Some people say that it works, others say that it doesn't work, that it's fake, but I think that there must be a way to make the magnetic forces to work, even if we don't know it yet!
Sheilding you need non ferrous material like Al to block the magnetic field at certain points in rotation to get past the draw back. Also the angle of your magnets can change the direction of deflection like a water jet. Funnel the magnetic field to a point that you want.
I spent about 10 years trying to build a magnet motor. My conclusion was that it is probably not possible and the reason is that a magnetic field is 3D and as any arrangements result in a zero net gain when you integrate all actions and reactions over the total magnetic field extent. Even though one gets powerful local actions/reactions in the end net gain is zero.
Yes exactly, that is what we thought to. The force needed to pass the magnet is the same as the force that will push the magnet away. Unless you could find a system that lifts the magnet up en releases it at the right moment to push away the rotormagnet it might work. Still there would be mechanical losses that would harm efficiency so it still cannot function. It would be interesting to know more of the designs and stuff you have done in those 10 years of research.
@@thebrojectlist6881 If you´re asking for more insight into my magnet trials just forget about it, you´d be wasting your valuable time. Think more in kinematik masses, rods and levers systems. - I´ve been thinking about my launching my own web page as I already have a TH-cam account. No less than two university professors have seen my basic idea AND they did NOT talk about thermodynamics after seeing it. Says a lot about the approach
@@hafsteinnhafsteinsson958 well it's very tempting to start experimenting, and make chances in design and all that. But then we would be another 10 years further, just like you😅 i would really like to see these motors run in real life that are going around on the internet, and so claimed free energy generator. It would mean that they made something that has more then 100% efficiency. Still, the experiment was fun, even just for some entertainment
@@thebrojectlist6881 No free energy motor so far has worked. Period. That does not proof that it will never be done. Once the earth was flat, people would never fly and the earth was the center of the universe. If you´re familiar with the movie "Imitation game" its punchline goes something like this : "Sometimes, its the people who no one imagines anything of ..... who do the things that no one can imagine". I do agree that collaboration is the way forward but what prevents it is mutual mistrust. Sad really. As you say my experience ought to shorten the path for a success for a pair of fresh eyes. Avoid pitfalls, the best formula for progress. I don´t waste my time on overunity solutions. It´s all or nothing, meaning "nothing in, extra", just nature and its forces. Like Tesla said, energy is all around us. It´s just a question of a way to tap it . . . .
there is anther setup magnets on two rings of plastic facing(like an eye ) repelling each other between the two free rotating rings a short piece of steel , both rings will attract to it first but as soon as the steel piece no longer separate them they will repel each other which will keep them rotating
You don't need a wave and ball bearings, it floats in the repulsive magnetic field. Important are the angle and above all the shielding to specifically direct the repulsive force.
It would be really hard to balance it without a shaft and bearings. Even if it would work it would be pushed out of the side. You could use a magnetic bearing to reduce friction but the design in general should change.
Take a look to Muammer Yildiz magnet motor. It's a different principle of your idea of magnet motor. Anyway congratulations for your work. Experiment 2019 of Belluno Italy. You have to study magnetic fields very well.
For 15 years, I have been working with angular resonance and I am ready to do the electricity generation project together with investors who agree to make an official protocol. Everything will be done openly after the signatures are signed.
@@thebrojectlist6881 I want to create a clean energy system for a cleaner world. You can promote this project in your country. I want to realise this project and get a worldwide patent. Of course, I need a solid and idealistic investor to realise this work. I convert angular energy into mechanical and electrical energy. I am an inventor. I am ready to do this project in any country that will support me. 98% of the published videos are wrong and do not work. I know the mistake they all make.
Ok, that's a good idea, but why don't you build it inside the shaft housing itself? Even if you need more strength, do the combination inside and out. This reduces everything and you can save material. Also note a weight of momentum when translating. Sometimes you don't even need a high magnetic field?
It results in the same problem. The magnets have to overcome to much resistance force. We are currently working on a new design. Keep an eye on our channel
Diamagnetic These are materials that, if placed in the presence of a magnetic field, have their elementary magnets oriented in the opposite direction to the direction of the applied magnetic field. Thus, a magnetic field is established in the substance that has a sense opposite to the applied field. These are diamagnetic substances: bismuth, copper, silver, lead etc.
ok maybe this info will help you will need 3 rotors and 3 clamps ,the 1st rotor is magnets north and the other 2 they are south now for magnet spacing around the rotors , line all 3 rotors up one on top of another and draw a straight line from rotor 1 to rotor 3 ,this is the o/o/o degree position (the rotor diameter must allow for any number of magnets dividable by 3) now make a mark at the 0 position on rotor 1 ,measure around rotor 2 -180 degrees make a mark ,on rotor make a mark at 360or 0 degree position. Now rotate all three rotors together to the position of the second magnet on rotor #1 and repeat do this for as many positions as you have magnets on the rotors ,now do the same on the clamp parts, If you know anythink about electricity you will know that the positions of each row of magnets along the 3 rotors represents a position on a sine wave or a Archimedes screw ,the angle of the magnets is about 12 degrees on the wheel.
How many different configurations do people have to arrange magnets in to realize that what they are hoping for simply will not work. Motors powered by magnets is a fiction. There is no energy available from a magnet to do work, and magnetism isn't a form of energy-it's a force. Any motor claiming to be powered by magnets is fake. Every single one. Honestly, the basis of why these type of magnet arrangements will never spin continuously or do work was introduced 350 years ago-but people keep trying. It's good for the magnet industry, I guess. ;)
@@thebrojectlist6881 There is no such thing as a single pole magnet. All magnets have a North and South pole. Physics talks about single-pole magnets, but only as a thought experiment.
@@n45h26 I have tested the link with other computers and they all work. Maybe you can surf to www.thingiverse.com/ and use the search button with the following words: "Magnet motor" or "Thebrojectlist"
Mu metal shielding missing & The stator mags are incorrectly polarized. Looks like You got the red herring design like many others. And if you get it to work remember to not have it in repulsion mode as that kills neos real fast!
I tried to make one but failed. The main problem I faced is the attractive force of magnets .So I tried MU metal to shield the attractive force of opposite poles ,no use. So I stopped the experiment ..We need strong material which can prevent the attractive force of magnets to make this device a succesful.
Magnetic fields can't be passively shielded, they can only be redirected. Any redirection of the field will interfere with the flux from nearby magnets making this impossible. You can buck a permanent magnet with a powered coil, but now we're back to motors powered by electricity.
The second design on the white board probably has to much friction because of the camshaft. Maybe if you would make something with a magnet that can turn on and off?
Nice idea, but the principle remains the same. The forces of the two attracting magnets equal the forces of the two repelling magnets, therefore it remains still just as the single engine I made.
hi, if you have resource, why dont try make magnet weel, like water weel. magnet push each other 45 degree angle. Or put magnets in cirkle, glue to a piece of wood, or plastick and make like mill. if magnets moves araund can make somting like wind generator. Sorry my bad english.
you need to turn the outer ring of magnets 90 degrees so that the inner ring magnets are at a 90 degree angle to the outer ring magnets currently, you have the outer ring magnets at 180 degrees from the inner ring not sure if you can get away with re-using your outer ring magnets to do this note: i have not tested this myself, but the guy from `Magnet Motor News` and his other channel provide quality information
@@thebrojectlist6881 please bare in mind, that no-one has been able to replicate the results of the perendev motor, theres also a similar patent to what you are doing in this video in india i think [ 2016 ]. I remain hopeful for a PMM, however, the more and more research I do, is it becoming evident to myself that it is not yet possible, or if it is, it is a heavily guarded secret.
a very simplified version of what i've found is all of the available videos online are either intentionally deceiving the viewer, or the person who uploaded the video does not have a basic understanding of electricity. I do not mean this as a dis-respect to them, as I myself was there and still am, but I have enough knowledge to debunk [ for a lack of a better term ] just about any of the videos that are simple. Here is an extremely simple gauge [ which im sure many are aware of, but hopefully someone that is reading this does not know and therefore can be guided ] if the input wattage is less than the output wattage of a device, then it is a free-energy or overunity device watt = amp * volts [ amp is also known as current ]
@@codyquist4908 Yes that is the same conclusion that I have made. The only way to really "debunk" the fake videos is to recreate them and explain why it is not working. However people will always agrue that you did something wrong in your design. I'm still searching for alternatives "it's always seems impossible until it's done".
@@thebrojectlist6881 I think the best way to look at it would be the mindset of Ben Franklin. " I didn't fail to make a lightbulb 2,000 times, I found out 2,000 ways how not to make a lightbulb". This sounds very simple, but belief is very powerful. This is different from determination. [ im not saying build the perendev motor 2,000 times lol, but rather fe/ou ] I appreciate you taking the time to create this video and showing your results, however, it lacks the most important piece of the puzzle, the magnetic arrangement.
this has rried before having two, you need a micro controller to program the repulsion force at right time to give that extra differential changes is the best way
I already tried the 2 disc version long ago and they lock up as well, the thing with a magnet motor is that even if you get it to rotate it does not have any torque, you would need a massive 300 kg or 150 kg force magnet for a smaller generator due to the force generated backwards when a load is put in the generator which generally is much larger than those of a permanent magnet
There are correct plans and red herrings! Dont give up. You dont have the correct stator magnets they need to be horizontally polarised. and even if it did ever work ,which it did , make sure you dont use repulsion mode! that kills neo mags in a short time.
Simple. Magnets must be placed rather tangential /angled instead of vertical to the midpoint to be Pushed Further and Further and Further....in one direction.
It does not work at best it is a converter of translational movement in rotational movement! you have to bring energy! If it runs for the duration of the movement, the inertia will do the rest but it will necessarily stop.
Nice try, but magnets are always in equilibrium, meaning nothing gained nothing loss. The only way to make it work is with nonlinear magnets. But I don't know of any, except electromagnets, but that mean you need an electric current to make it work. That becomes an electric motor.
Great skills with 3d programing and 3d printing. Are you still working on this project? Greet from Ukrain Kharkiv city of Rockets and Cosmic electronik
Yes I'm still working on other designs, I did an update video if you haven't seen it already. "Magnet motor v2 update" th-cam.com/video/1tXThYMc7jc/w-d-xo.html
I have tried with the different setups of repulsive and attractive but this design didn't work. I made it this big to have a flywheel like advantage to keep it spinning. But this didn't help.
3 different errors made, magnets should have a cut of 45 degree and placed in a specific angle and a corner should be shielded with a mu metal or nickel foil then you will have results
you built it WRONG. 1st of all you have the magnets ALL at the same height on the rotor. You are supposed to have the magnets in a step formation. 1st magnet flush to top 2nd magnet deeper in plastic 3rd magnet even deeper in plastic and so on. It has to be this step down formation. ALSO , on the outer clamp together magnets you have to have 2 magnet spaces where there are NO MAGNETS and that would be on the top where you clamp it together. ALSO , The force of the magnets must be great enough to make over 1/2 half of a turn to repeat cycle to spin past the area that has no magnets on top. ALSO you need enough weight on the rotor so it spins like a top does, less friction. You have that large beiring. NO NO The clamp magnets MUST ALSO have the step formation. The rotor step formation clockwise and the clamp magnets counter clockwise. THE WEIGHT of the rotor MUST BE heavier than the pull of the neodymium magnet force. IF you get these things correct it will continue to spin at a high velocity. See what happens is as the rotor spins to the top , the magnets that are closer to the outside and the weight gravity force the rotor down. IT then picks up enough magnetism to bring the rotor back up and the weight of the spinning force breaks free from magnet power on top to start the cycle all over again.
Thank you for your reply. It would be interesting to see what happened if we adopt your suggestions. We are still working on different models, we might as well try your method.
You should abandon that concept completely. And watch ( James Ronie stater's ). His ideas, are completely, different than most. I would do something like he is doing. Study his ( stater's, HOW TO BUILD IT )!! I REALLY BELIEVE THEY'RE THE WAY TO GO. He's on "UTUBE" by the way.... Good Luck 🤞.
Çà ne marche pas au mieux c'est un convertisseur de mouvement de translation en mouvement de rotation ! il faut amener de l’énergie ! Si il tourne le temps du déplacement l'inertie fera le reste mais cela s'arrêtera obligatoirement.
You don't know how to put magnets. It has to be what the size of the magnets is bigger than that and the magnet poles should be all north or all south try again he's working
The problem with the idea that magnetic motors are free energy machines is that you end up loading magnets in repulsion to other magnets, and over a long period of time, this causes magnets to slowly demagnetize. Basically, you end up using up your magnets as a sort of battery, and the amount of energy it takes to re-magnetize them is greater than the energy you get out of the system. There's also a more fundamental problem that was figured out in vector calculus. If you want to get some kind of torque out of that system, you need a field that has "curl"; fields with curl are non-conservative. However, magnets produce fields that have no curl. You cannot create a field with curl out of assembling components that do not have curl, as far as I understand. It is mathematically impossible. You would need magnets to behave differently than they behave to produce fields with different qualities.
No non funziona per il fatto che troverà un suo punto di equilibrio. Troverà una fase crescente fino a non superare il punto massimo. Non può funzionare
DESCOBRIR : O PRINCÍPIO DA ; ROTAÇÃO ; MOTO - PERPÉTUO ; É : À : ROTAÇÃO : PRINCÍPIO ?? ; DO MOVIMENTO : ROTAÇÃO ; É !!! ; À ; DESCOBERTA ??? ; PRINCÍPIO - ROTAÇÃO - MOVIMENTO - ROTAÇÃO ; DESCOBERTO ; SEGREDO : TUDO !!!!. MAGNETO : ROTAÇÃO : MOTOR . 😲😲😃😄😃💡💡💡💡☝️☝️☝️😄😃
thanks for your honest work
Some people say that it works, others say that it doesn't work, that it's fake, but I think that there must be a way to make the magnetic forces to work, even if we don't know it yet!
All electric motors work by magnetic fields. There has to be a way.
@@johnlatsch9720 Yes, indeed. I agree with you. There has to be a way!
I'm still working on other designs that are more promising.
Sheilding you need non ferrous material like Al to block the magnetic field at certain points in rotation to get past the draw back. Also the angle of your magnets can change the direction of deflection like a water jet. Funnel the magnetic field to a point that you want.
it is only necessary to position the pole in front of the other, isolating the sides that work as brakes with diamagnetic insulator
I spent about 10 years trying to build a magnet motor. My conclusion was that it is probably not possible and the reason is that a magnetic field is 3D and as any arrangements result in a zero net gain when you integrate all actions and reactions over the total magnetic field extent. Even though one gets powerful local actions/reactions in the end net gain is zero.
Yes exactly, that is what we thought to. The force needed to pass the magnet is the same as the force that will push the magnet away. Unless you could find a system that lifts the magnet up en releases it at the right moment to push away the rotormagnet it might work. Still there would be mechanical losses that would harm efficiency so it still cannot function. It would be interesting to know more of the designs and stuff you have done in those 10 years of research.
@@thebrojectlist6881 If you´re asking for more insight into my magnet trials just forget about it, you´d be wasting your valuable time. Think more in kinematik masses, rods and levers systems. - I´ve been thinking about my launching my own web page as I already have a TH-cam account. No less than two university professors have seen my basic idea AND they did NOT talk about thermodynamics after seeing it. Says a lot about the approach
@@hafsteinnhafsteinsson958 well it's very tempting to start experimenting, and make chances in design and all that. But then we would be another 10 years further, just like you😅 i would really like to see these motors run in real life that are going around on the internet, and so claimed free energy generator. It would mean that they made something that has more then 100% efficiency. Still, the experiment was fun, even just for some entertainment
@@thebrojectlist6881 No free energy motor so far has worked. Period. That does not proof that it will never be done. Once the earth was flat, people would never fly and the earth was the center of the universe. If you´re familiar with the movie "Imitation game" its punchline goes something like this : "Sometimes, its the people who no one imagines anything of ..... who do the things that no one can imagine". I do agree that collaboration is the way forward but what prevents it is mutual mistrust. Sad really. As you say my experience ought to shorten the path for a success for a pair of fresh eyes. Avoid pitfalls, the best formula for progress.
I don´t waste my time on overunity solutions. It´s all or nothing, meaning "nothing in, extra", just nature and its forces. Like Tesla said, energy is all around us. It´s just a question of a way to tap it . . . .
@@hafsteinnhafsteinsson958 Well, there are a lot of people who no one imagines anything of. How to pick the promising one?
Without shielding, the field works in all directions, with shielding you can specifically let the field work.
I tried with shielding but there was no difference. Some people advised me to use Mu metal but I think the design should change.
The original motor has 3 rotors to work. Also shielding should be on back edge leaving of magnets to work
there is anther setup magnets on two rings of plastic facing(like an eye ) repelling each other between the two free rotating rings a short piece of steel , both rings will attract to it first but as soon as the steel piece no longer separate them they will repel each other which will keep them rotating
You don't need a wave and ball bearings, it floats in the repulsive magnetic field. Important are the angle and above all the shielding to specifically direct the repulsive force.
It would be really hard to balance it without a shaft and bearings. Even if it would work it would be pushed out of the side. You could use a magnetic bearing to reduce friction but the design in general should change.
The magnets act like springs. If you can replace your magnets with springs, and it still looks like it might work, then you might be onto something.
interesting thought, but making the spring compress again after repulsion would probably absorb all the energy don't you think?
@@thebrojectlist6881
Yes, like magnets.
Take a look to Muammer Yildiz magnet motor. It's a different principle of your idea of magnet motor. Anyway congratulations for your work. Experiment 2019 of Belluno Italy. You have to study magnetic fields very well.
Thank you, I have been looking in to that type of magnet motor. I will keep you up to date if I have a breakthrough.
Master class! Super!
For 15 years, I have been working with angular resonance and I am ready to do the electricity generation project together with investors who agree to make an official protocol. Everything will be done openly after the signatures are signed.
That is really interesting, I am curious about the results. I will keep an eye on your project.
@@thebrojectlist6881 I want to create a clean energy system for a cleaner world. You can promote this project in your country. I want to realise this project and get a worldwide patent. Of course, I need a solid and idealistic investor to realise this work. I convert angular energy into mechanical and electrical energy. I am an inventor. I am ready to do this project in any country that will support me. 98% of the published videos are wrong and do not work. I know the mistake they all make.
@@thebrojectlist688198% of the published videos do not work. I know the mistake they all make.
@@thebrojectlist6881Thank you.
@@thebrojectlist6881 Thank you very much.
Ok, that's a good idea, but why don't you build it inside the shaft housing itself? Even if you need more strength, do the combination inside and out. This reduces everything and you can save material. Also note a weight of momentum when translating. Sometimes you don't even need a high magnetic field?
I'm amazed by three D printing.
Y que pasaria si los imanes van con una inclinacion diferente
It results in the same problem. The magnets have to overcome to much resistance force. We are currently working on a new design. Keep an eye on our channel
The angle is also important, on both inside and outside.
for the angle of the magnets I used 33 degree that was what the internet believed was the sweet spot
@@thebrojectlist6881
Can I get STL of this model? thingiverse links are broken
I have checked the link and it works fine with my computer. You can try it again if it still doesn't work I can e-mail them to you.
Diamagnetic
These are materials that, if placed in the presence of a magnetic field, have their elementary magnets oriented in the opposite direction to the direction of the applied magnetic field. Thus, a magnetic field is established in the substance that has a sense opposite to the applied field. These are diamagnetic substances: bismuth, copper, silver, lead etc.
ok maybe this info will help you will need 3 rotors and 3 clamps ,the 1st rotor is magnets north and the other 2 they are south now for magnet spacing around the rotors , line all 3 rotors up one on top of another and draw a straight line from rotor 1 to rotor 3 ,this is the o/o/o degree position (the rotor diameter must allow for any number of magnets dividable by 3) now make a mark at the 0
position on rotor 1 ,measure around rotor 2 -180 degrees make a mark ,on rotor make a mark at 360or 0 degree position. Now rotate all three rotors together to the position of the second magnet on rotor #1 and repeat do this for as many positions as you have magnets on the rotors ,now do the same on the clamp parts, If you know anythink about electricity you will know that the positions of each row of magnets along the 3 rotors represents a position on a sine wave or a Archimedes screw ,the angle of the magnets is about 12 degrees on the wheel.
How many different configurations do people have to arrange magnets in to realize that what they are hoping for simply will not work.
Motors powered by magnets is a fiction. There is no energy available from a magnet to do work, and magnetism isn't a form of energy-it's a force.
Any motor claiming to be powered by magnets is fake.
Every single one.
Honestly, the basis of why these type of magnet arrangements will never spin continuously or do work was introduced 350 years ago-but people keep trying.
It's good for the magnet industry, I guess.
;)
its called a Perendev magnetic generator
Good honest video. For those claiming you need to add more discs or whatever, they are wrong. This will never work.
Maybe if you have single polarity magnets (all north or all south) but that is also questionable if those are real.
@@thebrojectlist6881
There is no such thing as a single pole magnet. All magnets have a North and South pole. Physics talks about single-pole magnets, but only as a thought experiment.
Hola dónde bajo los stl?? Gracias
www.thingiverse.com/thing:5158832
Sometimes it depends on the type of webbrowser you use for the link to work. Normally if you use chrome it should work.
@@thebrojectlist6881 what a pity :(... I use chrome and it doesn't work :( is it difficult for me to send it to an email or another link?
@@n45h26 I have tested the link with other computers and they all work. Maybe you can surf to www.thingiverse.com/ and use the search button with the following words: "Magnet motor" or "Thebrojectlist"
can I hazard a guess that the magnets were too weak and too far apart?
The magnets might have been to strong or the placement could be of. We are still working on different models. But thank you for your guess.
Mu metal shielding missing & The stator mags are incorrectly polarized. Looks like You got the red herring design like many others. And if you get it to work remember to not have it in repulsion mode as that kills neos real fast!
Bullshit
I tried to make one but failed. The main problem I faced is the attractive force of magnets .So I tried MU metal to shield the attractive force of opposite poles ,no use. So I stopped the experiment ..We need strong material which can prevent the attractive force of magnets to make this device a succesful.
Magnetic fields can't be passively shielded, they can only be redirected. Any redirection of the field will interfere with the flux from nearby magnets making this impossible. You can buck a permanent magnet with a powered coil, but now we're back to motors powered by electricity.
Bisa beli dimana pak
The second design on the white board probably has to much friction because of the camshaft. Maybe if you would make something with a magnet that can turn on and off?
" make something with a magnet that can turn on and off" Like an electric motor for example.
Con uno no sirve tienen que ser cuatro podrías probarlo con cuatro 🧐🧐🧐🧐
Nice idea, but the principle remains the same. The forces of the two attracting magnets equal the forces of the two repelling magnets, therefore it remains still just as the single engine I made.
hi, if you have resource, why dont try make magnet weel, like water weel. magnet push each other 45 degree angle. Or put magnets in cirkle, glue to a piece of wood, or plastick and make like mill. if magnets moves araund can make somting like wind generator. Sorry my bad english.
I'm still working on other designs, you can watch the second video "magnet motor v2 update": th-cam.com/video/1tXThYMc7jc/w-d-xo.html
Just make the tri angle base a little bit larger
you need to turn the outer ring of magnets 90 degrees
so that the inner ring magnets are at a 90 degree angle to the outer ring magnets
currently, you have the outer ring magnets at 180 degrees from the inner ring
not sure if you can get away with re-using your outer ring magnets to do this
note: i have not tested this myself, but the guy from `Magnet Motor News` and his other channel provide quality information
Thank you, I will look into this
@@thebrojectlist6881 please bare in mind, that no-one has been able to replicate the results of the perendev motor, theres also a similar patent to what you are doing in this video in india i think [ 2016 ]. I remain hopeful for a PMM, however, the more and more research I do, is it becoming evident to myself that it is not yet possible, or if it is, it is a heavily guarded secret.
a very simplified version of what i've found is all of the available videos online are either intentionally deceiving the viewer, or the person who uploaded the video does not have a basic understanding of electricity. I do not mean this as a dis-respect to them, as I myself was there and still am, but I have enough knowledge to debunk [ for a lack of a better term ] just about any of the videos that are simple.
Here is an extremely simple gauge [ which im sure many are aware of, but hopefully someone that is reading this does not know and therefore can be guided ]
if the input wattage is less than the output wattage of a device, then it is a free-energy or overunity device
watt = amp * volts [ amp is also known as current ]
@@codyquist4908 Yes that is the same conclusion that I have made. The only way to really "debunk" the fake videos is to recreate them and explain why it is not working. However people will always agrue that you did something wrong in your design. I'm still searching for alternatives "it's always seems impossible until it's done".
@@thebrojectlist6881 I think the best way to look at it would be the mindset of Ben Franklin. " I didn't fail to make a lightbulb 2,000 times, I found out 2,000 ways how not to make a lightbulb". This sounds very simple, but belief is very powerful. This is different from determination. [ im not saying build the perendev motor 2,000 times lol, but rather fe/ou ]
I appreciate you taking the time to create this video and showing your results, however, it lacks the most important piece of the puzzle, the magnetic arrangement.
this has rried before having two, you need a micro controller to program the repulsion force at right time to give that extra differential changes is the best way
Are the stl(s) available for download?
STL-files are available at www.thingiverse.com/thing:5158832
@@thebrojectlist6881 The link is broken
I already tried the 2 disc version long ago and they lock up as well, the thing with a magnet motor is that even if you get it to rotate it does not have any torque, you would need a massive 300 kg or 150 kg force magnet for a smaller generator due to the force generated backwards when a load is put in the generator which generally is much larger than those of a permanent magnet
There are correct plans and red herrings! Dont give up. You dont have the correct stator magnets they need to be horizontally polarised. and even if it did ever work ,which it did , make sure you dont use repulsion mode! that kills neo mags in a short time.
Read my comment!
We are currently working on a new design, keep your eyes on the channel
Simple.
Magnets must be placed rather tangential /angled instead of vertical to the midpoint to be Pushed Further and Further and Further....in one direction.
Thank you for your reply. However the magnets are placed under an angle of 34 degree. I have played with different angles all with the same results
I don't think the idea works, but with good marketing you could sell the idea.
It does not work at best it is a converter of translational movement in rotational movement! you have to bring energy!
If it runs for the duration of the movement, the inertia will do the rest but it will necessarily stop.
You need two rotors with a möbius strip ,
Nice try, but magnets are always in equilibrium, meaning nothing gained nothing loss. The only way to make it work is with nonlinear magnets. But I don't know of any, except electromagnets, but that mean you need an electric current to make it work. That becomes an electric motor.
Laws of thermodynamics...look it up.
Stl link is not working
The link works with my computer. You can try again. If it stil doesn't work, I can mail them to you.
Bonjour à tous : je voudrais le même appareils.... ou en trouver...? Ou l'hacheté....?
In the near future I will make the design and plans publicly available. So everyone can try or improve the design.
Thank you for showing us that magnet motor DOES NOT work ! There is NO such free energy !!!
Great skills with 3d programing and 3d printing. Are you still working on this project? Greet from Ukrain Kharkiv city of Rockets and Cosmic electronik
Yes I'm still working on other designs, I did an update video if you haven't seen it already. "Magnet motor v2 update" th-cam.com/video/1tXThYMc7jc/w-d-xo.html
Hello,how are you?
@@bobwuk3589 Hello i am refuged in Lviv from Kharkov. Still in Ukraine. Thanks to Jesus we are still alive.
hexagon in to pentagon with magnet shields
Why won't you sell it to me?
It is to expensive to ship. You can find the file on Thingiverse so you can 3d print your own motor. www.thingiverse.com/thing:5158832
you need to follow the v gate concept if it is going to work
Hello.. would you make a model and sell it on eBay and I could purchase one for you?
STL-files are available at www.thingiverse.com/thing:5158832
@@thebrojectlist6881 Link down
bearing problems
Workwith carbon you reach the weight by the weight of the magnets. Just make the layer on the outside, repulsive and attractive.
I have tried with the different setups of repulsive and attractive but this design didn't work. I made it this big to have a flywheel like advantage to keep it spinning. But this didn't help.
look at the ball and the position of the magnets at 2.40
th-cam.com/video/yng6gkzhA0A/w-d-xo.html
هل طريقته صح او خطا
Pretty fancy failure
3 different errors made, magnets should have a cut of 45 degree and placed in a specific angle and a corner should be shielded with a mu metal or nickel foil then you will have results
you sound like you built one
@@slawomirheluska2489
He sounds like he never built one :-)
Que tal si estuvieras enseñando matemáticas y no conocieras el cero?
! Its Not free energy !
Magnets are Create with energy, too
Don't forget it -> its more New energy :)
It isn't free energy because it doesn't work.
Add a heavy flywheel. Inertia will make it spin by the sticking point.
jsjsjsj parece facil verdad
Free energy like planet gravity attract space ship betwen its for powered that propulsion ....and so 😂
you built it WRONG. 1st of all you have the magnets ALL at the same height on the rotor. You are supposed to have the magnets in a step formation. 1st magnet flush to top 2nd magnet deeper in plastic 3rd magnet even deeper in plastic and so on. It has to be this step down formation. ALSO , on the outer clamp together magnets you have to have 2 magnet spaces where there are NO MAGNETS and that would be on the top where you clamp it together. ALSO , The force of the magnets must be great enough to make over 1/2 half of a turn to repeat cycle to spin past the area that has no magnets on top. ALSO you need enough weight on the rotor so it spins like a top does, less friction. You have that large beiring. NO NO The clamp magnets MUST ALSO have the step formation. The rotor step formation clockwise and the clamp magnets counter clockwise. THE WEIGHT of the rotor MUST BE heavier than the pull of the neodymium magnet force. IF you get these things correct it will continue to spin at a high velocity. See what happens is as the rotor spins to the top , the magnets that are closer to the outside and the weight gravity force the rotor down. IT then picks up enough magnetism to bring the rotor back up and the weight of the spinning force breaks free from magnet power on top to start the cycle all over again.
Thank you for your reply. It would be interesting to see what happened if we adopt your suggestions. We are still working on different models, we might as well try your method.
How does it work, you can see on the channel /O nosso Universe oficial/
You should abandon that concept completely.
And watch ( James Ronie stater's ).
His ideas, are completely, different than most.
I would do something like he is doing.
Study his ( stater's, HOW TO BUILD IT )!!
I REALLY BELIEVE THEY'RE THE WAY TO GO.
He's on "UTUBE" by the way.... Good Luck 🤞.
excellent, but , continue to try my language is portuguese, scuse-me
Çà ne marche pas au mieux c'est un convertisseur de mouvement de translation en mouvement de rotation ! il faut amener de l’énergie !
Si il tourne le temps du déplacement l'inertie fera le reste mais cela s'arrêtera obligatoirement.
Troverà il punto di equilibrio e si fermerà. Giocattoli
yeah i made a difrend one no luck
You don't know how to put magnets. It has to be what
the size of the magnets is bigger than that and the magnet poles should be all north or all south
try again he's working
I can't seem to find real single pole magnets or they are to expensive. I'm still working on other designs.
The problem with the idea that magnetic motors are free energy machines is that you end up loading magnets in repulsion to other magnets, and over a long period of time, this causes magnets to slowly demagnetize. Basically, you end up using up your magnets as a sort of battery, and the amount of energy it takes to re-magnetize them is greater than the energy you get out of the system.
There's also a more fundamental problem that was figured out in vector calculus. If you want to get some kind of torque out of that system, you need a field that has "curl"; fields with curl are non-conservative. However, magnets produce fields that have no curl. You cannot create a field with curl out of assembling components that do not have curl, as far as I understand. It is mathematically impossible. You would need magnets to behave differently than they behave to produce fields with different qualities.
No non funziona per il fatto che troverà un suo punto di equilibrio. Troverà una fase crescente fino a non superare il punto massimo. Non può funzionare
👍
È il motore di Perendev
DESCOBRIR : O PRINCÍPIO DA ;
ROTAÇÃO ; MOTO - PERPÉTUO ;
É : À : ROTAÇÃO : PRINCÍPIO ?? ;
DO MOVIMENTO : ROTAÇÃO ; É !!! ;
À ; DESCOBERTA ??? ; PRINCÍPIO -
ROTAÇÃO - MOVIMENTO - ROTAÇÃO ;
DESCOBERTO ; SEGREDO : TUDO !!!!.
MAGNETO : ROTAÇÃO : MOTOR .
😲😲😃😄😃💡💡💡💡☝️☝️☝️😄😃
Mu metal.
Read the Patents
Please indicate which patents
User MU metal ok
Waste of time.
Hade of donky