Hello and thanks for the great video. Question, I used your link to possibly buy this drone on Banggood since they have the lowest price. The site states: GEPRC MOZ7 HD 320mm F7 6S 7 Inch Long Range RC FPV Racing Drone PNP BNF with 50A BL_32 ESC DJI O3 Air Unit Digital System - ELRS 2.4GHz . It states PNP in the description but also it comes with the ELRS 2.4GHz receiver! I have the DJI Goggles Integra and also the DJI Remote Controller 2. If I buy this drone will it bind with my goggles and controller? Its a bit confusing as I dont want to have to buy a differnt radio transmitter in case it wont bind. Thanks for any advice
please make a video on geprc maten VTX that boats with 2.5w power. And how to setup and wch cameras are supported and wch goggles can be used to hookup with it.
Hey JB, Great video as always! I'm looking forward to your livestreams starting up again soon! I had a 7" drone a few years ago that ran on 2s lipos! It was awesome too, I must've gotten over a 150 packs on it. I no idea how weird it was until much later lol!
I’m going to use the rekon 7 pro frame With Runcam link wasp Elrs rx 55a stack Am 2807 1500kv motors will this be a solid build to speed cruise mt surf a diving a some mild freestyle.
Just got my MOZ7 in yesterday. I can not wait to get my FPV goggles next. Currently flying line of sight and the tune out of the box is so smooth. My only question is, will it hurt the DJI 03 air unit if I am not using the goggles?
Hi, I'm building a GEPRC MOZ 7 HD. What stack unit do I purchase for this build? And is the flight controller and MCU considered the stack?? I have a dji fpv controller
Iv been watching you for years and I love the videos you bring us thank you. I do have a video request that I feel could be one of the biggest step forwards in the fpv comunity. I would love to see a mod that would alow us to install a walksnail hdzero or even dji digital system into the quest 3 . 120hz 4k resolution full wifi 6 to use bf in field. The quest 3 would be my dream come true as fpv. Og mented reality fpv system would also eliminate the need of a spotter
I don't recommend the analog one unless you plan to swap out the vtx. My mmcx connector was only glued/fell out the second I touched it. Glad I didn't just bind/fly and only noticed because my analog feed wasn't super clean.
Is anyone else having trouble binding the TX16S with Crossfire to the to the quad?? The goggles to the 03 air unit went smooth but I'm having no luck with my controller to the receiver. If you could make a quick short video of you doing that part real quick I would be beyond gratefull. I have the TBS version.
what about the power and battery tabs? i'm upgrade the firmware to 4.4.2 ... and now the battery still beeping just in 24.9v to 20v as low battery... i fly with 1500mah 6S 4.35v per cell.... somebody knows the amperage volts scale of the ESC? this is a SPAN F722-BT-HD V2 Stack thankssss!!!
JB, I don’t always pay attention though I don’t remember if/when you mentioned when you’re back doing Q&A. When can the Beautiful Sausages expect a resumption of normal service? 🤔 (Happy Halloween 👻🎃)
does anybody have the betaflight 4.5 version CLI/setup, with PIDs and everything? because apparently betaflight 4.4 has issues with GPS (what moz7 ships with). I tried running my backup 4.4 on 4.5 and it only set some of the things, did not set PIDs (and who knows what else...)
I’d rather put angle mode on a switch instead of horizon mode. To me, horizon mode is like what you’ll find on toy drone, where it stabilizes itself but then does flips and rolls automagically with the push of a button
Hello, I know you have heard it before a thousand times from everyone else but one more time won’t hurt. THANK YOU for teaching us something new everyday. I wathced this video and I have a quick question for you, the presets you showed specially the cinematic one. Can that be applied on any drone like mark 5 for example or is it only good for the Moz7?
@@JoshuaBardwell so i know im a little too late to the party and this video is not so new, so in the video you reference the "based on the 533 racing rates for cinematic" which is what i like to fly. however i don't see that one listed anymore. do you have one equivalent tothat one that is good for cinematic and also since now we are on 4.5 and a lot of the say. 4.3, 4.4 but I'm on 4.5, what is the deal with the backward comparability? sorry man, total noob over there (3 weeks old to be exact lol)
Hey Joashua, i copied your setup from pastebin and pasted it into Betafligh 4.3.2 CLI. Now I have no more information in my DJI Goggles 2. can I delete the setup again ?
JB’s HD OSD is meant for BF 4.4. You either have to upgrade you firmware, which I recommend only if you know what you are doing, or revert your configuration. Hopefully, you backed it up
@@MrAlucardDante Thank you very much for your help. I was able to solve it with the following code :) set osd_displayport_device = MSP set displayport_msp_serial = 0
Awesome video, I'm actually on the market for a long range beside the Chimera and the Moz I'm also looking at the Rekon7 acn you please maybe do a review on that one, also I was gonna purchase a Elrs module or crossfire for my X9D+ but coincidently it literally caught on fire yesterday, so now I gonna purchase the Boxer Max but want to know aboult Elrs long range capability since is 1w how does it fair, can you test it out of the box, what u think? Thank!!!!
That's crazy your radio caught of fire! ELRS at 1w and a packet rate under say 500 should outrun your video unless you've done a lot of customizing on your video range. It's way more than most people need but if you do need more range it's very versatile so you could do some stuff to squeeze even more out of it. Hope that helps!
@jonah6496 thanks for the info it helps to know, yeah it was scary moment the flame went up and it reached the roof the super good thing is I get to buy the Boxer Maz😁
I released a review when it first came out, but then Chris Rosser discovered the initial review units were defective and not outputting the correct output power. As a result, I took down the review, because I don't want to spread inaccurate information. When I have a unit that I am confident is not defective, I will review it.
I thought you were out for a bit? or is that just the livestream? OMG Bardwell what have you done to me? I just built another 5" and I have 2 7" inch frames ordered.
Congrats on the 300k subscribers, Joshua! 😃 But yeah, I noticed how excited you get when you say that you're going to use the Betaflight configurator! 😂 Anyway, stay safe there with your! 🖖😊
I wish they would stop using LHCP antennas on BNF's designed around the DJI O3, but I do love the Moz7 - the GoPro mount with the carbon plate is a great innovation and the side plates make the drone feel super finished - it's perfect for the long-range and medium-range cruising flights I like to do to get scenery shots here in the Andes.
Because you will get less range than you would by using a dual polarized antenna designed specifically for the O3 system. LHCP on the quad will work, it just won't take full advantage of the potential of the O3 system. For those using Goggles V1 or Goggles V2 it doesn't matter, and for those with G2, you have the option of using LHCP antennas via the Lumenier adapter, but those with the Goggles Integra are stuck with the built-in antennas which re not LHCP. Like I said, it will work fine, just not at the system's maximum potential.@@RandoManFPV
@@colibrifpv a gotchya. So it's not that lhcp is bad; it's jus that those BNF builds always use lhcp but the goggles don't use lhcp. And due to the lack of continuity you lose range yea? Like the bnf being lhcp wouldn't matter if the goggles were also using lhcp right?
Yeah exactly, ideally you want to match polarization on both ends, goggles and quad. I am using Goggles Integra with these LHCP antennas from GEPRC on my Moz7 build and the range seems pretty good, but knowing I could get somewhat better range and penetration bugs me a little. I will try the long Flyfish antenna made for O3 and see if it makes any difference... @@RandoManFPV
Has been thoroughly tested in Ukraine, seems to perfom well with payloads.
NAHHH 💀
Are these the brand of drones Ukraine is using?!?
I have learned and will now use the widescreen setting for OSD in the upcoming HD.
That moment you know you’re overworked, and could use a second or even 3rd pair of eyes, to check you didn’t make a typo in the video title… “seutp” 😊
LOL I was waiting for him to fly it 😅
I ordered a Moz 7 frame last night! Planning for it to be my first HD build, and long range, high speed cruiser. I’m stoked! Will be running Inav.
Dude u read 📚 my mind. This beast was about to be ordered. Awesome review 👏
Congrats on 300k🎉
Hello and thanks for the great video. Question, I used your link to possibly buy this drone on Banggood since they have the lowest price. The site states: GEPRC MOZ7 HD 320mm F7 6S 7 Inch Long Range RC FPV Racing Drone PNP BNF with 50A BL_32 ESC DJI O3 Air Unit Digital System - ELRS 2.4GHz
. It states PNP in the description but also it comes with the ELRS 2.4GHz receiver! I have the DJI Goggles Integra and also the DJI Remote Controller 2. If I buy this drone will it bind with my goggles and controller? Its a bit confusing as I dont want to have to buy a differnt radio transmitter in case it wont bind. Thanks for any advice
Legend is back! 🥳
please make a video on geprc maten VTX that boats with 2.5w power. And how to setup and wch cameras are supported and wch goggles can be used to hookup with it.
Hey JB, Great video as always! I'm looking forward to your livestreams starting up again soon!
I had a 7" drone a few years ago that ran on 2s lipos! It was awesome too, I must've gotten over a 150 packs on it. I no idea how weird it was until much later lol!
I’m going to use the rekon 7 pro frame
With Runcam link wasp
Elrs rx
55a stack
Am 2807 1500kv motors will this be a solid build to speed cruise mt surf a diving a some mild freestyle.
Just got my MOZ7 in yesterday. I can not wait to get my FPV goggles next. Currently flying line of sight and the tune out of the box is so smooth. My only question is, will it hurt the DJI 03 air unit if I am not using the goggles?
That elrs antenna, i see it located in the front, its good than put in the back? My elrs 2.4, probably interference my gps😂
Where is the receiver with the cross antenna things that are in the front of some drones??
commissions incoming 💚😊 thank you very much Josh.
Hey Josh any way we could get a video on how to set up a vtx and a reciver on a aio flight controller specifically the fc that comes with the mobula8
Hey Joshua I have a question about a 7in quad I’m building.
hey great videos, I just bought a moz7 all your fault lol, but you only have one set of rates I can't find the racing rates did you take them off ?
Hi, I'm building a GEPRC MOZ 7 HD. What stack unit do I purchase for this build? And is the flight controller and MCU considered the stack?? I have a dji fpv controller
Iv been watching you for years and I love the videos you bring us thank you. I do have a video request that I feel could be one of the biggest step forwards in the fpv comunity. I would love to see a mod that would alow us to install a walksnail hdzero or even dji digital system into the quest 3 . 120hz 4k resolution full wifi 6 to use bf in field. The quest 3 would be my dream come true as fpv. Og mented reality fpv system would also eliminate the need of a spotter
Ryan Quellet did show how to use the Quest 2 with HDZero, but the latency is trash
You don't receive new walksnail x goggle for review?
I am on a trip and will make content when I get back.
They should have rescheduled the product launch.
@@JoshuaBardwelldo review betafpv pavo 20 & geprc darkstar 20 pls.
Can we expect any good Black Friday deals this year? From getfpv or geprc possibly?
I don't recommend the analog one unless you plan to swap out the vtx. My mmcx connector was only glued/fell out the second I touched it. Glad I didn't just bind/fly and only noticed because my analog feed wasn't super clean.
Ouch.
Great Video - i`ve learned something today!
Please tell us the release Date of the next 7" of iflight? Eg. Chimera 7 pro HD v3
Is anyone else having trouble binding the TX16S with Crossfire to the to the quad?? The goggles to the 03 air unit went smooth but I'm having no luck with my controller to the receiver. If you could make a quick short video of you doing that part real quick I would be beyond gratefull. I have the TBS version.
Good video but Joshua should post more dance content and dance tutorials
what about the power and battery tabs? i'm upgrade the firmware to 4.4.2 ... and now the battery still beeping just in 24.9v to 20v as low battery... i fly with 1500mah 6S 4.35v per cell.... somebody knows the amperage volts scale of the ESC? this is a SPAN F722-BT-HD V2 Stack
thankssss!!!
Hello, do you plan on reviewing new Walksnail goggles? Thanks :)
JB, I don’t always pay attention though I don’t remember if/when you mentioned when you’re back doing Q&A. When can the Beautiful Sausages expect a resumption of normal service? 🤔 (Happy Halloween 👻🎃)
th-cam.com/video/8gJTFdS378o/w-d-xo.html
Thank you 😊
Do you have a video on the descriptions of all the OSD fields?
th-cam.com/video/ki5n3DzKK_c/w-d-xo.htmlsi=y5z3GP3oPND6P65T
Great video Joshua, I was setting up mine when your video got uploaded😂 but i noticed that my quad got shipped with NMEA protocol for the GPS🤔🤔🤔
Thank you for showing how to switch to HD OSD mode on O3 and goggles 2👍
does anybody have the betaflight 4.5 version CLI/setup, with PIDs and everything? because apparently betaflight 4.4 has issues with GPS (what moz7 ships with). I tried running my backup 4.4 on 4.5 and it only set some of the things, did not set PIDs (and who knows what else...)
my moz7 is not showing up on BF , my computar cant detect it , but it detectect the 02 unit , can you help
it is good practice to have horizon mode on a switch so that it can be used in the rescue mode
I’d rather put angle mode on a switch instead of horizon mode. To me, horizon mode is like what you’ll find on toy drone, where it stabilizes itself but then does flips and rolls automagically with the push of a button
@@MrAlucardDante i got confused between angle and horizon, i've got angle mode as well in my gps rescue routine!
Hello, I know you have heard it before a thousand times from everyone else but one more time won’t hurt. THANK YOU for teaching us something new everyday. I wathced this video and I have a quick question for you, the presets you showed specially the cinematic one. Can that be applied on any drone like mark 5 for example or is it only good for the Moz7?
You can apply the rc link preset to any drone.
@@JoshuaBardwell so i know im a little too late to the party and this video is not so new, so in the video you reference the "based on the 533 racing rates for cinematic" which is what i like to fly. however i don't see that one listed anymore. do you have one equivalent tothat one that is good for cinematic and also since now we are on 4.5 and a lot of the say. 4.3, 4.4 but I'm on 4.5, what is the deal with the backward comparability? sorry man, total noob over there (3 weeks old to be exact lol)
1:14 Chris Rosser is cringing right now watching this video and seeing those wobbly antennas. 🤣
The flywoo85 o3 lite flies better than amazing. The trade off being how fragile it might be, I would shlum myself if we saw a JB review on it.
Hey Joashua, i copied your setup from pastebin and pasted it into Betafligh 4.3.2 CLI. Now I have no more information in my DJI Goggles 2. can I delete the setup again ?
JB’s HD OSD is meant for BF 4.4. You either have to upgrade you firmware, which I recommend only if you know what you are doing, or revert your configuration. Hopefully, you backed it up
@@MrAlucardDante
Thank you very much for your help. I was able to solve it with the following code :)
set osd_displayport_device = MSP
set displayport_msp_serial = 0
Grande Joshua❤
hey buddy,
any chance i could have access to your cinematic rates?
I use 533 rates.
@@JoshuaBardwell I don’t know but where can I find them ?
Awesome video, I'm actually on the market for a long range beside the Chimera and the Moz I'm also looking at the Rekon7 acn you please maybe do a review on that one, also I was gonna purchase a Elrs module or crossfire for my X9D+ but coincidently it literally caught on fire yesterday, so now I gonna purchase the Boxer Max but want to know aboult Elrs long range capability since is 1w how does it fair, can you test it out of the box, what u think? Thank!!!!
That's crazy your radio caught of fire! ELRS at 1w and a packet rate under say 500 should outrun your video unless you've done a lot of customizing on your video range. It's way more than most people need but if you do need more range it's very versatile so you could do some stuff to squeeze even more out of it. Hope that helps!
@jonah6496 thanks for the info it helps to know, yeah it was scary moment the flame went up and it reached the roof the super good thing is I get to buy the Boxer Maz😁
Great video as always. Just want to point out that I do use horizon mode bit I call it Karen mode if u know what I mean 😊
Just subtle enough without being too disturbing! Love your comment lol!
that thing is freaking huge
still no Freestyle v2 VTX review?
I released a review when it first came out, but then Chris Rosser discovered the initial review units were defective and not outputting the correct output power. As a result, I took down the review, because I don't want to spread inaccurate information.
When I have a unit that I am confident is not defective, I will review it.
@@JoshuaBardwell happy to hear that
loving it❤😂
Yes Joshua def need a updated crsf video/ what firmware actually work. I'm looking at 7" next
Yes. JB!
we need a walksnail avatar goggles X review
love geprc!
I thought you were out for a bit? or is that just the livestream? OMG Bardwell what have you done to me? I just built another 5" and I have 2 7" inch frames ordered.
I ordered a Crocodile and a AOS UL7
Congrats on the 300k subscribers, Joshua! 😃
But yeah, I noticed how excited you get when you say that you're going to use the Betaflight configurator! 😂
Anyway, stay safe there with your! 🖖😊
Biiiig I’m gonna learn something today guy…iykyk ;)
Who is this guy? He looks familiar. Like he used to be a TH-cam guy a while ago.
who better than Bardwell? Nobody.
god bless you
Thx,you cool!
Heck ya and I’m the new guy. Lol
I wish they would stop using LHCP antennas on BNF's designed around the DJI O3, but I do love the Moz7 - the GoPro mount with the carbon plate is a great innovation and the side plates make the drone feel super finished - it's perfect for the long-range and medium-range cruising flights I like to do to get scenery shots here in the Andes.
Why lhcp bad?
Because you will get less range than you would by using a dual polarized antenna designed specifically for the O3 system. LHCP on the quad will work, it just won't take full advantage of the potential of the O3 system. For those using Goggles V1 or Goggles V2 it doesn't matter, and for those with G2, you have the option of using LHCP antennas via the Lumenier adapter, but those with the Goggles Integra are stuck with the built-in antennas which re not LHCP. Like I said, it will work fine, just not at the system's maximum potential.@@RandoManFPV
@@colibrifpv a gotchya. So it's not that lhcp is bad; it's jus that those BNF builds always use lhcp but the goggles don't use lhcp. And due to the lack of continuity you lose range yea?
Like the bnf being lhcp wouldn't matter if the goggles were also using lhcp right?
Yeah exactly, ideally you want to match polarization on both ends, goggles and quad. I am using Goggles Integra with these LHCP antennas from GEPRC on my Moz7 build and the range seems pretty good, but knowing I could get somewhat better range and penetration bugs me a little. I will try the long Flyfish antenna made for O3 and see if it makes any difference... @@RandoManFPV
@@colibrifpv hell yea thanks man!
without flight - Im crying
It's a setup guide. You can watch the review (linked in the description) if you want to see it fly.
hey
Damit!!!!! I got to stop watching 👀 my bank account is going going gone !!!
That thing looks huge those arms are so tiny
Not the first comment
1st!
🫡🥰