How to connect the mitsubishi Electric MAC-567IF-E or MAC-587IF-E in less then 10 minutes
ฝัง
- เผยแพร่เมื่อ 5 ก.ค. 2024
- 0003 192.168.11.1/network
update no.1 from July 27 2023
Please Note!!!
When you reach 2.56 minutes !!!
if you have enter 192.168.11.1 and you can't see the “wireless configuration screen”, please
write
192.168.11.1/network
Hi guys and welcome back
So today I'm going to teach you how to connect the Mitsubishi Electric Wi-Fi interface
Model MAC-567IF-E or MAC-587IF-E which I'm holding here in my hands in the quickest way I know of.
In 3 simple steps.
Before you start this proses, make sure you have read the safety instruction that provide with it. These instructions are appointed to authorized technicians.
So actually who is this Video for? If you are experience air conditioning installer, and you already installed few of those MAC-567IF-E or MAC-587IF-E - you can skip to the end to see the gift I prepared for you.
you can down load the file here:
MAC-567,587IF-E list of connectable indoor units
drive.google.com/file/d/1gV4l...
If you are an air condition installer and it is your first time-or you have many years of experience but you are uncomfortable with hi-tech things/stuff, then this movie is appointed for you.
So, with that being said, let's get right into it.
The connecting can be done by 3 basic simple steps that you need to go through.
Pay attention-In case you need to connect more than one interface in the same project, I recommend you for each interface to go through step number 2 before starting the next one.
Step No. 1
First-you must turn off the breaker of the indoor unit, then you have to connect this RED connector of the MAC-567IF-E or MAC-587IF-E to indoor unit PCB CN105 connector. (if you don’t know where the CN105 is, please leave me a massage at the comments section).
Please pay attention
A-the interface CN105 connectors were added gradually to the indoor units since 2007, so there is a probability -especially for older system-that some of the indoor units will not equipped with it.
And
B-don’t worry, we have prepared for you a PDF file with some of the old units that has this connector.
You can download it from the subscription.
Step No. 2
In this step we'll connect our wi-fi interface MAC-567IF-E or MAC-587IF-E to our home router without using the WPS button.
Please take a pen in your hands and press on the MODE button (i.e. fill a little click when you are pressing the button) seven seconds continuously wait approximately 60 seconds and you will see that the UNIT and the MODE LED's are flashing every five seconds.
Then take your smartphone in your hands and go into your wi-fi connections screen on your smartphone
And look for the network that started with the letters ME-#####, get into it and you will ask to put a Password, the Password is written under the KEY: ######.
Maybe you will get a question "are you sure you want to get into this network?" please click "Yes"
Then take a scanning App and scan this barcode on the back side of the wi-fi interface MAC-567IF-E or MAC-587IF-E in order to get to you wi-fi configuration screen, if it doesn’t happen you have another way: just open your web browser and type 192.168.11.1 and you will get to the same Wi-Fi configuration screen.
In this wi-fi configuration screen you type: you SSID which is you home network name and you PASSWORD
Roll down to the end of the screen and press the SUBMIT button.
You have to be a little patient and wait approximately one minute then you will see that the
UNIT & NET Led's are flashing every five seconds. If it doesn’t happen-maybe you did something wrong, you have to start Step No. 2 all over again.
You take a pen in your hands and press the RESET button 14 seconds contenuaslly in order to see that the Green UNIT LED is flashing again, then start Step No. 2 all over again.
Step No. 3
You have to download the MELcloud App and follows its instructions.
Help us make things better
Best regards
Itay Ran
Very good : precise, concise, efficient
We wish all the tutorials on yutube were this good!,
Thank you very much
very cool, thank you very much and cheers from Germany :-)
Good guide, very helpful. Thanks.
What an excellent guide. Well done!😃
Thank you very much for the response, I really appreciate it
Thank you so much for your guide : clear and effective ! The only issue : email adresse doesn't work. Need to connect with wps on your wifi router.
Hi, Sorry for my misunderstanding of your question. what do you mean "email adresse doesn't work"? do you mean that you can't connect to the wireless configuration screen by type 192.168.11.1(min 2:59)? or something else
by type 192.168.11.1 ?
Thnx!
Great and helpfull information!
great
the replay below is for a question from: James Crowe
HI, thank you for this! We have the PLA-SM.EA indoor unit and the MAC-567IF-E WiFi module. Unfortunately I don't see a CN105. We do have a CN41 connector that would physically fit and is labelled 'HA TERMINAL-A'. Might this be compatible? Thanks!
Great video I have a EHSC-VM2D. Where is CN105 located?
the CN105 connector(Red color) located On the right side in the middle of the height of the P.c. Board. see the attached picture drive.google.com/file/d/1XIdzOT_G4T7urQlVLfJ7RniK6yrpshTq/view?usp=sharing
great video
Hello, thank you for this video. My machine does not have the CN105 port. I have a FDURA501 as indoor machine and don’t see this port… can you please help me?
hi, the CN105 connector is at Mitsubishi Electric indoor unit. your model is Mitsubishi heavy indoor unit(It's a different company with different air conditioners)
Hello I have MITSUBISHI ELECTRIC MAC-567IF-E Wi-Fi Card with a connector with only 4 wire and need to connect it on a 5 wire cnn
I would need MITSUBISHI ELECTRIC MAC-587IF-E Wi-Fi but some people told me we can only buy the small red stuff connector with 5 wire and only put 4 wire in it but I do not know where to buy it and what is exactly the reference or name of this stuff.
Any idea please?
hi, i am encountering this 4 wire issue for the first time from you question. can you please:
A. send we a picture of your 4 wire mac-567if-e (as meny pictures as you can)? Did it come like this in the original box?
B. tell me what is exactly the model name of the indoor unit(that you want to connect it to the MAC-567if-E).
C.Your country of origin.
D. the MAC-567 and 587 are almost identical(they have minor dimensions changs and a different country of manufacture, however their functionality are the same)
Hi, what is main difference between MAC-567IF-E or MAC-587IF-E, and wich of them can I buy for my Mitsubishi MLZ-KP35vf
The differences between them are minor. The MAC-587IF-E is a newer model But their function is the same. The height and width of the 587 are smaller by a few millimeters, their visibility is a little different And their country of manufacture is different . both of them will fit to the MLZ-KP35VF, The 567 may no longer be available because its production may have been discontinued
great, thanks. Everything took me 1hr without reading any instructions, I used this and the other video on how to open and find the connector (th-cam.com/video/rmY9pEyQ29Q/w-d-xo.htmlsi=omzFI0fggA3fzRrd) - msz-ap type
I'm glad to hear that the video helped you.
I wish you a day full of interesting installations 👍.
Great info. I am searching for the CN105 on my SEZ-KD50VAQ, but I am not able to find it in the manuals (probably because it is an older model). After connecting the wireless interface, the wired controller (PAR-21MAA) will also be active - did I get it right?
please see the attached picture with the SEZ-KD50VAQ CN105 red connector. the PAR-21MAA will be active also drive.google.com/file/d/1C_B670NYw3m2oWXtwglhlmAzyB-V4-9T/view?usp=sharing
@@todayhvac I have managed to order the interface and even to connect it to the system - it works without any issues! The number of the connector (cn105) was written on the plate as well.
Thank you for your assistance!!
I'm glad you made it, have a good day
Hi, I have a mfz-kt35vg. I can only find the cn104 connector, but I don't see the cn105. Can you help me?
hi, the CN105 connector is very close to the CN104. i think that it is in RED. you can use glasses becuse the writing is very small, please see the attached file drive.google.com/file/d/1QhgNtgK5NY2c6YXFzWgTQfF2G7R2lCFL/view?usp=share_link
is there a module to allow you to connect the aircond unit to internet by ethernet cable ? (not wireless but wired)
System controller AE-200 has ethernet connection
amazing video. I did encounter an issue. i have over 40 interfaces mac-567. now ive installed a new machine with the 587 and these cant connec to the melcloud server. its strange that its only the 587 and 577. did anyone had this issue as well? Kind Regards
if you can't get to the "wireless configuration screen" -> In my opinion, the software may have been updated or upgraded over the network , so it is necessary to type in the browser 192.168.11.1/network If you have seen another phenomenon, feel free to share it and we will try to help
192.168.11.1/network
@@todayhvac Thank you for the reply. It connects to my wifi and its respoding. The error states that it cant connec to the melcloud Server. Its strange because its only these MAC models that does this .
Honestly, we haven't heard about it recently. We sometimes encounter a software update after installation (we once encountered that the error light flashed and it was resolved after a few days)
There might be something with the servers, try contacting the distributor.
Good video. But I have difficulties with connection. I think that module don't want to connect to my router
1. do you know the name of your indoor unit?
2. what is the name of the wi-fi interface?
@@itayran981 indoor unit is Lossnay.
Wifi is 587.
Someone said that i need to update firmware of ERV
hi Andrey. you can send me an email with the picture of your Lossnay model and i will ask the manufacturer if it can be connected via the MAC-587IF-E.
i.e. it can take few days to reacive an answer form them.
@@todayhvac ok. I'll make photos tomorrow
@@todayhvac it will be great, because our local Ukrainian suppliers of ME don't have answers)))
Hello .
Please some help.
I conect the phone to the mitsubishi wifi, after that i canot conect to the 198.11... because i dont have net, the phone is on mitsubishi wifi.
Should i disconect the mitsubishi wifi and then conect to 198.11...?
Hi, i hope i understand you correctly-please try to type 192.168.11.1/network. (today you can't get access to the wi-fi configuration screen if you type 198.11....., please open the movie Description )
Announcement 17/04 : drive.google.com/file/d/1XSiHeP3wfpBQgyHzS01UwiQYECIicfBA/view?usp=sharing
The connectors on the 567 and 587 units are different I think : the 567 has a bigger connector, while the 587 has a smaller one. My CN105 port is quite large (about 1 cm long), so I don;t think the small 587 unit will plug in there ?
The connector that connecet to the CN105
is exactly the same for both MAC-567 a MAC-587
@@todayhvac I doubt that : on the 577 the connector is much smaller than on the 567. I have 2 units : one has a 567, other has 577. The devices look the same, but connectors are different.
the connectors of the 567 & 587 are exactly the same. unfortunatly i don't know the 577, however-if it is connect to the CN105 then it must feet. you can send me the pictures to itay.ran@econ-tec.com if you want me to look at it.
Hello
Im am able to Connect to the a/c-wifinetwork
But i can not continue to the “wireless configuration screen”
Why..?
Im am using a iphone 😊
I hope you can help👍
/T
Dear t svent Sorry for the late response. I understand your situation, really.
Unfortunately, I don't have a good answer to give you except that:
1. The action you performed is correct, you did nothing wrong. I don't know what caused this problem
3. Please contact your supplier, he should give you answers and a solution
4. If I know of a solution, I will update you
By the way if I may ask, what is your country of origin?
in order to see the "wireless configuration screen" please type in your browzer: " 192.168.11.1/network" (i.e. with an emphasis on network")
Write in the browser "192.168.11.1/network"
192.168.11.1/network
Thanks 👍☺️
But I do not get the “wireless configuration screen”😢
I am from Scandinavia👍
My wifi unit suddenly lost connection yesterday after trouble free operation for over 2 years. No matter how many methods I try it just will not reconnect to my wifi. Is it possible for it to simply break and require replacement?
can you see what are the LEDs pattern? page 7 at the attached link drive.google.com/file/d/1l4vYDzHRTr-jXocEs4Oih4Iym6ASvGAZ/view?usp=sharing
@@todayhvac I can't remember now. So many different patterns but always involving the Orange (ERR) LED. Been trying all day and frankly so tired and frustrated now that I've given up.
if the NET the UNIT and the ERR are blinking mean that: Connection to MELCloud failed, and
Connection to indoor unit established. Since you tell me you've tried everything and nothing works-Try talking to your installer who will contact the company
You did everything right, it's not a problem for you, there is probably a problem with Melcloud's servers
@@itayran981 thank you. All fixed now.👍