ฝัง
- เผยแพร่เมื่อ 29 ก.ย. 2024
- Rebuilding the rear wheel bearings, new axle seal, new studs & gaskets.
Flange stud kit
cruiserteq.com...
Axle rebuild kit rear - Bearings and all seals
cruiserteq.com...
Rear axle special socket
cruiserteq.com...
Parrot Nose Pliers
amzn.to/3Klawz7
Cheap Torque Wrench
amzn.to/40M54Lh
Bearing Greaser
amzn.to/3lUVV4d
Grease for hubs
amzn.to/3KmluEP
Wire wheel for drill
amzn.to/40NZojT
Brake Clean
amzn.to/3U4HdUT
Anti-Sieze Lubricant
amzn.to/42LpnKu
Rear Calipers
amzn.to/3KlfEDD
#landcruiser #80serieslandcruiser #fj80 #80series
Good video overall man. But.... BEARING RACES.... if it's a emegency fix on the tracks sure reuse but when doing it as routine maintenance ALWAYS REPLACE BEARING RACE with the new ones that come with the bearing. Ps whoever has worked on those handbrake shoes has put the bottom spring in wrong location, it's supposed to be BEHIND the adjuster star wheel. Cheers
Thanks from 🇪🇹🇪🇹🇪🇹አመሰግናለሁ።
Good job. I just finished the same. Let's do the front axle of the car. With the axle hub
With the cone washers, unscrew the nuts leave them on the thread screw in both your 1.25 bolts enough so it creates a gap where the gasket is then screw 2 of the nuts back in itll bring the other 4 cones out enough to be free or free enough you can wiggle it with a screw driver do the same for the remaining 2 cone washers. Easiest way and works every time i got a rubber mallet for those cones and found it really hit or miss, this way always works.
Thank you. Once I get more time I can't wait to do this
Hey John, great video as always! I replaced the sending unit for the fuel pump, and the gauge is still reading wrong. Is it a ground issue that could be causing this still. If so, where would I look. 07 tacoma 4.0
This saved me, thanks man. 🙏🏽
Next time for the bearing seal use a brass punch from the inside through. Hit the wheel bearing and the seal comes with it. Cheers!
Great idea!
How did the studs ''pull out'' 3.20 - i thought they'd be threaded in and you said you'd already loosened the nuts at the start of the video - You also said 2 of the studs broke - how did you get the remaining parts out ? Thanks
just use a piece of wood from the outer hub section to knock the inner bearing & seal out in one go. In most cases the seal can be reused if in an emergency and the wood wont harm the bearing
Awesome vid! Also, thanks for listing the parts!
Great video! Helped me with mine on the old 75 series. Most things are the same but no abs ring for me 😅 thank you!
Glad it could help man!
The one part I was waiting to see was the stud removal and replacement and you sped it up! 😂
Haha my bad! I just took 2 of the nuts thread them both in one stud then tighten them against each other! After that you should be able to remove the stud+nuts as if it were a bolt. Just be careful because they can be stuck in the hub. It’s worth heating up the stud first before you try and back it off!
@@Adv4x4 thanks mate
Great video! Could you tell, what the purpose of those two juts on the axle shaft flange?
great video
Thanks!
Hey man how did you get the new axle studs in?
thank you very much.
Hey there! Just Finished R&R my Tacoma Driveshaft to Replace U Joints and Carrier Bearing. Your Video (A while Back) was a Big Help ! Wanted to Say Thanks
Awesome man glad it helped!!
Excellent video, very helpful, yes indeed, I will need to do this as well sometime soon. Thank you for posting!
So glad it was helpful!
A very informative and helpful video. Thanks!
Glad it was helpful! Thanks for watching!
that inner hub seals its aftermarket seal?. its looking more like the front inner hub seal.
Yes aftermarket seal I questioned it at first too but seemed all the same once I looked closer.
Awesome episode Buddy. While I am not very mechanically inclined I find your content very interesting and always informative. You provide very clear and concise directions which makes it understandable for the novice. Nice way to enjoy my Sunday coffee.
Appreciate it Mike! Hopefully it’s a very informative video for people looking to do the same repairs.
@@Adv4x4 It does inspire/ motivate me to take on more challenging repairs and service work on my truck.
Would be great to get the baselining on a couple of videos, is nice the driveway maintenance for the ones that want to tackle some of it on their own.
Hey man! Not quite sure what you mean?
I try to gear these videos towards people wanting to learn how to tackle this stuff on their own! The details can be a little much at times, but for someone wanting to learn it’s great!
@@Adv4x4 Hahaha I have no idea what I wrote!
First: I like that you show us how to get the maintenance done on the driveway.
Second: please keep filming all the maintenance, would be great to get a series of videos of it.
Third: I like the detailed videos!
Haha copy! Do plan to show more as I keep building this thing! Next video will be on steering link replacement as well as radius arm install!