktuner.
Do you need to replace the vtech solenoid on the Jdm k24a
No
06 to 08 comew with like 11:1 compression ratio
Negative
Has 36mm intake valve and bigger lobs on the intake camshaft.
R40 k24a has 11:1 not the RBB
I just bought a fa5 with a k24a rbb3 swap. The alternator is bad, it seems to have the usdm accessories. You had said either a base model rsx alternator or a 02-6 crv alternator should fit correct? Or can I get a k20z3 alternator. New to the k series. Coming from a j series
You can get the rsx base alternator, rsx type s, ep3, crv or tsx. Dont get the k20z3 .
@@Almostboosted awesome thanks man. I’ll go to the parts store and compare my current one with the tsx alternator
No problem boss
I a k20z3 engine and looking to just swap over the head to a k24a would i be to transfer everything over?
Yes you can transfer everything
So I wouldn’t need to get the pulley or the crv mount? Or what would I have look out for?
You would need the crv post mount or you get can an aftermarket universal one. And by pulley I don't know what you mean. You can transfer everything or keep what you wish from the z3.
@@Almostboosted I was talking about the hybrid racing idler pulley but that’s only to keep the jdm water pump housing so my mistake
@@Almostboosted but other than the mount everything else should be good? Sorry my first time doing any of this haha
Can i just take out my k24z3 an put a k24a in my 2008 honda accord coupe? Will every thing fit up
You tank try I know is been done with the 9th gen si k24a7. The problem is that your engine has sensor not in the same location than the k24a. For example like the crank sensor. On the k24z is located near the flywheel. And on the k24a is by the crank pulley.
Can***
K24z7***
@Almostboosted so thts the only problem I will have if I change the k24z3 to a k24a? Everything else will work
Double check your wired guide to make sure the pins are correct and get the ecu reflash. But double-check research to make sure.
Hello bro
I have installed the k24A rbb-2 engine on my honda Accord 2004. It worked great i am still using the engine, but i have one problem, and that's the car's The torque is weak
Car torque from 1000 to 2500 rpm ٠
Upgrade the clutch and flywheel to a stage 2 atleast.
Not sure what bolt ons you have but if you add bigger injectors and bigger throttle body feed it more are it should help gain more. Also look into a standalone like ktuner to solve you problems. Because I'm sure you had the k24a4 and now have a true vtec k24 in there and would need tunning.
Air***
Should I just get the USDM k24a2? I heard the waterpump has to be configured and im looking to keep P/S
On the usdm tsx k24a2 the waterpump housing is fine is only on the jdm k24a. I seen jdm rbb k24a being sold for cheaper than k24a2. But if you could source a k24a2 cheaper with less mileage is good.
Thank you! Super dope content
Thank you, Erick. I appreciate it 🙏
Can you swap a K24a RBB3 into to stock 2014 CRV?
Yes but it would require more stuff to be replaced. Your better off going with a jdm k24z r40 direct fit.
@@Almostboosted Thanks bro!
2013 crv USA car has k24 engine blew. Can I put a jam variant to fit with no probs its auto
Yes you can, just get a k24z varirent with the r40 head. You might have to swap over sensor and what not but is possible
I have a 2013 civic si and it has a k24z7 if it was to go out I would definitely go with a jdm k24z or a k24a.
Yes you can.. but you will have to change the bracket and the oil pan. Knock sensors. I literally just did it on my wife 2012 last weekend… awd trans.. from the top also.
What’s the difference between rbb2 rbb3 and rbb4
Year it was made rbb3 rbb4 are 06 to 08
Is the accord a type s motor
I believe the euro accord has two versions a type r k20a and a k24a rbb. In the states the accords have a different k24 and usdm tsx/accords only have a k24a2 no type s
Hey bro is it possible to slap a k24a rbb 3 lobe vtec. On a 9gem civic si sedan my motor is done.. I haven’t really seen them do that..
I'm not too sure, to be honest. I have heard that the k24z block has different water port vs. the k24a cylinder head. I saw 4piston do it before. Is more common to swap a k20z3 head. I also seen jdm k24z.
What needed to swap this into an rsx type s and will i have clearance issues?
No issues, you would have good hood clearance, probably but the oil pan might sit a bit lower. Just swap over from the type s engine the: knock sensor, crank sensor and if you want which I recommend waterpump housing with oil cooler. Intake manifold with everything. And the intake vtc gear along with the whole oil pump kit. And make sure to get your ecu chipped with hondata.
Can I run a 5 speed from a rsx or do I have to run a tsx 6 speed bc my k24a is from a tsx
You can definitely run a 5 speed
@@Almostboosted does it matter wt year or where from I am new to all of this doing this swap on my ek hatch I wanted run a 5 speed from a rsx but wasn’t sure was possible because the motor is from a tsx
@@Almostboosted appreciate the response
Yeah it dosent. Matter. My friend swapped a k24 in his rsx with a accord 5 speed.
No problem
Question to upgrade a 03 Accord K24A4 auto.
Any possible upgrades? TSX cylinder head swap, intake manifold, or newer pistons?
Love my car and runs great. Just wish it had more power when I do drives up the grapevine.
If you try swapping a different head, you would need to change pistons because it would make contact. Your best bet is swapping the complete engine. And yeah, you could upgrade everything else, but it won't make much power. I'm sure ktuner has flash for the ecu, but it won't be that efficient.
will my 04 tsx ecu and harness work with the rbb?
If kswapiing on an older honda chassi, I'm not sure if with ktuner it could, but not kpro. If swapping the RBB to your 04 TSX yes.
Did you complete your swap?
Just did mine on the 04 tsx same ecu and harness. It runs great but eventually would get misfires and knock sensor code.
Do you know if I need to tune the tsx to work properly or I there is another underlying problem?
In order to tune, I would need to swap the ecu to a newer ecu/immobilizer to get hondata or ktuner to work because the 04-06 ecu is not writable. Leading to more work/money which makes me feel like I should’ve went with a used k24a2 than the k24a3 jdm.
Not sure if you could try ktuner. I would double-check maintenance issues. It's like a tune-up to see if it helps by pulling any DTC codes. If not, you might need to tuned.
Any difference between the k24a and the k24a2?
To be honest they are very identical the k24a jdm Is the oversea version of the k24a2. Now the 06 to 08 k24a2 is a bit more aggressive vs the 04 to 05 k24a2. I'm sure it could be the same with the jdm k24a. I would just go with the jdm one just because it has way lower miles.
The only difference I see is cosmetic. Like difference overseas water pump housing, alternator and ac compressor, and power steering pump. You typically convert it with a usdm one.
@@Almostboosted oh ok gotcha I wanted to do a K frank (24/20) in my 8th gen si and here where I live this place called jdm place in Houston texas has the k24a for $800 for the long block.
@NightHawk_FA5 make sure it is an RBB head that's real true vtec.
@@Almostboosted RBB 2 head and 3 lobe vtec cams from what the guy said.
New sub! Getting more key info in case l get a K fever again!
Thank you for the support. I hope I'm able to help.
I am throwing mine into a 2001 Honda Insight. Did I hear you correctly that i might not be able to use Hondata with the Japan variation? If anyone has any info on this swap, I am looking for an ECU, Wiring Harness, Hasport Mounts, Accord Parts, I really want to make mine AWD. I am also wanting to do a Naturally Aspirated Build with lighter Crank, Longer Rods, ARP head studs, Higher RPM Pistons, K20 Type R Head, K20 Oil Pump Swap, Warlboro fuel pump are among many on my list for the build.
Im sure you should be able. I know of a guy on my ig that did it but not sure if he would share info. He said it was a lot of research.
I have the JDM k24 rbb3 swapped into a 2004 Ep3 and both Kpro and Ktuner works on the setup. I do have a vid when it was on the dyno while tuning on Ktuner.
I have a k24a jdm engine in my 97 dx hatch. I use hondata kpro v4
What do you think about the k24a1 am thinking bout doing that in DC Integra I want it to be road trip Worthy
To be honest, I like k24a1 it has potential. But the k24a1 is not a true vtec k24, but for a budget, no power build is perfect.
so what’s better? rbb2 vs rbb3? i have rsx rbb2 on kpro w rbc intake mani and plm headers, custom exhaust. etc. basic bolt ons and my boy has fa5 rbb3 on flash pro w same bolts on but w full race exhaust and i made more power and i beat him. i’m not understanding.
both are k24a
The only thing that changes is the year. The RBB 3 and 4 are newer and have slightly better upgrades. Like the slightly bigger intake valve. But overall, it is not a bid difference to worry about.
USDM RBB3 can be the 1mm bigger valves if from the TSX-S, same as the rest if its JDM.
Awesome I have a 2006 rbb 3
I asked from some people and they told me that i have to change engine camshaft or the ecu ???
There is no need to change the camshaft unless you want better ones. And ecu yes if you are swapping into older honda chassi you need a compatible ecu that has been flash or chipped.
Isn't the connector for the JDM alternator different from the USDM one as well?
No is the same obd2 green plug I've seen it also in black.
@@AlmostboostedI think he means the mount not the plug
I see.. 🤔 yeah, the jdm alternator has a different mount, but I seen. Some with the same usdm mounts.
Is The K24a JDM RBB better than my current k20z3 on my 8th Gen Si?
To be honest, yes, the k24a has its advantages. More torque bigger displacement. The k20z3 smaller displacement, les torque but more aggressive cylinder head and flow. I would wait until the k20z3 goes out, or you can interchange parts between them and hace a Frankenstein engine
Awesome good to know! The only problem I’m facing my car has 230k miles and just recently car overheated,blew head gasket, noticed coolant in the oil pan, so sadly it’s time to change out. What is your best advice to make this swap smooth transition?
Get an rbb 2 or 3 jdm k24a. Swap over from the k20z3, the oil cooler, water pump housing with everything. swap over the crank sensor, knock sensor. The intake cam sensor is angle different the vtec pressure switch sensor next to the vtec solenoid by the back of the cylinder head since jdm Engines don't have it. Get a CRV post mount. Flash your ecu with hondata or whatever you can find to tuned. And slap back the transmission. Optional yo can Swap over the k20z3 hear and or rsc type s oil pump kit with a 50° vtc gear
Head***
Awesome! Thanks for the helpful advice! I’m making parts list now and taking my time to gather everything I need before I get this projects started.
Been trying to confirm whether the USDM K24a2 has more aggressive cams than an RBB3 K24a. I believe that's what you're saying here. Confirm?
To be honest, I have not personally measured them. But every importer that I seen selling RBB 3. Is way more expensive compared to the RBB 1 and 2. Not sure if it might have the more aggressive cams, but I'm sure it has the slightly bigger intake valve.
Been trying to solve the same riddle myself. Based on my reading even the later RBB3 JDM K24a's stuck with the 04 USDM TSX cams - not the more desirable 06+ K24a2 USDM cams. As a result, in terms of power specs the JDM motors out of the box wont achieve as much peak HP however they do tend to make up for it in torque. Silver lining: this makes a drop in cam even more attractive on the JDM motors especially with 40+ degree VTC
I like how the jdm k24a has a bit more torque.
Correct
@@Astonmarvinusdm tsx 04-06 is different from usdm tsx 07-08. Both k24a2
Latter has slightly beefier rods. Intake valves are 1mm larger. And cams are better from what I’ve read.
However what I’ve also read is that even in the usdm the rbb1,2,3,4 castings don’t always correlate to being an 04-06 vs 07-08. Meaning you can’t rely on it saying rbb3 or rbb4 and assume it’s an 07-08.
The consensus has been that it’s not a 100% guaranteed way to tell.
I would like to know if the half shaft from the k24a2 ( TSX USDM) works with the axles from RSX base model . Thank you
I belive the tsx and accord half shafts are to long, manual rsx, ep3 and the si should work. I bought 06 to 11 civic si ones.
44500-SCV-A00 all the compatible intermediate shaft share this part number
@@Almostboosted I ask you, does it not matter if in the case of a half shaft of an element it is automatic or manual?
@vocs03 from what I heard, yes, you can use auto. In fact, I saw a crv auto with the rsx style intermediate shaft at the yard.
@@raysb240sx so the half shaft from the k20z3 fits in the block of the k24a2?
Can a 02 rsx type s water pump housing fit the jdm motor? What else would I need to use for ac and ps ?
I have seen people use rsx type s waterpump housing. With there k24a even with RBC manifold kinda of a tight fit. For Ac and Ps you would need a k20 or k24 compressor, the rsx type s powersteerimg. Preferably and with a string measure to see what serpentine belt you would need. But I seen hybridracing also have a powersteering kit like lines and hoses. And a Ac kit too to help with kswap.
Appreciate the Jems 🤝
@@rvmangvd4050 any time
Do u have to do anything to your engine to keep it from rusting if you're not planning to do anything to it but stored it for 1 year?
If you want, you can spray a bit of wd40 on all the steal parts and cover it.
How many rbb are there in k24a series'? What is type s? Can any one explain me difference in k24a rbb head triptonic type s and k24a rbb head manual transmission
From my knowledge, there are RBB 1, 2, 3, and 4. Here in the States, we only got k24a2, but Is k24a equivalent .
Is rbb head good? What does it mean 1 2 3 4? Also one guy is selling type s rbb head with triptonic, so was concerned would its manual gear give performance like a normal type s manual gear or with lag.
@AhmedJAnsari the best ones to get are 3 and 4 bigger intake valves. And the transmission I doubt they are better than a k20 on just have to look up the gearing ratios.
How can you tell if its a k24a 3 lobe?
In the side off the head by whete the camshaft sensors are located just about the side water neck. It should say RBB- either 1,2,3 or 4
Thank you
@@Almostboosted mine says rbb3 does what does that mean ? Is that the good kind 😂 I knew to all this cause I recently purchased a FA5 sedan with a k24a swap and I looked at the crankshaft sensor and it has a rbb3. What car do these come from and how much power does it push
Yeah, it is a good k24. I have an RBB-3 in my eg hatchback. Is a 2006 it has 36mm intake valve. I made 240hp and 195ft lb.
@@Almostboosted I'ma do a oil change tomorrow. What oil should I use ?
👍💪🤝🔥💯
skipped all that stuff and stick with k20z3, k20a2, k24a2.. still put good amount of power also with everything else and probably better than a k24a jdm imo..
Thanks for your honest feedback. But the jdm k24a is still cheaper and comes with fewer miles and has more torque for the money.
Sure buddy, find me a 45k mile USDM k24a2 for $999.00 delivered. Go on and try. I'll wait.
Spot on 👌
I have a K24a JDM motor with RBB-3 head.. I’m searching what is the year of production of the engine.. I read that the serial number also determines the production year.. on the back of the head it’s says 05 which I’m assuming is 2005.. your say will help me further..
@shahnawazkhan9180 not sure on the jdm k24a. But the k24a2 the rbb3 starts un 06.
What’s the best JDM engine swap ivtec for a 07 accord auto?
@rcgod Not sure if you are referring to a 2.4 or a 3.0 6 cylinder. But your 2007 Accord had this dosplament option 2.4 L K24A4/K24A8 I4
3.0 L J30A4/J30A5 V6. For a jdm 2.4, probably the k24a non rbb. Because it would be the closest to your ecu parameter without reflashing.