2022 Rig Complete. Ready to Wash
ฝัง
- เผยแพร่เมื่อ 6 ก.พ. 2025
- Still some fine tuning but we are functioning and kicking it off this week!!! Let’s go!!!!! #hustle #onemanonetruck #powerwashing #guttercleaning #roofwashing #softwashing #housewashing #evolution #walkthedog
I really believe putting that uniseal down low will leak and/or blow out. I think the uniseals should be used at the top of tanks. I would buy a bulkhead and have it ready to install just in case...... You're a beast working in the cold rainy weather! Keep the great content coming!
Let’s hope not. I do have a bulkhead that I should have installed before putting 100 feet of drain hose in there
@@powerfulimprovements I hope it works out just fine. Take care.
You'll only have about 2 psi on uniseal should be good to go. I have 55's daisy chained together all low install . no problems
Looking good Joe!!! ✌️✌️👍👍💪💪💪 the Rinse of Darkness!!🍺🍺🍺 wash on brother!!
What a setup....very nice. You literally have thought of everything
She’s a beast
Hey Joe highly recommend a can of Fluid Film spray to protect against corrosion. Can pick them up at Autozone ect or any plow/trailer supply store. Spray that stuff on all your electronic terminals, any steele surfaces, everywhere. It protects against corrosion especially from SH bigtime.. It's Lanolin based product. It's really a game changer. Swear by that stuff to protect against SH.
Great idea
Like set up .... Have to watch again for plumbing . I think I'm going to incorporate some of your ideas.. Well thought out💪👍
Looking good sir. Can’t wait to start the season and follow along with you!
Thank you Big Rob
Still crushing it!!! Learned a couple of things. Thanks
😂✌🏼❤️
Hey Joe, Looking great man, We all can't wait to be running full speed again. I had a thought on your hose reel power supply through your mounting shelf. Instead of silicone maybe a piece of 1/4 inch fuel line with a slit in the side to encase your power wire. Should hold and protect it. BTW You and Carmody's antics got me through the winter. Thank you LOL! Take care!
That’s genius. I simple slit. 🤷🏼♂️💥
Excited for you Joe can’t wait to see the rig in action! Be careful not to lay any metal on your open battery terminals. Wash on Joe‼️
I’m going to cut a lid to fit
Great job on explaining everything! Thanks for sharing!👍
Looks great Mr. Deery. Wish you a great and safe season. #WashOn
Much appreciated Cliff
What s sweet set up this year Joe! You put a ton of thought into it and it really shows. Great work! 💪
Thank you
Joe, I don’t know if you remember it but I’m proud to be one of your first subscribers and I got to tell you; I’m so happy for all of your accomplishments and experience acquired in those short years. Congratulation and keep going strong. have a great season!
Much appreciated. And thank you for following from the beginning. The evolution has been the most fun
Man, I still have to build my entire trailer from scratch and kind freaking out about time/calendar
Your build looks amazing!
One day I’ll have everyone on the truck.
Yes it’s stressful not having it done. Always a little issue and time consuming
I’m in the same spot now. Just placed a big order of supplies and will be building a machine with a used gx390 engine and a 4.8 gpm canpump. I am only using a 25gal buffer tank since this build will need to be lightweight as possible because it’s going on the back of a 96 ford ranger. Did you get your build finished?
@@warriorofgodfitness488 I did get it built in time. My first job was April 1st last year… This year I moved some things around inside the trailer to create more room and make everything look nicer… Good luck to you and your build
That’s awesome and thanks. I plan to make a cheap little metering valve to hook to my downstream like in this video. I’ll try it and run some draw test to see if I can get the mix like I want.
Nice setup!!!
Looks awesome Joe. I hope to get started washing real soon. Weather hear in South Western Pa is getting better hopefully the sun break's through soon. When we get nice day's it comes with a lot of rain 🌧️☔
Thank you Rick
Looks good Mr Joe. Tomorrow I’ll send you a video the way I have mine set up through my proportioner and I can rinse the sud sucker just opening a valve.
Yeah. I had it set up that way last year. Had to separate cuz can’t run both systems at same time. I need to bae able to roof wash while someone else runs house wash
@@powerfulimprovements I thought you did.
Don’t forget to put the tarp and heater on 15 minutes before leaving to thaw the rig out! Looks good. I think you’ll be able to wash faster this year!
Great idea
I plumbed a three way valve off my proportioner so I can send my mix to either my 12 volt, or to my downstream injector. Works great.
Yes. That’s what I did last year. But can only use one system at a time that way. Had to separate so I can have helper house wash while I roof wash
@@powerfulimprovements Yeah that's a good point. Been enjoying watching your rig come to life this season.
Can you show how you put together that new downstream set up lol
A lot of great thinking there Joe!
Thank you!
Flipping sick man!! Can't wait to see that bad unit in action 🤘
✌🏼👊🏼💪🏼
Ive never use a uni seal on the bottom of the tank. Interesting. We've only used them to drop tubing down into the tank directly through the uniseal (no fitting)
Hopefully it holds
First! 🤣 Looking great Joe!👍
Square tanks brand name or where from?
I just 3-wayed the output of the blend valve to pull thru 12v or DSI (like you have but not going to your soap tank)
👍💯🙏✌️
Yeah. That’s how I was set up last year but couldn’t use both systems at the same time and it seemed like I was always forgetting to switch it back. So separate this year
Yeah, that’s an excellent point! I may be forming a deal like ole’ Mikey has with twin meters and dual injector.
My second wash job was problematic with a brand new 5.5 pump installed (tested fine) and then acting up at the job. Gonna take valves completely apart and reseal everything, gonna split it 2x2 instead of one set of 4 valves (w/soap in SH) til I get better valves from freedom softwash.
💯💯💯💯
Purging - we found that placing the check valves for each supply line as far down the tubing towards the tank as possible. This way the water, soap, sh, etc is stored in the tubing st all times vs. the way your check valves (like many others) are.
Brian Shipley at Midwest can hook you up with a proportioner for your downstream. I have a remote downstream that allows me to pull directly from my soap tank with a proportioner valve so I can do soap or not with a Crack of the valve..love his stuff..looks good Joe but I agree with one of your other commentors..I wld have a bulkhead on the bottom of that tank..I have used uniseal fittings now for last 2 years and love them!! But they have their limits and all that weight and flexing in the bottom of your tank just make sure to have backup..wld hate to see you without water..keep up the awesome work and as usual thanks for sharing!!
Yep. I have a call in to Brian And a 1 inch bulkhead on the truck in case
ahaha love the tumbler!
Thank you
Lookin good! I switched to a dual barb and T’ed off one side for controlled soap or degreaser. I also (after 3.5 years) finally put on a bypass so I’m not removing the ds or being lazy and leaving it on. Major fail not doing it sooner
I’m seriously considering a dual Barb
Where and what brand is the rigid yellow hose purchased at? I don't see many guys using the NH3 hose so great job using that. If you ever need more distance with your 12 volt just run two pumps in parallel for volume or in series for pressure. I do this quite a bit and is nice to be able to run 7 gpm or 14 gpm.
Thank you
John Doherty
LykeNew Power Wash
Salina Kansas Location
I bought it at a local agriculture store. I may try dual pump. Thank you for the advice
Great idea with the ds mixer!
Thank you
Yeah man your rig is set up pretty sweet this season. I know you are busy but if you ever get a chance to try that blue gun on your 5gpm machine wondering how that would work. I have yet to jump to a big machine. If anyone else has let me know.
Maybe once I set up my trailer
Looks great. What has tank did you use and what fittings did you need to connect it to your pressure washer engine? Looking to do the same.
I saw a YTV of a guy that had a banjo off the 12v reel in line and the DSI and he'd just swap out 1 to the other and pull from the same proportioner to either system as the job called for. Which is good if it really does work properly because then you can still use the flow pro for either 1. I'm trying to eliminate the need for 2 proportioners myself.
😂😂😂 that was me last year. Had to separate so both systems can run chem at same time
Joe i like that trailer in the background where did you get it from
That little trailer is about 25 years old. Need to pull behind an ATV. It was handed down to me from my father-in-law. I’m not sure where it came from.
Do you have a video of how to build your current proportioner vavle with a parts list?
Sorry no. Bought not built
Hi Joe,
Looking good.
Michael C - (WA)
Thank you
That downstream proportioner is next level.
😂 it a concept at least
@@powerfulimprovements it’s a really good one I am thinking about how I can build one I just built a SoftWash one I feel like it’s possible to build it with only 2 valves and make them 1/4
Joe, are you still using your homemade downstream proportioner? I'm assuming the main benefit of this is to turn down your SH if the house isn't really dirty. Conserve on SH?
Yes. I’m still using it. I’ll try to remember to show it today
This fall, PI takes off truck bed to install 8x10 flat bed. Needs more room. It never ends man, but its always a good thing.
Correction. This fall PI buys a dually flatbed 😂
@@powerfulimprovements Thats what I got. WooHoo
@@DumbCarGuy jealous
Idk about those uniseals under the water line, makes me nervous!
Awesome video!! Really cool downstream setup too! Have you oiled your electric real chains this year. We try to at least once a year. Thanks Joe!
I have not! Thank you for the reminder
No problem. Bike chain lube is what I was told to use.
Who told you about using the rb65 gun with your pressure washer!?
Figured it out
@@powerfulimprovements smart cookie!!!!
Joe, where did you buy your vertical tanks from? Thanks for the great videos 👍 🦈
US Plastic
@@powerfulimprovements thank you
Why did u put the drain hose in the tank
So I can quickly dump water as needed. Fill buckets etc. relieve truck of weight
@@powerfulimprovements no it looks like there’s black pipe inside the tank threw the hole you cut in it
Hey Joe, What size tank a you running in this video?
275
What about the other 2 tanks?
I actually replaced the soap hose barb with a brass one
Hey Joe what size is the SH tank you got? Where did you get it from? Thanks
It’s 50 US Plastics
Quick question do you run 1 wire or 2 wire pressure hose? Also if you don’t mind sharing, where do you get your hose from?
1 wire. Pressuretek usually
@@powerfulimprovements thank you. Keep up the great videos I have learned so much by watching this channel!
The DS proportioner...did you see the link I sent you on messenger earlier today?
Not until just now! Thank you. I’ll be giving them a call
Do you have the link to it ? I would love to get one thank you
👏🏿👏🏿👏🏿👏🏿👏🏿
Awesome rig Joe, try putting a piece of 1/4 inch hose through a hole then run wires through that, safer than silly cone lol
Next time for sure
FlexZilla hose is a real pain in the butt. I regret buying it. Also I think those nylon fittings on your downstream proportioner won’t handle SH well at all.
Oh it for sure won’t last
It is stressing drilling holes lol
😆
number 8
💥😆
Mike C is your BFF?? Thought I was…..
😂🤷🏼♂️✌🏼❤️
on the 275 , I feel with it being so low and no nut on the back the pressure will blow it out. i guess we'll see. gob up the die electric . you might to a mini exhaust flap so water doesn't get in your muffler. why are you shooting chemicals over your dog and letting your dog walk in them??????? strange.
It’s just soap. No chem
And we were on Rinse Mode
@@powerfulimprovements eeeeeeeeee. not to be a karen just worry about mist and skin irritation .
30th! 😁
💥✌🏼
Awesome Joe ! Have you tried a dual injector ? Im the guy that sent you the pic on Instagram of the dual turbo nozzle I made 💪 . Tony would love that thing haha
Not yet. Thinking about it