Yesterday my Xbox 360 Slim Cause this same Issue after Restarting and unplugged all the cables I turn it on again bit suddenly It Showed Red Dot And Some kind of Error Messege on the screen After turning it off and turn On again It worked Perfectly i played 2 hours with it . But today Same Green Power Light on but no display
AoA. Sir i admire your great work. I have xbox 360 slim. It turns on gives a green light (if controller is connected, the controller lights also keep blinking) the green light of console is constantly on but there's no display. However, the xbox sometimes gives display and works fine as normal. But after some attempts again gives the broblem stated above. Plz help
It sounds like your Xbox 360 Slim might be experiencing a hardware or connection issue. Here are some steps to troubleshoot: Ensure the HDMI or AV cables are securely connected to both the Xbox and the TV. Try using a different HDMI or AV cable to rule out a faulty cable. Test the console on another TV or monitor to see if the issue is with the display. Boot the Xbox 360 into Low-Resolution Mode: Turn off the console. Hold the Eject button and press the Power button. Keep holding the Eject button until you hear two beeps. This resets the display settings to default. Remove the hard drive and try booting the console without it. If it works, the hard drive might be faulty. If the power light turns red or flashes, note the number of lights and check the error code online for specific issues. If the problem persists, it could be a failing GPU, motherboard, or power supply. In this case, professional repair or replacement might be necessary. If none of these steps work, consider reaching out to a repair service or Xbox support for further assistance. Good luck!
Hi, I bought an original 360 slim, it turns on, it boots, green light, I connect the joypad but no video signal, I hope I don't have to change the hana kit otherwise I'll give up, do you have any suggestions? Can your video solve this problem? Thanks
Hi @gennarofierro5628! If your Xbox 360 Slim turns on, the green light shows, and the controller connects, but you’re not getting any video signal, there are a few things you can try before considering replacing the HANA chip: 1- Turn off the console. Press and hold the “Y” button on the controller and the right trigger at the same time. Turn the console on while holding both buttons. The display settings will reset, and it should boot in low resolution. 2- If you're using HDMI, try switching to Component or Composite cables (if available) to see if the video output is the issue. 3- If the above steps don’t work, it could indeed be an issue with the HANA/Scaler chip, which handles video output. Before giving up, consider having someone with experience reflow or reball the chip. A full replacement is the last resort, but it's possible if you're comfortable with that level of repair. 4- Sometimes, this issue can also be caused by GPU or motherboard problems. If reflowing the HANA chip doesn’t work, reflowing the GPU might help. Give those a shot first, and let me know how it goes! Hopefully, it’s a simple fix and not the HANA chip! 😅
Hey @gennarofierro5628! If the AV cable worked and you got a display, it's a good sign that the HANA chip is not the issue. The problem is likely related to the HDMI port or the HDMI chip itself. Here’s what you can check next: Inspect the HDMI Port: Look for any physical damage or loose connections in the HDMI port. Check the HDMI Chip: Even if the HANA chip is fine, the HDMI chip (responsible for HDMI output) could still be faulty. Consider testing or replacing it. It seems like you're on the right track! Let me know if you need more details on testing or repairs. 😊
Sir my problem is coming in xbox 360s that light is turning on but no display controller is also connected(wireless) but no display and fan is also working Some days before xbox was giving same issue but displaying after some hrs but now from 2 days it's not displaying after many hours and just running the fan and light on....What should I doo plzzz help
@gamerplus9884 It sounds like your Xbox 360 might have a GPU or display output issue. Try checking the HDMI or AV cable to make sure it’s securely connected and test with a different cable if possible. If the issue persists, first check and verify for the RAMs biases, also it could be due to overheating or a failing GPU. A reflow of the GPU might help, but be cautious as it’s a delicate process. Let me know if you need more detailed steps!
Can someone please help me. Im from south africa and sony replacement parts are so hard or even impossible to come by. Any suggestions for trustworthy online markets.
When will you repair ps3 and chromeb9x brother your number is off for many days and no contact on WhatsApp too... kindly repair and update me its been around 1 month and a half month
My xbox360 j tagged. When powered on, the center green dot light turns on. The fan is running but no circle light and no display. Can u help me to resolve this?
If there is no display but the fan and power light work, it could be a problem with the GPU/CPU solder connections. You might need to perform a reflow or reball of the GPU/CPU, as cold or cracked solder joints are common issues in older consoles like the Xbox 360. If you are experienced with this, you can try reflowing the chips using a heat gun, or you may need professional repair services for a reball. Ensure that all JTAG wiring and modifications are still intact and properly connected. A loose connection can cause the console to fail to boot correctly. Open the console and inspect the motherboard for any bulging or leaking capacitors. These could be a cause of the display not working and would need to be replaced. If your JTAG mod has an issue, try booting into Xell by powering on the console with the eject button. If Xell boots, it’s likely a dashboard or NAND issue. If none of these steps resolve the issue, it might be a more serious hardware problem requiring deeper troubleshooting or repairs. Let me know if you need more specific instructions on any of the steps!
E72 - This error is related to a loose pin or a not existent NAND chip, can also happen if you flashed it badly with an Infectus chip and/or the NAND is dead. According to XBH: Error within Xam
This error is unknown but assumed to be a short either under Southbridge and (H)ANA chip. The 0023 secondary error code for the Xbox 360 console typically deals with the clock chip not responding. Due to most communication passing from the ANA/HANA to the southbridge, the southbridge could also be at fault.A reflow of the southbridge could fix your problem.
Aoa bhai maray pass xbox 360 fat jtag hai wo chat ty chal ty masla aya hai logo aata hai or wahan kch lines aajati hain 3/4 dafa on ki yai he masla tha phir ab on hoti hai pr display nai aata sir please guide kigia ga or apna koi contact bhe dgia ga k agr repair kara ni ho ap se to babda kara sakay shukria
Nice update XBOX360 video , my JAPAN XBOX 360 ( 20unit ) just arrived hope giving less error , How much does it sell XBOX 360 in PAKISTAN. Mine cost me USD25/per unit including shipping + tax . ( MALAYSIA )
Yeah, it's a common issue with the Xbox 360 Slim! Glad you could relate to the video. If you run into it again, feel free to try the steps I showed, and let me know how it goes. Hopefully, it's sorted for good this time!
You're welcome! If you run into any issues or need further assistance while checking things out, feel free to ask. I'll be happy to help you troubleshoot or guide you through any steps. Good luck!
Well done! What broken 360 consoles do you recommend to buy, how to spot consoles that dont need bga rework?
It's difficult to provide information about it.
Keep up the work
I have the same issue but the difference is there is no voice of fan or machine from box😢 what is the problem in it ??
Can anybody help
Me too
Yesterday my Xbox 360 Slim Cause this same Issue after Restarting and unplugged all the cables I turn it on again bit suddenly It Showed Red Dot And Some kind of Error Messege on the screen After turning it off and turn On again It worked Perfectly i played 2 hours with it . But today Same Green Power Light on but no display
Same thing happened to me and my xbox works fine😅
😱
AoA. Sir i admire your great work. I have xbox 360 slim. It turns on gives a green light (if controller is connected, the controller lights also keep blinking) the green light of console is constantly on but there's no display.
However, the xbox sometimes gives display and works fine as normal. But after some attempts again gives the broblem stated above. Plz help
It sounds like your Xbox 360 Slim might be experiencing a hardware or connection issue. Here are some steps to troubleshoot:
Ensure the HDMI or AV cables are securely connected to both the Xbox and the TV.
Try using a different HDMI or AV cable to rule out a faulty cable.
Test the console on another TV or monitor to see if the issue is with the display.
Boot the Xbox 360 into Low-Resolution Mode:
Turn off the console.
Hold the Eject button and press the Power button.
Keep holding the Eject button until you hear two beeps.
This resets the display settings to default.
Remove the hard drive and try booting the console without it. If it works, the hard drive might be faulty.
If the power light turns red or flashes, note the number of lights and check the error code online for specific issues.
If the problem persists, it could be a failing GPU, motherboard, or power supply. In this case, professional repair or replacement might be necessary.
If none of these steps work, consider reaching out to a repair service or Xbox support for further assistance. Good luck!
@@idreestech sir you are amazing mashallah
I'll try these solutions. And will respond accordingly
Mine actually boots up, with logo animation then freezes and screen turns black. Do you have any idea why? Thanks so much in advance
The NAND data could be corrupted.
Hi, I bought an original 360 slim, it turns on, it boots, green light, I connect the joypad but no video signal, I hope I don't have to change the hana kit otherwise I'll give up, do you have any suggestions? Can your video solve this problem? Thanks
Hi @gennarofierro5628! If your Xbox 360 Slim turns on, the green light shows, and the controller connects, but you’re not getting any video signal, there are a few things you can try before considering replacing the HANA chip:
1- Turn off the console.
Press and hold the “Y” button on the controller and the right trigger at the same time.
Turn the console on while holding both buttons.
The display settings will reset, and it should boot in low resolution.
2- If you're using HDMI, try switching to Component or Composite cables (if available) to see if the video output is the issue.
3- If the above steps don’t work, it could indeed be an issue with the HANA/Scaler chip, which handles video output. Before giving up, consider having someone with experience reflow or reball the chip. A full replacement is the last resort, but it's possible if you're comfortable with that level of repair.
4- Sometimes, this issue can also be caused by GPU or motherboard problems. If reflowing the HANA chip doesn’t work, reflowing the GPU might help.
Give those a shot first, and let me know how it goes! Hopefully, it’s a simple fix and not the HANA chip! 😅
@@idreestech thanks for your prompt reply, my thanks are by following your youtube page
I tried the AV cable and it worked so I assume the hana chip is out of the question right?
Hey @gennarofierro5628! If the AV cable worked and you got a display, it's a good sign that the HANA chip is not the issue. The problem is likely related to the HDMI port or the HDMI chip itself. Here’s what you can check next:
Inspect the HDMI Port: Look for any physical damage or loose connections in the HDMI port.
Check the HDMI Chip: Even if the HANA chip is fine, the HDMI chip (responsible for HDMI output) could still be faulty. Consider testing or replacing it.
It seems like you're on the right track! Let me know if you need more details on testing or repairs. 😊
And if the controller dont turn on?
Sir my problem is coming in xbox 360s that light is turning on but no display controller is also connected(wireless) but no display and fan is also working Some days before xbox was giving same issue but displaying after some hrs but now from 2 days it's not displaying after many hours and just running the fan and light on....What should I doo plzzz help
@gamerplus9884 It sounds like your Xbox 360 might have a GPU or display output issue. Try checking the HDMI or AV cable to make sure it’s securely connected and test with a different cable if possible. If the issue persists, first check and verify for the RAMs biases, also it could be due to overheating or a failing GPU. A reflow of the GPU might help, but be cautious as it’s a delicate process. Let me know if you need more detailed steps!
I've followed your method, but why does my Xbox still not want to enter the freestyle menu, it just turns on the green light
I'm from Indonesian
Did you find a fix?
@@Closure4L couldn't find a fix
@@rickysaputra4195 😪am bout to give up
@@Closure4L and now the xbox is completely dead
Can someone please help me. Im from south africa and sony replacement parts are so hard or even impossible to come by. Any suggestions for trustworthy online markets.
Microsoft, Apple etc. Links please
When will you repair ps3 and chromeb9x brother your number is off for many days and no contact on WhatsApp too... kindly repair and update me its been around 1 month and a half month
My xbox 360 turns on but no green light and no display and the controllers wont work
🖥️🤓
Hi Master, Did you find a replacement for dap049? 😢
No dear! Not yet.
Hi my ps3 does some free,ing problem showing static thing on screen how do i fix it?
Please view the video related to the issue.
My xbox360 j tagged. When powered on, the center green dot light turns on. The fan is running but no circle light and no display. Can u help me to resolve this?
If there is no display but the fan and power light work, it could be a problem with the GPU/CPU solder connections. You might need to perform a reflow or reball of the GPU/CPU, as cold or cracked solder joints are common issues in older consoles like the Xbox 360.
If you are experienced with this, you can try reflowing the chips using a heat gun, or you may need professional repair services for a reball.
Ensure that all JTAG wiring and modifications are still intact and properly connected. A loose connection can cause the console to fail to boot correctly.
Open the console and inspect the motherboard for any bulging or leaking capacitors. These could be a cause of the display not working and would need to be replaced.
If your JTAG mod has an issue, try booting into Xell by powering on the console with the eject button. If Xell boots, it’s likely a dashboard or NAND issue.
If none of these steps resolve the issue, it might be a more serious hardware problem requiring deeper troubleshooting or repairs. Let me know if you need more specific instructions on any of the steps!
xbox 360 phat Red ring code 0003 can be fixed or?
Let me check.
Ihave a error 72 how fix it
E72 - This error is related to a loose pin or a not existent NAND chip, can also happen if you flashed it badly with an Infectus chip and/or the NAND is dead. According to XBH: Error within Xam
I have Xbox 360 jasper it has error code 0023 pls help
This error is unknown but assumed to be a short either under Southbridge and (H)ANA chip.
The 0023 secondary error code for the Xbox 360 console typically deals with the clock chip not responding.
Due to most communication passing from the ANA/HANA to the southbridge, the southbridge could also be at fault.A reflow of the southbridge could fix your problem.
Nice job..
Thanks!
Aoa bhai maray pass xbox 360 fat jtag hai wo chat ty chal ty masla aya hai logo aata hai or wahan kch lines aajati hain 3/4 dafa on ki yai he masla tha phir ab on hoti hai pr display nai aata sir please guide kigia ga or apna koi contact bhe dgia ga k agr repair kara ni ho ap se to babda kara sakay shukria
Please review the channel description. It appears that there may be some issues with RAM or the GPU.
good job
Thanks
Nice update XBOX360 video , my JAPAN XBOX 360 ( 20unit ) just arrived hope giving less error , How much does it sell XBOX 360 in PAKISTAN. Mine cost me USD25/per unit including shipping + tax . ( MALAYSIA )
Same here.
well my Xbox 360 does not have a jtag chip it is software based what I can do ?
Ignore the chip. Check for the 60 ohms biases on all RAMs.
2 times I got this problem
Yeah, it's a common issue with the Xbox 360 Slim! Glad you could relate to the video. If you run into it again, feel free to try the steps I showed, and let me know how it goes. Hopefully, it's sorted for good this time!
@@idreestech thank you for your comment I will check it see if I get make it
You're welcome! If you run into any issues or need further assistance while checking things out, feel free to ask. I'll be happy to help you troubleshoot or guide you through any steps. Good luck!
bhai urdu mein video bnani thi
I apologize for this.